The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit

The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the
(A) Fatigue strength
(B) Creep strength
(C) Resilience
(D) Endurance limit
by

1 Answer

Answer :

D) Endurance limit
by

Related questions

The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Description : The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Last Answer : Option A

The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Last Answer : (d) completely reversed load

Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Last Answer : (B) Endurance limit

Slow plastic deformation of metals under a constant stress is termed as __________ failure. (A) Fatigue (B) Endurance (C) Creep (D) None of these

Description : Slow plastic deformation of metals under a constant stress is termed as __________ failure. (A) Fatigue (B) Endurance (C) Creep (D) None of these

Last Answer : (C) Creep

Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Description : Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Last Answer : (B) Fatigue

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

Slow and progressive deformation of a material with time under constant stress is called (A) Creep (B) Erosion (C) Resilience (D) None of these

Description : Slow and progressive deformation of a material with time under constant stress is called (A) Creep (B) Erosion (C) Resilience (D) None of these

Last Answer : (A) Creep

Yield strength of a material is determined by the __________ test. (A) Creep (B) Tension (C) Compression (D) Endurance

Description : Yield strength of a material is determined by the __________ test. (A) Creep (B) Tension (C) Compression (D) Endurance

Last Answer : Option B

A material is capable of resisting softening at high temperature, because of its property termed as (A) Hot temper (B) Hot hardness (C) Fatigue (D) Creep

Description : A material is capable of resisting softening at high temperature, because of its property termed as (A) Hot temper (B) Hot hardness (C) Fatigue (D) Creep

Last Answer : (B) Hot hardness

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Last Answer : (a) Fatigue Failure

Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Description : Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Last Answer : b. Soderberg line

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (C) Creep resistance

On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Description : On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Last Answer : (B) Toughnes

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

_____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Last Answer : (b) Pitting

Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Description : Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Last Answer : (B) Toughness

Tumbling is the process of improving the __________ of the materials/parts. (A) Surface finish (B) Fatigue limit (C) Creep limit (D) Surface cleanliness

Description : Tumbling is the process of improving the __________ of the materials/parts. (A) Surface finish (B) Fatigue limit (C) Creep limit (D) Surface cleanliness

Last Answer : Option D

Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Description : Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Last Answer : (A) Impact strength

High endurance limit of carburised machine parts is because of the fact that carburisation (A) Suppresses any stress concentration produced in the parts (B) Enhances the yield point of the material (C) Introduces a compressive layer on the surface (D) Produces a better surface finish

Description : High endurance limit of carburised machine parts is because of the fact that carburisation (A) Suppresses any stress concentration produced in the parts (B) Enhances the yield point of the material (C) Introduces a compressive layer on the surface (D) Produces a better surface finish

Last Answer : (C) Introduces a compressive layer on the surface

A material subjected __________ must have high resilience. (A) Shock loading (B) Vibration (C) Fatigue (D) Tension

Description : A material subjected __________ must have high resilience. (A) Shock loading (B) Vibration (C) Fatigue (D) Tension

Last Answer : (A) Shock loading

The property of the bearing material to yield and adopt its shape to that of journal is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Description : The property of the bearing material to yield and adopt its shape to that of journal is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Last Answer : (B) Conformability

The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Description : The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Last Answer : (A) Embeddability

Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Description : Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Last Answer : c) Creep

Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is proportional to D3(D = mean coil diameter) or d4(d = wire diameter) (C) Crushing load or columns is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Description : Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is ... is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2

Last Answer : (C) Crushing load or columns is less than the buckling load

Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails (A) Below the yield point (B) Above the yield point (C) Below the elastic limit (D) At the elastic limit

Description : Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails (A) Below the yield point (B) Above the yield point (C) Below the elastic limit (D) At the elastic limit

Last Answer : Option A

Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Description : Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Last Answer : (d) below the yield point

A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength

Description : A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength

Last Answer : (a) maximum normal stress theory

The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience

The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience

The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Last Answer : (A) Approaches yield point

The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Description : The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Last Answer : d) Fatigue

A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Description : A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Last Answer : B) Completely reversed

A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Description : A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Last Answer : (B) Completely reversed

Dielectric strength of a material is (A) Its energy storage capacity (B) A magnetic property (C) Its capacity to resist the flow of current(D) Its capacity to withstand high voltage

Description : Dielectric strength of a material is (A) Its energy storage capacity (B) A magnetic property (C) Its capacity to resist the flow of current (D) Its capacity to withstand high voltage

Last Answer : (D) Its capacity to withstand high voltage

Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Description : Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Last Answer : Option A

In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Description : In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Last Answer : (C) Appreciable strain hardening is produced

In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Description : In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Last Answer : [ C ] Characteristic load

In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Description : In Limit state design, the maximum working load that the structure has to withstand is called [ A ] Service load [ B ] Factored load [ C ] Characteristic load [ D ] Ultimate load

Last Answer : [ C ] Characteristic load

Distinguish between creep and fatigue.

Description : Distinguish between creep and fatigue.

Last Answer : Creep is low and progressive deformation of a material with time under a constant stress at high temperature applications. Fatigue is the reduced tendency of material to offer resistance to applied stress under repeated or fluctuating loading condition.

Distinguish Between Creep And Fatigue?

Description : Distinguish Between Creep And Fatigue?

Last Answer : Creep is low and progressive deformation of a material with time under a constant stress at high-temperature applications. Fatigue is the reduced tendency of material to offer resistance to applied stress under repeated or fluctuating loading condition.

The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1

Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1

Last Answer : b) 2

In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Description : In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Last Answer : a. Ferrous materials

spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Description : spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Last Answer : Option D

spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Description : spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these

Last Answer : Option D

Presence of nickel & chromium in steel does not raise its (A) Elastic limit (B) Machining properties (C) Ductility (D) Resilience Answer: Option A

Description : Presence of nickel & chromium in steel does not raise its (A) Elastic limit (B) Machining properties (C) Ductility (D) Resilience Answer: Option A

Last Answer : Option A

When stress is increased beyond elastic limit and material is permanently changed this property is a) Permanent stress b) Elasticity c) Yield strength d) Plasticity

Description : When stress is increased beyond elastic limit and material is permanently changed this property is a) Permanent stress b) Elasticity c) Yield strength d) Plasticity

Last Answer : d) Plasticity