The initial gap between the extra full-length leaf and the graduated-length leaf before the assembly, is called as (A) clearance (B) nip (C) gap

The initial gap between the extra full-length leaf and the graduated-length leaf before the

assembly, is called as

(A) clearance

(B) nip

(C) gap
by

1 Answer

Answer :

(B) nip
by

Related questions

Nip is the initial gap between extra full length leaf and the graduated length leaf before the assembly. a) True b) False

Description : Nip is the initial gap between extra full length leaf and the graduated length leaf before the assembly. a) True b) False

Last Answer : a) True

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. Calculate the initial pre load required to close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can’t be determined

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined

Last Answer : (b) 4674.1N

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. If modulus of elasticity is 207000N/mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Last Answer : b) 24.9mm

Nipping is defined as leaving the gap between full length leaf and graduated length leaf. a) True b) False

Description : Nipping is defined as leaving the gap between full length leaf and graduated length leaf. a) True b) False

Last Answer : b) False

Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Description : Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Last Answer : b) No

Unnecessary and frequent applications of varnish to the generator windings to repair defective insulation will result in ____________. A. heavy coatings of varnish interfering with heat dissipation B. deficient air gap clearance and eventual damage to the casing C. failure of the rectifier assembly D. a built-up of varnish without changing generator operation

Description : Unnecessary and frequent applications of varnish to the generator windings to repair defective insulation will result in ____________. A. heavy coatings of varnish interfering with heat dissipation B. ... of the rectifier assembly D. a built-up of varnish without changing generator operation

Last Answer : Answer: A

Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)

Description : Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)

Last Answer : (A) cos α = (dr + dp)/(dr + df)

A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Last Answer : (a) S = (μN s /p) (r/c) 2

Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the using the code given below: (a) 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Description : Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the ... 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Last Answer : (b) 1 and 3 only

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Description : A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Last Answer : b) Journal radius is kept smaller

Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Description : Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Last Answer : d) Helps in locking of the fastener

Just graduated college and have some extra money to go on a trip. where should I go and why?

Description : Just graduated college and have some extra money to go on a trip. where should I go and why?

Last Answer : It’s such a generic answer but I would travel around Europe. I’d learn some new languages, see lots of famous monuments and museums, and see how a whole lot of other people live. And congrats on graduation!

A rolling contact bearing is specified as X307. Determine the series. a) Extra light series b) Light series c) Medium series d) Heavy series

Description : A rolling contact bearing is specified as X307. Determine the series. a) Extra light series b) Light series c) Medium series d) Heavy series

Last Answer : c) Medium series

The longest leaf in a leaf spring is called centre leaf. a) It is called middle leaf b) It is called master leaf c) Yes d) None of the listed

Description : The longest leaf in a leaf spring is called centre leaf. a) It is called middle leaf b) It is called master leaf c) Yes d) None of the listed

Last Answer : b) It is called master leaf

The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Description : The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Last Answer : (d) all the mentioned

The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Last Answer : (A) Approaches yield point

The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by external cyclic load (C) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Last Answer : (D) All the three

The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors

Description : The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors

Last Answer : (D) All three factors

In manual assembly, cost of screw is higher than the cost of driving a screw. a) True b) False

Description : In manual assembly, cost of screw is higher than the cost of driving a screw. a) True b) False

Last Answer : b) False

Multi-leaf springs are used in (A) automobile suspension (B) railroad suspension (C) both (A) and (B) (D) none of the above

Description : Multi-leaf springs are used in (A) automobile suspension (B) railroad suspension (C) both (A) and (B) (D) none of the above

Last Answer : (C) both (A) and (B)

The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above

Description : The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above

Last Answer : (A) bending stress

The longest leaf in Semi-elliptic leaf spring is known as (A) chief leaf (B) master leaf (C) major leaf (D) higher leaf

Description : The longest leaf in Semi-elliptic leaf spring is known as (A) chief leaf (B) master leaf (C) major leaf (D) higher leaf

Last Answer : (B) master leaf

The type of spring used to absorb and release energy in mechanical watches is (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring

Description : The type of spring used to absorb and release energy in mechanical watches is (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring

Last Answer : (C) Spiral spring

The type of spring used to achieve greater load carrying capacity within given space is (A) Spiral spring (B) Springs in series (C) Multi-leaf spring (D) Concentric springs

Description : The type of spring used to achieve greater load carrying capacity within given space is (A) Spiral spring (B) Springs in series (C) Multi-leaf spring (D) Concentric springs

Last Answer : (D) Concentric springs

The type of spring used to measure weights in spring balance is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring

Description : The type of spring used to measure weights in spring balance is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring

Last Answer : (A) Helical extension spring

The type of spring used in door hinges is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring

Description : The type of spring used in door hinges is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring

Last Answer : (D) Helical torsion spring

The type of spring used to absorb shocks and vibrations in vehicles is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Belleville (coned disk) spring

Description : The type of spring used to absorb shocks and vibrations in vehicles is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Belleville (coned disk) spring

