What is the advantage of sliding bearings over roller bearings?

What is the advantage of sliding bearings over roller bearings?
by

1 Answer

Answer :

In roller bearing for a given movement the roller bearing exhibit a change in pressure centre from its original position by one­half of its movement based on David J. Lee. However, with sliding bearing a sliding plate is attached to the upper superstructure and the moving part of bearing element is built in the substructure. It follows that there is no change in pressure center after the movement.
by

Related questions

Polytetrafluoroethylene (PTFE) is commonly used in sliding bearings. Why?

Description : Polytetrafluoroethylene (PTFE) is commonly used in sliding bearings. Why?

Last Answer : The choice of sliding surface of bearings is of vital importance because the sliding surfaces generate frictional forces which are exerted on the bearings and substructure of the bridge. For ... be designed with dimples to avoid the lubricant from squeezing out under repeated translation movements.

Under what situation should engineers use pot bearings instead of elastomeric bearings?

Description : Under what situation should engineers use pot bearings instead of elastomeric bearings?

Last Answer : In the event of high vertical loads combined with large angle of rotations, rubber bearings are undesirable when compared with pot bearings. For instance, elastomeric ... bearings are better alternatives than elastomeric bearings in such an scenario as suggested by David J. Lee.

In a curved prestressed bridge, how should the guided bearings in piers of the curved region be oriented with respect to the fixed bearing in abutment?

Description : In a curved prestressed bridge, how should the guided bearings in piers of the curved region be oriented with respect to the fixed bearing in abutment?

Last Answer : To determine the orientation of guided bearings, one should understand the movement of curved region of a prestressed bridge. Movement of prestress and creep are tangential to the curvature of the ... large, temporary freedom of movement at the guided bearings has to be provided during construction.

How to determine the size of elastomeric bearings?

Description : How to determine the size of elastomeric bearings?

Last Answer : For elastomeric bearing, the vertical load is resisted by its compression while shear resistance of the bearing controls the horizontal movements. The design ... and fatigue damage. The vertical stiffness of bearings is obtained by inserting sufficient number of steel plates.

In the design of elastomeric bearings, why are steel plates inserted inside the bearings?

Description : In the design of elastomeric bearings, why are steel plates inserted inside the bearings?

Last Answer : For elastomeric bearing to function as a soft spring, the bearing should be allowed for bulging laterally and the compression stiffness can be increased by limiting the amount of lateral bulging. To ... , the presence of metal plates does not affect the shear stiffness of the elastomeric bearings.

What is “preset” during installation of bridge bearings?

Description : What is “preset” during installation of bridge bearings?

Last Answer : Preset is a method to reduce the size of upper plates of sliding bearings in order to save the material cost. The normal length of a upper bearing plate should be composed of the ... of a certain distance of sliding bearings with respect to upper bearing plates during installation of bearings.

What is sucker deck principle for variable depth bridge decks?

Description : What is sucker deck principle for variable depth bridge decks?

Last Answer : For a variable depth bridge deck, the depth of continuous multi­span bridge deck is increased in pier supports and this absorbs sagging moments in the ... of arches and curved soffit rather than boring uniform deck alignment. Reference is made to Brian Pritchard (1992).

How do engineer determine the number of cells for concrete box girder bridges?

Description : How do engineer determine the number of cells for concrete box girder bridges?

Last Answer : If the depth of a box girder bridge exceeds 1/6 or 1/5 of the bridge width, then it is recommended to be designed as a single cell box girder bridge. However, if the bridge depth is ... improvement in transverse load distribution when the number of cells of box girder is increased to three or more.

Should raking piles of a bridge abutment be placed under an embankment?

Description : Should raking piles of a bridge abutment be placed under an embankment?

Last Answer : For a bridge abutment to be supported on raking piles with different orientations, the movement between the ground and the pile group is difficult to predict. For instance, if some of the raking ... experience severe bending moment and damage the piles as recommended by Dr. Edmund C Hambly (1979).

What are the shortcomings of grillage analysis which is commonly used in structural analysis of bridges?

