According to Taggart's rule for selecting between a gyratory crusher and a jaw crusher; the later should be used, if the hourly tonnage to be crushed divided by the square of the gape expressed in cm is less than (A) 0.00184 (B) 0.0184 (C) 0.184 (D) 1.84

According to Taggart's rule for selecting between a gyratory crusher
and a jaw crusher; the later should be used, if the hourly tonnage to be
crushed divided by the square of the gape expressed in cm is less than
(A) 0.00184
(B) 0.0184
(C) 0.184
(D) 1.84
by

1 Answer

Answer :

(B) 0.0184
by

Related questions

The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Description : The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Last Answer : (B) 2.5 times

As per Taggart's formula, the capacity (kg/hr) of Jaw & Gyratory crushers (for gapes of 10 to 60 cms) is equal to (where, L = Length of feed opening, cms S = Maximum width of discharge opening, cms). (A) LS (B) 93 LS (C) 250 LS (D) √(LS)

Description : As per Taggart's formula, the capacity (kg/hr) of Jaw & Gyratory crushers (for gapes of 10 to 60 cms) is equal to (where, L = Length of feed opening, cms S = Maximum width of discharge opening, cms). (A) LS (B) 93 LS (C) 250 LS (D) √(LS)

Last Answer : (B) 93 LS

Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087

Description : Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087

Last Answer : (B) 0.087 L.S

The material is crushed in a gyratory crusher by the action of (A) Impact (B) Compression (C) Attrition (D) Cutting

Description : The material is crushed in a gyratory crusher by the action of (A) Impact (B) Compression (C) Attrition (D) Cutting

Last Answer : (B) Compression

Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these

Description : Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these

Last Answer : (A) Jaw crusher

Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Description : Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Last Answer : (C) Gyratory crusher

Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher

Description : Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher

Last Answer : (C) Toothed roll crusher

Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Description : Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Last Answer : (B) Toothed roll

Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Last Answer : (B) Roll crusher

To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Last Answer : (B) Hammer crusher

Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Description : Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Last Answer : (D) Fluid energy mil

Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one(B) There are only four methods namely compression, impact, attrition andcutting, which the size reduction equipments employ(C) Cutting machines mainly employ 'attrition' for size reduction of solids(D) Operating principles of Dodge and Blake jaw crushers are combined inthe working of universal jaw crushers

Description : Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one (B) There are only four methods namely compression, impact ... Operating principles of Dodge and Blake jaw crushers are combined in the working of universal jaw crushers

Last Answer : (C) Cutting machines mainly employ 'attrition' for size reduction of solids

Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Description : Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Last Answer : (A) Have greater capacity per unit of discharge area

For the preliminary breaking of hard rock, we use a (A) Gyratory crusher(B) Ball mill(C) Tube mill(D) Squirrel-cage disintegrator

Description : For the preliminary breaking of hard rock, we use a (A) Gyratory crusher (B) Ball mill (C) Tube mill (D) Squirrel-cage disintegrator

Last Answer : (A) Gyratory crusher

Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher(B) Ball mill(C) Roll crusher(D) Gyratory crusher

Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill

Description : Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill

Last Answer : (C) Gyratory crusher

Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Description : Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Last Answer : (B) Gyratory crusher

Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Description : Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure drop (C) Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Description : Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure ... Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Last Answer : (B) Cake resistance is independent of the pressure drop

Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size (C) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size

Choke crushing (in case of a Jaw crusher) compared to free crushing (A) Results in increased capacity (B) Consumes less power (C) Consumes more power (D) Both (A) and (C)

Description : Choke crushing (in case of a Jaw crusher) compared to free crushing (A) Results in increased capacity (B) Consumes less power (C) Consumes more power (D) Both (A) and (C)

Last Answer : (C) Consumes more power

Which of the following gives the crushing energy required to create new surface ? (A) Taggarts rule (B) Fick's law (C) Rittinger's Law (D) None of these

Description : Which of the following gives the crushing energy required to create new surface ? (A) Taggarts rule (B) Fick's law (C) Rittinger's Law (D) None of these

Last Answer : (C) Rittinger's Law

Pick out the correct statement: (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products (B) The operating cost of shaking screen is more than that of a vibrating screen (C) Screen capacity does not depend upon the specific gravity of the minerals (D) Asphalt is best crushed using toothed roll crusher

Description : Pick out the correct statement: (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products (B) The operating cost of ... upon the specific gravity of the minerals (D) Asphalt is best crushed using toothed roll crusher

Last Answer : (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products

The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Description : The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Last Answer : (B) Roll

Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Description : Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Last Answer : (A) Rod mills

Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Description : Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Last Answer : (B) Hammer crusher

The reverberation time of a 184.2 cubic meters broadcast studio is 0.84 sec. Find the absorption effect of the materials used in metric sabines. A. 35.3 B. 10.96 C. 379.8 D. 109.6

Description : The reverberation time of a 184.2 cubic meters broadcast studio is 0.84 sec. Find the absorption effect of the materials used in metric sabines. A. 35.3 B. 10.96 C. 379.8 D. 109.6

Last Answer : A. 35.3

A loudspeaker cabinet has an internal volume of 5,184 in3 (84,950 cm3 ). It has a port area on the baffle of 50 in2 (322.58cm2 ) and a thickness of 0.70 in (18 mm). What is the Helmholtz resonance, in hertz, of this loudspeaker enclosure? A. 250 Hz B. 245 Hz C. 240 Hz D. 255 Hz

