. In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

. In case of a hammer crusher, the
(A) Feed may be highly abrasive (Moh's scale >5)
(B) Minimum product size is 3 mm
(C) Maximum feed size may be 50 mm
(D) Rotor shaft carrying hammers can be vertical or horizontal
by

1 Answer

Answer :

(D) Rotor shaft carrying hammers can be vertical or horizontal
by

Related questions

In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)

Description : In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed(C) Clearance between hammer & grinding plates(D) All (A), (B) and (C

Description : In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed (C) Clearance between hammer & grinding plates (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size (C) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size

In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine

Description : In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine

Last Answer : (C) Fine

In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Description : In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Last Answer : (B) Secondary

A pile is being driven with a drop hammer weighing 1800 kg and having a free fall of 1.00 m. If the penetration with last blow is 5 mm, the load carrying capacity of the pile, -according to the Engineering News formula, is (A) 100 tonnes (B) 50 tonnes (C) 20 tonnes (D) 10 tonnes

Description : A pile is being driven with a drop hammer weighing 1800 kg and having a free fall of 1.00 m. If the penetration with last blow is 5 mm, the load carrying capacity of the pile, -according to the Engineering News formula, is (A) 100 tonnes (B) 50 tonnes (C) 20 tonnes (D) 10 tonnes

Last Answer : (D) 10 tonnes

Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher(B) Ball mill(C) Roll crusher(D) Gyratory crusher

Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Description : Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Last Answer : (C) Tube mill

The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Description : The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Last Answer : (B) 2.5 times

Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Last Answer : (C) Jaw crusher

Energy consumption in a crusher decreases with increase in the (A) Size of the product (at constant feed size) (B) Capacity of the crushing machine (C) Size of feed (at constant reduction ratio) (D) All (A), (B) & (C)

Description : Energy consumption in a crusher decreases with increase in the (A) Size of the product (at constant feed size) (B) Capacity of the crushing machine (C) Size of feed (at constant reduction ratio) (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

During size reduction by a jaw crusher, the energy consumed decreases with the (A) Decreasing size of product at constant size of feed (B) Decreasing machine capacity (C) Increasing size of feed at constant reduction ratio (D) None of these

Description : During size reduction by a jaw crusher, the energy consumed decreases with the (A) Decreasing size of product at constant size of feed (B) Decreasing machine capacity (C) Increasing size of feed at constant reduction ratio (D) None of these

Last Answer : (C) Increasing size of feed at constant reduction ratio

For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm

Description : For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm

Last Answer : (B) 75 mm

In a size reduction crushing operation, feed size is 300 to 1500 mm while the product size is 100 to 300 mm. This is a case of the __________ crushing. (A) Secondary (B) Fine (C) Primary (D) Ultrafine

Description : In a size reduction crushing operation, feed size is 300 to 1500 mm while the product size is 100 to 300 mm. This is a case of the __________ crushing. (A) Secondary (B) Fine (C) Primary (D) Ultrafine

Last Answer : (C) Primary

For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm

Description : For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm

Last Answer : (a) 120 mm

A shaft carrying two rotor at its ends will have A No node B Two nodes C One node D Three nodes

Description : A shaft carrying two rotor at its ends will have A No node B Two nodes C One node D Three nodes

Last Answer : C One node

Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Last Answer : (B) Hammer crusher

The grinding in a hammer crusher takes place due to the (A) Attrition (B) Impact (C) Both (A) & (B) (D) Neither (A) nor (B

Description : The grinding in a hammer crusher takes place due to the (A) Attrition (B) Impact (C) Both (A) & (B) (D) Neither (A) nor (B

Last Answer : (C) Both (A) & (B)

Which of the following is not an ultrafine grinder (colloid mill)?(A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Description : Which of the following is not an ultrafine grinder (colloid mill)? (A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Last Answer : (C) Toothed roll crusher

To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Description : To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Last Answer : (D) Fluid energy mill

Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Description : Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Last Answer : (B) Hammer crusher

Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill

Description : Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill

Last Answer : (B) Roller crusher

Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Description : Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusherFeed size of ≥ 25 cms can be accepted by(A) Ball mill(B) Rod mill(C) Fluid energy mill(D) Jaw crusher

Description : Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusher

Last Answer : (D) Jaw crusher

Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Last Answer : (B) Roll crusher

Explain the rebound hammer test procedure and show the relationship between compressive strength and rebound number with hammer horizontal and vertical on dry and wet surface of concrete.

Description : Explain the rebound hammer test procedure and show the relationship between compressive strength and rebound number with hammer horizontal and vertical on dry and wet surface of concrete.

