The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

The capacity of a gyratory crusher is __________ that of a jaw crusher
with the same gape, handling the same feed & for the same product size
range.
(A) Same as
(B) 2.5 times
(C) 5 times
(D) 10 times
by

1 Answer

Answer :

(B) 2.5 times
by

Related questions

According to Taggart's rule for selecting between a gyratory crusher and a jaw crusher; the later should be used, if the hourly tonnage to be crushed divided by the square of the gape expressed in cm is less than (A) 0.00184 (B) 0.0184 (C) 0.184 (D) 1.84

Description : According to Taggart's rule for selecting between a gyratory crusher and a jaw crusher; the later should be used, if the hourly tonnage to be crushed divided by the square of the gape expressed in cm is less than (A) 0.00184 (B) 0.0184 (C) 0.184 (D) 1.84

Last Answer : (B) 0.0184

Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Last Answer : (B) Roll crusher

Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Description : Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Last Answer : (B) Toothed roll

Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087

Description : Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087

Last Answer : (B) 0.087 L.S

Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size (C) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size

During size reduction by a jaw crusher, the energy consumed decreases with the (A) Decreasing size of product at constant size of feed (B) Decreasing machine capacity (C) Increasing size of feed at constant reduction ratio (D) None of these

Description : During size reduction by a jaw crusher, the energy consumed decreases with the (A) Decreasing size of product at constant size of feed (B) Decreasing machine capacity (C) Increasing size of feed at constant reduction ratio (D) None of these

Last Answer : (C) Increasing size of feed at constant reduction ratio

As per Taggart's formula, the capacity (kg/hr) of Jaw & Gyratory crushers (for gapes of 10 to 60 cms) is equal to (where, L = Length of feed opening, cms S = Maximum width of discharge opening, cms). (A) LS (B) 93 LS (C) 250 LS (D) √(LS)

Description : As per Taggart's formula, the capacity (kg/hr) of Jaw & Gyratory crushers (for gapes of 10 to 60 cms) is equal to (where, L = Length of feed opening, cms S = Maximum width of discharge opening, cms). (A) LS (B) 93 LS (C) 250 LS (D) √(LS)

Last Answer : (B) 93 LS

Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these

Description : Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these

Last Answer : (A) Jaw crusher

Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Description : Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Last Answer : (C) Gyratory crusher

Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher

Description : Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher

Last Answer : (C) Toothed roll crusher

To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Energy consumption in a crusher decreases with increase in the (A) Size of the product (at constant feed size) (B) Capacity of the crushing machine (C) Size of feed (at constant reduction ratio) (D) All (A), (B) & (C)

Description : Energy consumption in a crusher decreases with increase in the (A) Size of the product (at constant feed size) (B) Capacity of the crushing machine (C) Size of feed (at constant reduction ratio) (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Last Answer : (C) Jaw crusher

Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusherFeed size of ≥ 25 cms can be accepted by(A) Ball mill(B) Rod mill(C) Fluid energy mill(D) Jaw crusher

Description : Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusher

Last Answer : (D) Jaw crusher

Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will just take hold of a particle and draw it in the crushing zone (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing (D) Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Description : Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will ... Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Last Answer : (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing

Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Description : Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Last Answer : (A) Have greater capacity per unit of discharge area

Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher(B) Ball mill(C) Roll crusher(D) Gyratory crusher

Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure drop (C) Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Description : Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure ... Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Last Answer : (B) Cake resistance is independent of the pressure drop

Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Description : Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Last Answer : (A) Rod mills

Choke crushing (in case of a Jaw crusher) compared to free crushing (A) Results in increased capacity (B) Consumes less power (C) Consumes more power (D) Both (A) and (C)

Description : Choke crushing (in case of a Jaw crusher) compared to free crushing (A) Results in increased capacity (B) Consumes less power (C) Consumes more power (D) Both (A) and (C)

Last Answer : (C) Consumes more power

The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Description : The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Last Answer : (B) Roll

In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed(C) Clearance between hammer & grinding plates(D) All (A), (B) and (C

Description : In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed (C) Clearance between hammer & grinding plates (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Reciprocating screens are normally inclined at an angle of 5° with the horizontal and employ gyratory motion at feed end & reciprocating motion at the discharge end. They are not suitable for the screening of the (A) Light metal powder down upto 4 mesh size (B) Dry chemicals (C) Heavy tonnages of rocks or gravel (D) Powdered food & granular materials

Description : Reciprocating screens are normally inclined at an angle of 5° with the horizontal and employ gyratory motion at feed end & reciprocating motion at the discharge end. They are not suitable for the ... Dry chemicals (C) Heavy tonnages of rocks or gravel (D) Powdered food & granular materials

Last Answer : (C) Heavy tonnages of rocks or gravel

The material is crushed in a gyratory crusher by the action of (A) Impact (B) Compression (C) Attrition (D) Cutting

Description : The material is crushed in a gyratory crusher by the action of (A) Impact (B) Compression (C) Attrition (D) Cutting

Last Answer : (B) Compression

For the preliminary breaking of hard rock, we use a (A) Gyratory crusher(B) Ball mill(C) Tube mill(D) Squirrel-cage disintegrator

Description : For the preliminary breaking of hard rock, we use a (A) Gyratory crusher (B) Ball mill (C) Tube mill (D) Squirrel-cage disintegrator