Last Answer : (B) Multi-leaf spring

Multi leaf springs are not recommended for automobile and rail road suspensions. a) True b) False

Description : Multi leaf springs are not recommended for automobile and rail road suspensions. a) True b) False

Last Answer : b) False

Bending stress in graduated length leaves are more than that in full length leaves. (a) Yes (b) No (c) In some cases (d) Can’t be stated

Description : Bending stress in graduated length leaves are more than that in full length leaves. (a) Yes (b) No (c) In some cases (d) Can’t be stated

Last Answer : (b) No

Initial gap between two turns of a close coil helical tension spring should be a. 0.5 mm b. based on the maximum deflection c. 1 mm d. zero

Description : Initial gap between two turns of a close coil helical tension spring should be a. 0.5 mm b. based on the maximum deflection c. 1 mm d. zero

Last Answer : d. zero

A proton and an alpha particle pass through the gap of a strong magnet. If both particles have the same initial velocity, how many times greater will the defection of the proton be relative to the deflection of the alpha particle? Will it be: w) the same x) 2 times y) 4 times z) 8 times

Description : A proton and an alpha particle pass through the gap of a strong magnet. If both particles have the same initial velocity, how many times greater will the defection of the proton be relative to the deflection of the alpha particle? Will it be: w) the same x) 2 times y) 4 times z) 8 times

Last Answer : ANSWER: X -- 2 TIMES

Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Description : Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Last Answer : (C) free length

If the spring is compressed completely and the adjacent coils touch each other,the the length of spring is called as? a) Solid length b) Compressed length c) Free length d) None of the mentioned

Description : If the spring is compressed completely and the adjacent coils touch each other,the the length of spring is called as? a) Solid length b) Compressed length c) Free length d) None of the mentioned

Last Answer : a) Solid length

The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Description : The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Last Answer : a) Leg

What is Nip ?

Description : What is Nip ?

Last Answer : Nip means to die.

Where can you watch Nip/Tuck?

Description : Where can you watch Nip/Tuck?

Last Answer : you can watch nip tuck season 7 here: http://free-movies-online-now.com

The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Description : The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Last Answer : (B) Roll

What is the usual value of angle of nip for crushing of ordinary rock in smooth steel crushing rolls? (A) 16° (B) 32° (C) 40° (D) 46°

Description : What is the usual value of angle of nip for crushing of ordinary rock in smooth steel crushing rolls? (A) 16° (B) 32° (C) 40° (D) 46°

Last Answer : (B) 32°

The value of 'angle of nip' is generally about (A) 16° (B) 32° (C) 52° (D) 64

Description : The value of 'angle of nip' is generally about (A) 16° (B) 32° (C) 52° (D) 64

Last Answer : (B) 32

Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will just take hold of a particle and draw it in the crushing zone (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing (D) Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Description : Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will ... Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Last Answer : (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing

. Which of the following relationships between co-efficient of friction (μ) between rock & roll and a (half of the angle of nip) of the particle to be crushed is correct? (A) μ > tan α (B) μ ≥ tan α (C) μ > tan 2α (D) μ ≤ tan α

Description : . Which of the following relationships between co-efficient of friction (μ) between rock & roll and a (half of the angle of nip) of the particle to be crushed is correct? (A) μ > tan α (B) μ ≥ tan α (C) μ > tan 2α (D) μ ≤ tan α

Last Answer : (B) μ ≥ tan α

Angle of nip of the crushing rolls does not depend upon the (A) Diameter of the rolls (B) Speed of the rolls (C) Product size (D) Feed size

Description : Angle of nip of the crushing rolls does not depend upon the (A) Diameter of the rolls (B) Speed of the rolls (C) Product size (D) Feed size

Last Answer : (B) Speed of the rolls

Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False

Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False

Last Answer : (b) False

The bearing characteristic number in a hydrodynamic bearing depends on- (a) Length, width and load (b) length, width and speed. [IES-1996] (c) Viscosity, speed and load (d) viscosity, speed and bearing pressure.

Description : The bearing characteristic number in a hydrodynamic bearing depends on- (a) Length, width and load (b) length, width and speed. [IES-1996] (c) Viscosity, speed and load (d) viscosity, speed and bearing pressure.

Last Answer : (d) viscosity, speed and bearing pressure.

The length to diameter ratio for a square bearing is (A) More than 1 (B) Less than 1 (C) 8 (D) 1

Description : The length to diameter ratio for a square bearing is (A) More than 1 (B) Less than 1 (C) 8 (D) 1

Last Answer : (D) 1

The length to diameter ratio for a short bearing is (A) More than 1 (B) Less than 1 (C) 8

Description : The length to diameter ratio for a short bearing is (A) More than 1 (B) Less than 1 (C) 8

Last Answer : (B) Less than 1

Needles bearing consist of rollers of small diameter and very small length. a) True b) False

Description : Needles bearing consist of rollers of small diameter and very small length. a) True b) False

Last Answer : b) False