Last Answer : Rebound Hammer Test: i. Initially the plunger of rebound hammer is Kept touching to the target concrete surface ii. Then the tubular casing of hammer is pushed towards concrete, so that the spring gets ... of concrete will be less, But if it is more, then concrete possess sufficient strength.

Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810

Description : Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810

Last Answer : C 705

Juice extraction capacity of vertical three roller type bullock down sugercane crusher E. 50-70% F. 70-90% G. 90-100% H. 30-50%

Description : Juice extraction capacity of vertical three roller type bullock down sugercane crusher E. 50-70% F. 70-90% G. 90-100% H. 30-50%

Last Answer : E. 50-70%

Orthoclase is what number on Moh's hardness scale? w) 4 x) 5 y) 6 z) 7

Description : Orthoclase is what number on Moh's hardness scale? w) 4 x) 5 y) 6 z) 7

Last Answer : ANSWER: Y -- 6

Apatite is what number on Moh's (pron: moes: rhyme with toes) hardness scale? w) 1 x) 3 y) 5 z) 7

Description : Apatite is what number on Moh's (pron: moes: rhyme with toes) hardness scale? w) 1 x) 3 y) 5 z) 7

Last Answer : ANSWER: Y -- 5

Screw conveyors are (A) Run at very high rpm (B) Suitable for sticky materials (C) Suitable for highly abrasive materials (D) All (A), (B) and (C)

Description : Screw conveyors are (A) Run at very high rpm (B) Suitable for sticky materials (C) Suitable for highly abrasive materials (D) All (A), (B) and (C)

Last Answer : (B) Suitable for sticky materials

Mohs scale hardest is diamond - what's the softest?

Description : Mohs scale hardest is diamond - what's the softest?

Last Answer : Talc

What is the hardness gold on mohs scale?

Description : What is the hardness gold on mohs scale?

Last Answer : 2.5

What is the mohs scale hardness of iron ore?

Description : What is the mohs scale hardness of iron ore?

Last Answer : Depends on the ore- somewhere around a 6-8. Varies between hardand very hard. Also corrected spelling on the Mohs scale.

Diamond is what number on the Moh's hardness scale?

Description : Diamond is what number on the Moh's hardness scale?  

Last Answer : ANSWER: 10

Fluorite is what number on Moh's hardness scale? w) 1 x) 2 y) 3 z) 4

Description : Fluorite is what number on Moh's hardness scale? w) 1 x) 2 y) 3 z) 4

Last Answer : ANSWER: Z -- 4

Mohs scale hardest substance is diamond - what's the softest

Description : Mohs scale hardest substance is diamond - what's the softest

Last Answer : Talc

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Which of the following parts of a jaw crusher is subjected to maximumwear and tear during its operation?(A) Check plates(B) Jaw plates(C) Toggles(D) Crush shaft

Description : Which of the following parts of a jaw crusher is subjected to maximumwear and tear during its operation? (A) Check plates (B) Jaw plates (C) Toggles (D) Crush shaft

Last Answer : (B) Jaw plates

A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Description : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Last Answer : (b) 82 Mpa

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Last Answer : c. 50.57 N/mm2

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Description : In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Last Answer : (B) Decreases

Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should be multiplied with __________ to get the same for dry grinding. (A) 1.0 (B) 0.5 (C) 1.34 (D) 4.34

Description : Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should ... to get the same for dry grinding. (A) 1.0 (B) 0.5 (C) 1.34 (D) 4.34

Last Answer : (C) 1.34

On moving the feed line (q-line) from saturated liquid feed (vertical position) to saturated vapor feed (horizontal feed), if the slope of both the operating lines are to be increased, then it will result in (A) Greater degree of separation with a fixed number of trays (B) Increased reboiler load

Description : On moving the feed line (q-line) from saturated liquid feed (vertical position) to saturated vapor feed (horizontal feed), if the slope of both the operating lines are to be increased, then it will result in (A) Greater degree of separation with a fixed number of trays (B) Increased reboiler load

Last Answer : (C) Increased reflux ratio

In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c

Description : In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c

Last Answer : ans c

Forced circulation evaporators are useful for the concentration of viscous, salting and scale forming liquors. Which of the following is a forced circulation evaporator? (A) Long vertical evaporator (B) Horizontal tube evaporator (C) Agitated film evaporator (D) Calandria vertical tube evaporator

Description : Forced circulation evaporators are useful for the concentration of viscous, salting and scale forming liquors. Which of the following is a forced circulation evaporator? (A) Long vertical evaporator (B) Horizontal tube evaporator (C) Agitated film evaporator (D) Calandria vertical tube evaporator

Last Answer : (C) Agitated film evaporator