Which of the following parts of a jaw crusher is subjected to maximumwear and tear during its operation?(A) Check plates(B) Jaw plates(C) Toggles(D) Crush shaft

Which of the following parts of a jaw crusher is subjected to maximumwear and tear during its operation?
(A) Check plates
(B) Jaw plates
(C) Toggles
(D) Crush shaft
by

1 Answer

Answer :

(B) Jaw plates
by

Related questions

Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman

Description : Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman

Last Answer : (A) Hanger

During size reduction by a jaw crusher, the energy consumed decreases with the (A) Decreasing size of product at constant size of feed (B) Decreasing machine capacity (C) Increasing size of feed at constant reduction ratio (D) None of these

Description : During size reduction by a jaw crusher, the energy consumed decreases with the (A) Decreasing size of product at constant size of feed (B) Decreasing machine capacity (C) Increasing size of feed at constant reduction ratio (D) None of these

Last Answer : (C) Increasing size of feed at constant reduction ratio

To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Last Answer : (B) Hammer crusher

Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these

Description : Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these

Last Answer : (A) Jaw crusher

Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Description : Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Last Answer : (C) Gyratory crusher

Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Description : Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Last Answer : (D) Fluid energy mil

According to Taggart's rule for selecting between a gyratory crusher and a jaw crusher; the later should be used, if the hourly tonnage to be crushed divided by the square of the gape expressed in cm is less than (A) 0.00184 (B) 0.0184 (C) 0.184 (D) 1.84

Description : According to Taggart's rule for selecting between a gyratory crusher and a jaw crusher; the later should be used, if the hourly tonnage to be crushed divided by the square of the gape expressed in cm is less than (A) 0.00184 (B) 0.0184 (C) 0.184 (D) 1.84

Last Answer : (B) 0.0184

Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Last Answer : (C) Jaw crusher

Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the(A) Blake jaw crusher(B) Cage mill(C) Stamp mill(D) Bradford's breaker

Description : Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the (A) Blake jaw crusher (B) Cage mill (C) Stamp mill (D) Bradford's breaker

Last Answer : (B) Cage mill

Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill(B) Ball mill, Jaw crusher, Fluid energy mill(C) Fluid energy mill, Jaw crusher, Ball mill(D) Fluid energy mill, Ball mill, Jaw crusher

Description : Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill (B) Ball mill, Jaw crusher, Fluid ... C) Fluid energy mill, Jaw crusher, Ball mill (D) Fluid energy mill, Ball mill, Jaw crusher

Last Answer : (A) Jaw crusher, Ball mill, Fluid energy mill

Choke crushing (in case of a Jaw crusher) compared to free crushing (A) Results in increased capacity (B) Consumes less power (C) Consumes more power (D) Both (A) and (C)

Description : Choke crushing (in case of a Jaw crusher) compared to free crushing (A) Results in increased capacity (B) Consumes less power (C) Consumes more power (D) Both (A) and (C)

Last Answer : (C) Consumes more power

The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Description : The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Last Answer : (B) 2.5 times

Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher(B) Cone crusher(C) Impact crusher(D) Toothed roll crushe

Description : Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher (B) Cone crusher (C) Impact crusher (D) Toothed roll crushe

Last Answer : (B) Cone crusher

Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusherFeed size of ≥ 25 cms can be accepted by(A) Ball mill(B) Rod mill(C) Fluid energy mill(D) Jaw crusher

Description : Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusher

Last Answer : (D) Jaw crusher

Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher

Description : Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher

Last Answer : (C) Toothed roll crusher

Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Description : Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Last Answer : (B) Toothed roll

Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one(B) There are only four methods namely compression, impact, attrition andcutting, which the size reduction equipments employ(C) Cutting machines mainly employ 'attrition' for size reduction of solids(D) Operating principles of Dodge and Blake jaw crushers are combined inthe working of universal jaw crushers

Description : Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one (B) There are only four methods namely compression, impact ... Operating principles of Dodge and Blake jaw crushers are combined in the working of universal jaw crushers

Last Answer : (C) Cutting machines mainly employ 'attrition' for size reduction of solids

Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087

Description : Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087

Last Answer : (B) 0.087 L.S

Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Last Answer : (B) Roll crusher

Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Description : Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Last Answer : i)Tray dryer:   ii)Plate column:    iii)Packed column:   iv) Jaw crusher:   v) Stirrer:   vi) Ball mill  

In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed(C) Clearance between hammer & grinding plates(D) All (A), (B) and (C

Description : In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed (C) Clearance between hammer & grinding plates (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Description : Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Last Answer : (A) Have greater capacity per unit of discharge area

. In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Description : . In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Last Answer : (D) Rotor shaft carrying hammers can be vertical or horizontal

Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size (C) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size

What use of vice jaw plates to protect the workpiece from damage?

