Stresses encountered in the metal forming processes are less than the __________ of the material. (A) Fracture strength (B) Yield strength(C) Elastic limit (D) Limit of proportionality

Stresses encountered in the metal forming processes are less than the
__________ of the material.
(A) Fracture strength
(B) Yield strength
(C) Elastic limit
(D) Limit of proportionality
by

1 Answer

Answer :

Option A
by

Related questions

Fibrous fracture is normally encountered in the __________ materials. (A) Hard (B) Elastic (C) Ductile

Description : Fibrous fracture is normally encountered in the __________ materials. (A) Hard (B) Elastic (C) Ductile

Last Answer : Option C

Every material obeys the Hooke's law within its (A) Elastic limit (B) Plastic point (C) Limit of proportionality (D) None of these

Description : Every material obeys the Hooke's law within its (A) Elastic limit (B) Plastic point (C) Limit of proportionality (D) None of these

Last Answer : (C) Limit of proportionality

Every material obeys the Hooke’s law within (a) Elastic limit (b) Plastic limit (c) Limit of proportionality (d) None of these

Description : Every material obeys the Hooke’s law within (a) Elastic limit (b) Plastic limit (c) Limit of proportionality (d) None of these

Last Answer : c) Limit of proportionality

Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Last Answer : (B) Endurance limit

Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails (A) Below the yield point (B) Above the yield point (C) Below the elastic limit (D) At the elastic limit

Description : Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails (A) Below the yield point (B) Above the yield point (C) Below the elastic limit (D) At the elastic limit

Last Answer : Option A

In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Description : In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Last Answer : (a)Firstly Ultimate >yield > elastic limit

In a brittle material, the strength are (a) Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Description : In a brittle material, the strength are (a) Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Last Answer : (c) Thirdly Ultimate=yield=elastic limit

When stress is increased beyond elastic limit and material is permanently changed this property is a) Permanent stress b) Elasticity c) Yield strength d) Plasticity

Description : When stress is increased beyond elastic limit and material is permanently changed this property is a) Permanent stress b) Elasticity c) Yield strength d) Plasticity

Last Answer : d) Plasticity

Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Description : Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Last Answer : (A) Applies to elastic deformation

Hooke’s law is applicable within (a)Elastic limit (b)Plastic limit (c)Fracture point (d) Ultimate strength

Description : Hooke’s law is applicable within (a)Elastic limit (b)Plastic limit (c)Fracture point (d) Ultimate strength

Last Answer : (a)Elastic limit

The ductility of metal is usually expressed in terms of the: A. Yield strength (point where the material is not longer elastic) B. Percent elongation C. Modulus of elasticity (stiffness of the material)

Description : The ductility of metal is usually expressed in terms of the: A. Yield strength (point where the material is not longer elastic) B. Percent elongation C. Modulus of elasticity (stiffness of the material)

Last Answer : B. Percent elongation

Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild steel bar in tension from initial zero strain to failure is (a) 4, 1, 2, 3 and 5 (b) 1, 4, 3, 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Description : Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild ... , 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Last Answer : (c) 4, 1, 3, 5 and 2

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Last Answer : (a) Fatigue Failure

At ‘yield point’ of a copper wire A. the load hasn't exceeded the elastic limit yet; so, Hooke's law applies B. the load has already exceeded the elastic limit and the material has become plastic C. even the plastic stage has passed and the wire has snapped already D. Like Brass and Bronze, Copper has no yield poin

Description : At yield point' of a copper wire A. the load hasn't exceeded the elastic limit yet; so, Hooke's law applies B. the load has already exceeded the elastic limit and the material has become ... stage has passed and the wire has snapped already D. Like Brass and Bronze, Copper has no yield poin

Last Answer : the load has already exceeded the elastic limit and the material has become plastic

Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Description : Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Last Answer : (d) below the yield point

The limit beyond which the material does not behave elastically is known as (a) Proportional limit (b) Elastic limit (c) Plastic limit (d) Yield Point

Description : The limit beyond which the material does not behave elastically is known as (a) Proportional limit (b) Elastic limit (c) Plastic limit (d) Yield Point

Last Answer : (b) Elastic limit

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit

__________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength. (A) Lancing (B) Shot peening (C) Slugging (D) Spinning

Description : __________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength. (A) Lancing (B) Shot peening (C) Slugging (D) Spinning

Last Answer : (B) Shot peening

Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working

Description : Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working

Last Answer : Option B

In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to reach its permissible limit before to reach yield stress in steel [ C ] stresses in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Description : In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to ... in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Last Answer : [ A ] the stress in steel to reach its yield limit before concrete failure

In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to reach its permissible limit before to reach yield stress in steel [ C ] stresses in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Description : In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to ... in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Last Answer : [ A ] the stress in steel to reach its yield limit before concrete failure

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Description : Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Last Answer : b. Soderberg line

Out of the following processes of paper pulp manufacture, the maximum corrosion problem in digestion & handling equipments is encountered in the __________ process. (A) Mechanical (B) Sulphate/Kraft (C) Sulphite (D) Neutral sulphite semi-chemical

Description : Out of the following processes of paper pulp manufacture, the maximum corrosion problem in digestion & handling equipments is encountered in the __________ process. (A) Mechanical (B) Sulphate/Kraft (C) Sulphite (D) Neutral sulphite semi-chemical

Last Answer : (D) Neutral sulphite semi-chemical

Isotropic materials have the same __________ in all directions. (A) Induced stresses (B) Density (C) Elastic properties (D) Thermal properties

