Description : Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance
Last Answer : (B) Toughness
Description : On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue
Last Answer : (B) Toughnes
Description : Smith's test of stones is performed to find out (A) The presence of soluble matter of stone (B) The compressive strength of the stone (C) The hardness of the stone (D) The toughness of the stone
Last Answer : Answer: Option A
Description : Detrimental property of a material for shock load applications (a) High density (b) Low toughness (c) High strength (d) Low hardness
Last Answer : (b) Low toughness
Description : Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase
Last Answer : a) A reduced resistance to corrosion
Description : Grindability of a material does not depend upon its (A) Elasticity (B) Hardness (C) Toughness (D) Size
Last Answer : (D) Size
Description : The ability of a material to offer resistance to scratching or indentation is a measure of its (A) Brittleness (B) Toughness (C) Hardness (D) Resilience
Last Answer : (C) Hardness
Description : Pick out the correct statement. (A) Hot worked materials are subjected to annealing to remove internal stresses (B) Annealing of steel hardens it slightly (C) Normalising of a material induces stresses (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness
Last Answer : (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness Share
Description : A member which is subjected to reversible tensile or compressive stress may fail at a stress lower than the ultimate stress of the material. This property of metal, is called (A) Plasticity of the ... ) Elasticity of the metal (C) Fatigue of the metal (D) Workability of the metal
Last Answer : (C) Fatigue of the metal
Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength
Last Answer : (A) Modulus of elasticity (young's modulus)
Description : The area under stress-strain curve represents a.Hardness of material b.Breaking strength of the material c.Energy required to cause failure d.Toughness of material e.Malleabbility of material
Last Answer : c. Energy required to cause failure
Description : Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined
Last Answer : b) No, they are subjected to compressive forces only
Description : The moment of resistance of an over-reinforcement section is determined on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) None of these
Last Answer : (a) Compressive force developed in concrete
Description : The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these
Last Answer : B
Description : Non-ferrous alloys used for making cutting tools need not have high (A) Abrasion resistance (B) Toughness (C) Red hardness (D) Cutting speed
Last Answer : (C) Red hardness
Description : The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength
Last Answer : (A) Resilience
Description : The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength
Description : Tick of the property, which is different from the group (A) Ductility. (B) Resistivity. (C) Tensile strength. (D) Hardness.
Last Answer : (B) Resistivity
Description : Fatigue failure of a material results from __________ stress. (A) Tensile (B) Compressive (C) Fluctuating (D) None of these
Last Answer : (C) Fluctuating
Description : Fatigue failure of a material may occur, when it is subjected to __________ stress. (A) Fluctuating (B) Tensile (C) Compressive (D) Torsion
Last Answer : (A) Fluctuating
Description : __________ test is the appropriate test to determine whether a material is ductile or brittle. (A) Impact (B) Cupping (C) Hardness (D) Tensile
Last Answer : (A) Impact
Description : Temper brittleness of a material can be fairly detected by the __________ test. (A) Fatigue (B) Notched bar impact (C) Tensile (D) Hardness
Last Answer : Option B
Description : Le-Chatelier's device is used for determining the (A) Setting time of cement (B) Soundness of cement (C) Tensile strength of cement (D) Compressive strength of cement
Last Answer : Answer: Option B
Description : The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue
Last Answer : d) Fatigue
Description : The important test to be conducted on a stone used in docks and harbours is (A) Hardness test (B) Workability test (C) Weight test (D) Toughness test
Last Answer : Answer: Option C
Description : Define the terms: i) Hardness ii) Toughness iii) Brazing iv) Machinability
Last Answer : i) Hardness:- Hardness is the property of metal possessed by a material which enables it to resist penetration or abrasion or scratching by other material. Diamond is the hardest of known materials. ... can be easily cut by cutting tools to produce a desired shape & surface finish on its surface
Description : A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None
Last Answer : (c) Shear considerations only
Description : The value of Poison’s ratio depends upon (a) Nature of load, tensile or compressive (b) Magnitude of load (c) Material of the test specimen (d) Dimensions of the test specimen
Last Answer : (c) Material of the test specimen
Description : M10 index of coke indicates its (A) Compressive strength (B) Hardness (C) Abrasion resistance (D) Impact strength
Last Answer : Option C
Description : M10 index of coke indicates its (A) Compressive strength (B) Hardness (C) Abrasion resistance (D) Impact strength Answer: Option C
Description : A material is capable of resisting softening at high temperature, because of its property termed as (A) Hot temper (B) Hot hardness (C) Fatigue (D) Creep
Last Answer : (B) Hot hardness
Description : Most important property of steels for use in automobile bodies is the (A) Formability (B) Yield strength (C) Toughness (D) Resilience
Last Answer : (A) Formability
Description : Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these
Last Answer : (B) Tensile
Description : Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength
Last Answer : (C) Machinability
Description : Cast iron is (A) Used for making shock resisting parts (B) Manufactured in cupola and is brittle (C) Having compressive strength more than its tensile strength (D) All (A), (B) & (C)
Last Answer : (D) All (A), (B) & (C)
Description : Pick out the wrong statement pertaining to the properties of glasses. Glasses generally have (A) High electrical insulation properties (B) Sharp melting points (C) Low co-efficient of thermal expansion (D) Compressive strength much greater than their tensile strengths
Last Answer : (B) Sharp melting points
Description : Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion
Last Answer : (D) Thermal co-efficient of expansion
Description : __________ stress cannot be sustained by a fluid in equilibrium. (A) Shear (B) Tensile (C) Compressive
Last Answer : Option A
Description : Factor of safety is the ratio of the __________ stress to the working stress. (A) Tensile (B) Compressive (C) Yield (D) Bearing
Description : . In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness
Last Answer : (D) Hardness, rigidity & brittleness
Description : Cast irons are generally specified by their (A) Carbon content (B) Tensile strength (C) Hardness (D) Manufacturing process
Last Answer : (B) Tensile strength
Description : Manganese in steel affects its (A) Ductility (B) Tensile strength (C) Hardness (D) None of these
Description : With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'
Last Answer : (A) Impact strength
Description : In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'
Last Answer : (A) Percentage elongation
Description : Primary designation of steel is based on its (A) Hardness & tensile strength (B) Carbon content (C) Iron content (D) Alloying elements content
Last Answer : (D) Alloying elements content Sh
Description : The property due to which a metal can be hammered into thin sheets without breaking is _______. a) malleability b)ductility c)tensile strength d)conductivity
Last Answer : a) malleability
Description : The acceleration due to gravity is determined by using a simple pendulum of length l = (100 ± 0.1) cm. If its time period is T = (2 ± 0.01)
Last Answer : The acceleration due to gravity is determined by using a simple pendulum of length l = (100 ... the maximum percentage error in the measurement of g.
Description : The compressive strength of cement should not be less than about 110Kg/cm2 after three days & not less than 170Kg/cm2 after seven days. The fineness of an ordinary cement as determined by turbidimetric method should be about __________ cm2 /gm. (A) 800 (B) 1600 (C) 4000 (D) 8500
Last Answer : (B) 1600
Description : The ability of a material to absorb energy in the elastic range is a measure of its (A) Toughness (B) Resilience (C) Malleability (D) Brittleness
Last Answer : (B) Resilience