Description : What use of vice jaw plates to protect the workpiece from damage?

Last Answer : What is the answer ?

During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above

Description : During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above

Last Answer : C) Bending stresses

During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above

Description : During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above

Last Answer : c. Bending stresses

The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Description : The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Last Answer : (B) Roll

Pick out the wrong statement. (A) Recycled coarse material to the grinder by a classifier is termed as circulating load (B) Wear and tear in wet crushing is more than that in dry crushing of materials (C) Size enlargement (opposite of size reduction) is not a mechanical operation (D) A 'dust catcher' is simply an enlargement in a pipeline which permits the solids to settle down due to reduction in velocity of the dust laden gas

Description : Pick out the wrong statement. (A) Recycled coarse material to the grinder by a classifier is termed as circulating load (B) Wear and tear in wet crushing is more than that in dry crushing of ... a pipeline which permits the solids to settle down due to reduction in velocity of the dust laden gas

Last Answer : (C) Size enlargement (opposite of size reduction) is not a mechanical operation

The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these

Description : The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these

Last Answer : (c) So that plates may become

The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these

Description : The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these

Last Answer : (c) So that plates may become flat, when subjected to design load

A flywheel weighs 400 kg and has a radius of gyration of 30 cm about its axis of rotation. It is mounted on a shaft subjected to a moment of 40 kgm. If the flywheel starts from restits speed after 3 seconds wil be a.10.9 rad/sec b.19.0 rad/sec c.51.2 rad/sec d.3.33 rad/sec e.16.35 rad/sec

Description : A flywheel weighs 400 kg and has a radius of gyration of 30 cm about its axis of rotation. It is mounted on a shaft subjected to a moment of 40 kgm. If the flywheel starts from restits speed after 3 seconds wil be a.10.9 rad/sec b.19.0 rad/sec c.51.2 rad/sec d.3.33 rad/sec e.16.35 rad/sec

Last Answer : d. 3.33 rad/sec

The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Description : The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Last Answer : (b) 37.29 kN

Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l

Description : Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l

Last Answer : d) Frictional torque is given by fpr2l

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : c) 16M/πdɜ

When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : b) 32M/πdɜ

A shaft is subjected to the...... A. Normal stress B. Bending stress C. Shear stress D. Combine stress E. All types

Description : A shaft is subjected to the...... A. Normal stress B. Bending stress C. Shear stress D. Combine stress E. All types

Last Answer : E. All types

When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : c) 16M/πdɜ

When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : b) 32M/πdɜ

A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent bending moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Description : A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent bending moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Last Answer : (D) Mb +√(Mb2 + Mt2)

A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent torsional moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Description : A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent torsional moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Last Answer : (B) √(Mb2 + Mt2)

A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams

Description : A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams

Last Answer : (A) Maximum principal stress theory

There are n rotors mounted on the shaft and when subjected to torsional vibration there will be A. N nodes B. (N-1) nodes C. (N+1) nodesD. Any number of nodes

Description : There are n rotors mounted on the shaft and when subjected to torsional vibration there will be A. N nodes B. (N-1) nodes C. (N+1) nodesD. Any number of nodes

Last Answer : B. (N-1) nodes

A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Description : A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the  maximum bending stress to maximum shear stress developed in the shaft, is  (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Last Answer : (C) 2M/T

If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5

Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque  when t attains maximum shear stress fs  the ratio of inner diameter to outer diameter, is 17/64  (fs/N)  (A) 1/2  (B) 1/3  (C) 1/4  (D) 1/5

Last Answer : (C) 1/4 

If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003

Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105  N/mm2 ) when subjected to a twisting  moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is  (A) 0.001  (B) 0.002  (C) 0.0025  (D) 0.003 

Last Answer : (C) 0.0025 

shaft subjected to a bending moment M and a torque T, experiences (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b) (D) Neither (a) nor (b)

Description :  shaft subjected to a bending moment M and a torque T, experiences  (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b)  (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b) 

A shaft 9 m long is subjected to a torque 30 t-m at a point 3 m distant from either end. The reactive torque at the nearer end will be (A) 5 tonnes metre (B) 10 tonnes metre (C) 15 tonnes metre (D) 20 tonnes metre

Description : A shaft 9 m long is subjected to a torque 30 t-m at a point 3 m distant from either end. The reactive torque at the nearer end will be (A) 5 tonnes metre (B) 10 tonnes metre (C) 15 tonnes metre (D) 20 tonnes metre

Last Answer : (D) 20 tonnes metre