Description : Isotropic materials have the same __________ in all directions. (A) Induced stresses (B) Density (C) Elastic properties (D) Thermal properties

Last Answer : C) Elastic properties

The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point

Description : The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point

Last Answer : (b) Proportional Limit

Catalytic cracking compared to thermal cracking of residue of vacuum distillation of crude oil (A) Gives higher yield of petrol (B) Lower octane number of petrol (C) Higher sulphur content in the product (D) Higher gum forming material in petro

Description : Catalytic cracking compared to thermal cracking of residue of vacuum distillation of crude oil (A) Gives higher yield of petrol (B) Lower octane number of petrol (C) Higher sulphur content in the product (D) Higher gum forming material in petro

Last Answer : (A) Gives higher yield of petrol

Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Description : Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Last Answer : (D) Elastic limit close to ultimate breaking strength

Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Description : Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Last Answer : (D) Its elastic limit very close to ultimate breaking strength

Cast iron is having very high (A) Proximity between its elastic limit and ultimate breaking strength (B) Ductility (C) Tensile strength (D) All (A), (B) and (C)

Description : Cast iron is having very high (A) Proximity between its elastic limit and ultimate breaking strength (B) Ductility (C) Tensile strength (D) All (A), (B) and (C)

Last Answer : (A) Proximity between its elastic limit and ultimate breaking strength

Which of the manufacturing processes is/are required to make a typical stainless steel spoon out of sheet metal? A. Casting B. Forming C. Brazing D. Blow moulding

Description : Which of the manufacturing processes is/are required to make a typical stainless steel spoon out of sheet metal? A. Casting B. Forming C. Brazing D. Blow moulding

Last Answer : Forming

Yield strength of a material is determined by the __________ test. (A) Creep (B) Tension (C) Compression (D) Endurance

Description : Yield strength of a material is determined by the __________ test. (A) Creep (B) Tension (C) Compression (D) Endurance

Last Answer : Option B

Non-ferrous metals and hard steels do not exhibit a definite yield point, when pulled in the testing machine and hence for these cases, a better measure of their elastic properties is defined by the __________ stress. (A) Ultimate (B) Yield point (C) Proof (D) None of these

Description : Non-ferrous metals and hard steels do not exhibit a definite yield point, when pulled in the testing machine and hence for these cases, a better measure of their elastic properties is defined by the __________ stress. (A) Ultimate (B) Yield point (C) Proof (D) None of these

Last Answer : (C) Proof

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned

Description : The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned

Last Answer : b) Fatigue

Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Description : Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Last Answer : E. Elastic limit was exceeded

Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Description : Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Last Answer : (A) Impact strength

At yield point of a test piece, the material (A) Obeys Hooke's law (B) Behaves in an elastic manner (C) Regains its original shape on removal of the load(D) Undergoes plastic deformation

Description : At yield point of a test piece, the material  (A) Obeys Hooke's law  (B) Behaves in an elastic manner  (C) Regains its original shape on removal of the load  (D) Undergoes plastic deformation 

Last Answer : (D) Undergoes plastic deformation 

The stress at which extension of a material takes place more quickly as compared to increase in load, is called (a) No elastic zone (b) Plastic point (c) Yield point (d) Breaking point

Description : The stress at which extension of a material takes place more quickly as compared to increase in load, is called (a) No elastic zone (b) Plastic point (c) Yield point (d) Breaking point

Last Answer : (c) Yield point

A material no longer behaves elastically beyond (A) Plastic limit (B) Limiting load (C) Elastic limit (D) Breaking load

Description : A material no longer behaves elastically beyond (A) Plastic limit (B) Limiting load (C) Elastic limit (D) Breaking load

Last Answer : (C) Elastic limit

spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Description : spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Last Answer : Option D

spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Description : spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Last Answer : Option D

Strain hardening effect in a metal subjected to cold working is due to the __________ mechanism. (A) Fracture (B) Dislocation (C) Slip (D) Twinning

Description : Strain hardening effect in a metal subjected to cold working is due to the __________ mechanism. (A) Fracture (B) Dislocation (C) Slip (D) Twinning

Last Answer : (C) Slip

Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is proportional to D3(D = mean coil diameter) or d4(d = wire diameter) (C) Crushing load or columns is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Description : Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is ... is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Last Answer : (C) Crushing load or columns is less than the buckling load

Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity of steel (4) Geometry of the section. Which of these statements are correct? (a) 2, 3 and 4 (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Last Answer : 1,2,4

High endurance limit of carburised machine parts is because of the fact that carburisation (A) Suppresses any stress concentration produced in the parts (B) Enhances the yield point of the material (C) Introduces a compressive layer on the surface (D) Produces a better surface finish

Description : High endurance limit of carburised machine parts is because of the fact that carburisation (A) Suppresses any stress concentration produced in the parts (B) Enhances the yield point of the material (C) Introduces a compressive layer on the surface (D) Produces a better surface finish

Last Answer : (C) Introduces a compressive layer on the surface

In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Description : In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Last Answer : (C) Appreciable strain hardening is produced

Yield strength of a polycrystalline metal with an average grain size ‘d’, is proportional to (A) d1/2 (B) d-1/2 (C) d (D) d-1

Description : Yield strength of a polycrystalline metal with an average grain size ‘d’, is proportional to (A) d1/2 (B) d-1/2 (C) d (D) d-1

Last Answer : (B) d-1/2