Last Answer : (A) Gyratory crusher

Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill

Description : Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill

Last Answer : (C) Gyratory crusher

Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Description : Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Last Answer : (B) Gyratory crusher

Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Description : Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the(A) Blake jaw crusher(B) Cage mill(C) Stamp mill(D) Bradford's breaker

Description : Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the (A) Blake jaw crusher (B) Cage mill (C) Stamp mill (D) Bradford's breaker

Last Answer : (B) Cage mill

Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill(B) Ball mill, Jaw crusher, Fluid energy mill(C) Fluid energy mill, Jaw crusher, Ball mill(D) Fluid energy mill, Ball mill, Jaw crusher

Description : Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill (B) Ball mill, Jaw crusher, Fluid ... C) Fluid energy mill, Jaw crusher, Ball mill (D) Fluid energy mill, Ball mill, Jaw crusher

Last Answer : (A) Jaw crusher, Ball mill, Fluid energy mill

Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one(B) There are only four methods namely compression, impact, attrition andcutting, which the size reduction equipments employ(C) Cutting machines mainly employ 'attrition' for size reduction of solids(D) Operating principles of Dodge and Blake jaw crushers are combined inthe working of universal jaw crushers

Description : Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one (B) There are only four methods namely compression, impact ... Operating principles of Dodge and Blake jaw crushers are combined in the working of universal jaw crushers

Last Answer : (C) Cutting machines mainly employ 'attrition' for size reduction of solids

Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Last Answer : (B) Hammer crusher

. In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Description : . In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Last Answer : (D) Rotor shaft carrying hammers can be vertical or horizontal

Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher(B) Cone crusher(C) Impact crusher(D) Toothed roll crushe

Description : Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher (B) Cone crusher (C) Impact crusher (D) Toothed roll crushe

Last Answer : (B) Cone crusher

Which of the following parts of a jaw crusher is subjected to maximumwear and tear during its operation?(A) Check plates(B) Jaw plates(C) Toggles(D) Crush shaft

Description : Which of the following parts of a jaw crusher is subjected to maximumwear and tear during its operation? (A) Check plates (B) Jaw plates (C) Toggles (D) Crush shaft

Last Answer : (B) Jaw plates

Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Description : Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Last Answer : (D) Fluid energy mil

Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman

Description : Which of the following is not a part of the Blake jaw crusher? (A) Hanger (B) Check plates (C) Toggles (D) Pitman

Last Answer : (A) Hanger

In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)

Description : In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Description : Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Last Answer : i)Tray dryer:   ii)Plate column:    iii)Packed column:   iv) Jaw crusher:   v) Stirrer:   vi) Ball mill  

Wet grinding in a revolving mill __________ as compared to dry grinding. (A) Gives less wear on chamber walls (B) Requires more energy (C) Increases capacity (D) Complicates handling of the product

Description : Wet grinding in a revolving mill __________ as compared to dry grinding. (A) Gives less wear on chamber walls (B) Requires more energy (C) Increases capacity (D) Complicates handling of the product

Last Answer : (C) Increases capacity

In case of a revolving mill, wet grinding compared to dry grinding (A) Requires more energy (B) Has less capacity (C) Complicates handling & classification of the product (D) None of these

Description : In case of a revolving mill, wet grinding compared to dry grinding (A) Requires more energy (B) Has less capacity (C) Complicates handling & classification of the product (D) None of these

Last Answer : (D) None of these

Horsepower required for a roll crusher is directly proportional to its (A) Reduction ratio (B) Capacity(C) Both (A) & (B)(D) Neither (A) nor (B)

Description : Horsepower required for a roll crusher is directly proportional to its (A) Reduction ratio (B) Capacity (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

A centrifugal pump designed for handling water (μ = 1 cp) will deliver __________ when pumping a thicker oil (μ = 30 cp). (A) Less head & capacity (B) More head (C) More capacity (D) Less head & more capacity

Description : A centrifugal pump designed for handling water (μ = 1 cp) will deliver __________ when pumping a thicker oil (μ = 30 cp). (A) Less head & capacity (B) More head (C) More capacity (D) Less head & more capacity

Last Answer : (A) Less head & capacity

Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)

Description : Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)

Last Answer : (A) cos α = (dr + dp)/(dr + df)

Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should be multiplied with __________ to get the same for dry grinding. (A) 1.0 (B) 0.5 (C) 1.34 (D) 4.34

Description : Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should ... to get the same for dry grinding. (A) 1.0 (B) 0.5 (C) 1.34 (D) 4.34

Last Answer : (C) 1.34

Size reduction of asbestos and mica is done by (A) Hammer mills (B) Rod mills (C) Gyratory crushers (D) Crushing rolls

Description : Size reduction of asbestos and mica is done by (A) Hammer mills (B) Rod mills (C) Gyratory crushers (D) Crushing rolls

Last Answer : (A) Hammer mills

Pick out the correct statement: (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products (B) The operating cost of shaking screen is more than that of a vibrating screen (C) Screen capacity does not depend upon the specific gravity of the minerals (D) Asphalt is best crushed using toothed roll crusher

Description : Pick out the correct statement: (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products (B) The operating cost of ... upon the specific gravity of the minerals (D) Asphalt is best crushed using toothed roll crusher

Last Answer : (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products

In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine

Description : In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine

Last Answer : (C) Fine

In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Description : In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Last Answer : (B) Secondary