Description : A loudspeaker cabinet has an internal volume of 5,184 in3 (84,950 cm3 ). It has a port area on the baffle of 50 in2 (322.58cm2 ) and a thickness of 0.70 in (18 mm). What is the Helmholtz resonance, in hertz, of this loudspeaker enclosure? A. 250 Hz B. 245 Hz C. 240 Hz D. 255 Hz

Last Answer : C. 240 Hz

Which of the following parts of a jaw crusher is subjected to maximumwear and tear during its operation?(A) Check plates(B) Jaw plates(C) Toggles(D) Crush shaft

Description : Which of the following parts of a jaw crusher is subjected to maximumwear and tear during its operation? (A) Check plates (B) Jaw plates (C) Toggles (D) Crush shaft

Last Answer : (B) Jaw plates

Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman

Description : Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman

Last Answer : (A) Hanger

During size reduction by a jaw crusher, the energy consumed decreases with the (A) Decreasing size of product at constant size of feed (B) Decreasing machine capacity (C) Increasing size of feed at constant reduction ratio (D) None of these

Description : During size reduction by a jaw crusher, the energy consumed decreases with the (A) Decreasing size of product at constant size of feed (B) Decreasing machine capacity (C) Increasing size of feed at constant reduction ratio (D) None of these

Last Answer : (C) Increasing size of feed at constant reduction ratio

Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Last Answer : (C) Jaw crusher

Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the(A) Blake jaw crusher(B) Cage mill(C) Stamp mill(D) Bradford's breaker

Description : Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the (A) Blake jaw crusher (B) Cage mill (C) Stamp mill (D) Bradford's breaker

Last Answer : (B) Cage mill

Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill(B) Ball mill, Jaw crusher, Fluid energy mill(C) Fluid energy mill, Jaw crusher, Ball mill(D) Fluid energy mill, Ball mill, Jaw crusher

Description : Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill (B) Ball mill, Jaw crusher, Fluid ... C) Fluid energy mill, Jaw crusher, Ball mill (D) Fluid energy mill, Ball mill, Jaw crusher

Last Answer : (A) Jaw crusher, Ball mill, Fluid energy mill

Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher(B) Cone crusher(C) Impact crusher(D) Toothed roll crushe

Description : Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher (B) Cone crusher (C) Impact crusher (D) Toothed roll crushe

Last Answer : (B) Cone crusher

Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusherFeed size of ≥ 25 cms can be accepted by(A) Ball mill(B) Rod mill(C) Fluid energy mill(D) Jaw crusher

Description : Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusher

Last Answer : (D) Jaw crusher

Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Description : Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Last Answer : i)Tray dryer:   ii)Plate column:    iii)Packed column:   iv) Jaw crusher:   v) Stirrer:   vi) Ball mill  

When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the permeability of the soil, is (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Description : When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the ... (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Last Answer : Answer: Option B

What is 3.0184 rounded to the nearest tenth and hundredth?

Description : What is 3.0184 rounded to the nearest tenth and hundredth?

Last Answer : 3.028

Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will just take hold of a particle and draw it in the crushing zone (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing (D) Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Description : Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will ... Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Last Answer : (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing

What does Gape mean ?

Description : What does Gape mean ?

Last Answer : Gape means to stare.

Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace

Description : Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace

Last Answer : (C) Tunnel kiln

Dead weight tonnage of a ship (i) Varies with latitude and season (ii) Is more than displacement tonnage (iii) Is the difference between displacement load and displacement light Of these statements (A) i) and ii) are correct (B) ii) and iii) are correct (C) i) and iii) are correct (D) Only iii) is correct

Description : Dead weight tonnage of a ship (i) Varies with latitude and season (ii) Is more than displacement tonnage (iii) Is the difference between displacement load and displacement light Of these statements (A) i) ... ii) and iii) are correct (C) i) and iii) are correct (D) Only iii) is correct

Last Answer : (C) i) and iii) are correct

5Star air conditioner will provide the same amount of colling using ___________ power than 1 star air conditioner of same tonnage. a) Lesser c) more b) Equal d) all of the above

Description : 5Star air conditioner will provide the same amount of colling using ___________ power than 1 star air conditioner of same tonnage. a) Lesser c) more b) Equal d) all of the above

Last Answer : Equal

If the time required for half change is inversely proportional to the square of initial concentration and the velocity depends on the units in which the concentration term is expressed, then the order of reaction is (A) 0 (B) 1 (C) 2 (D) 3

Description : If the time required for half change is inversely proportional to the square of initial concentration and the velocity depends on the units in which the concentration term is expressed, then the order of reaction is (A) 0 (B) 1 (C) 2 (D) 3

Last Answer : (D) 3

What is the tonnage of N4A34AKB200?

Description : What is the tonnage of N4A34AKB200?

Last Answer : Need answer

What is the tonnage On an Armstrong 2shp13le118p-1?

Description : What is the tonnage On an Armstrong 2shp13le118p-1?

Last Answer : Need answer

What is the tonnage of a Carrier 38YRA024330 and the seer?

Description : What is the tonnage of a Carrier 38YRA024330 and the seer?

Last Answer : Feel Free to Answer