Description : What are the shortcomings of grillage analysis which is commonly used in structural analysis of bridges?

Last Answer : Grillage analysis suffers from the following shortcomings based on E. C. Hambly: (i) For coarse mesh, torques may not be identical in orthogonal directions. Similarly, twists may differ in ... moment in an element depends on the curvatures in the beam's direction and its orthogonal direction.

In joints of precast concrete bridge segments, what are the functions of applying epoxy adhesive?

Description : In joints of precast concrete bridge segments, what are the functions of applying epoxy adhesive?

Last Answer : Epoxy adhesive is applied in these joints for the following purposes according to International Road Federation (1977): (i) It seals up the joints completely between precast concrete segments to protect the ... in transferring of shear between the joints in case a large single shear key is used.

What are the functions of grout inside tendon ducts?

Description : What are the functions of grout inside tendon ducts?

Last Answer : Grout in prestressing works serves the following purposes: (i) Protect the tendon against corrosion. (ii) Improve the ultimate capacity of tendon. (iii) Provide a bond between the structural member and the tendon. (iv) In case of failure, the anchorage is not subject to all strain energy.

In the design of a simply supported skew bridge, which direction of reinforcement should be provided?

Description : In the design of a simply supported skew bridge, which direction of reinforcement should be provided?

Last Answer : In the conventional design of steel reinforcement for a simply supported skew bridge, a set of reinforcement is usually placed parallel to free edge while the other set is designed parallel ... ). In this way, considerable savings would be obtained from the orthogonal arrangement of reinforcement.

Why is the span length ratio of end span/approach span to its neighboring inner spans usually about 0.75?

Description : Why is the span length ratio of end span/approach span to its neighboring inner spans usually about 0.75?

Last Answer : From aesthetic point of view, an odd number of spans with a decrease in length in the direction of abutment is desirable. Moreover, spans of equal length are found to be boring. However, the ... the last span in a continuous bridge while approach span refers top the first span of a bridge.

What are the three major types of reinforcement used in prestressing?

Description : What are the three major types of reinforcement used in prestressing?

Last Answer : i) Spalling reinforcement Spalling stresses are established behind the loaded area of anchor blocks and this causes breaking away of surface concrete. These stresses are induced by strain incompatibility with ... of action of the load. Reinforcement is needed to resist these lateral tensile forces.

Are diaphragms necessary in the design of concrete box girder bridges?

Description : Are diaphragms necessary in the design of concrete box girder bridges?

Last Answer : Diaphragms are adopted in concrete box girder bridges to transfer loads from bridge decks to bearings. Since the depth of diaphragms normally exceeds the width by two times, they are usually designed ... In fact, diaphragms also contribute to the provision of torsional restraint to the bridge deck.

In the construction of a two­span bridge (span length = L) by using span­by­span construction, why is a length of about 1.25L bridge segment is constructed in the first phase of construction?

Description : In the construction of a two­span bridge (span length = L) by using span­by­span construction, why is a length of about 1.25L bridge segment is constructed in the first phase of construction?

Last Answer : Basically, there are mainly three reasons for this arrangement: (i) The permanent structure is a statically indeterminate structure. During construction by using span­by­span construction, if the ... 25L from the first pier where there is relatively more space to accommodate prestressing works.

In prestressing work, if more than one wire or strand is included in the same duct, why should all wires/strands be stressed at the same time?

Description : In prestressing work, if more than one wire or strand is included in the same duct, why should all wires/strands be stressed at the same time?

Last Answer : If wires/strands are stressed individually inside the same duct, then those stressed strand/wires will bear against those unstressed ones and trap them. Therefore, the friction of the trapped wires is high and is undesirable.

Sometimes the side of concrete bridges is observed to turn black in colour. What is the reason for this phenomenon?

Description : Sometimes the side of concrete bridges is observed to turn black in colour. What is the reason for this phenomenon?

Last Answer : In some cases, it may be due to the accumulation of dust and dirt. However, for the majority of such phenomenon, it is due to fungus or algae growth on concrete bridges. After rainfall, the ... help to solve this problem. Reference is made to Sandberg Consulting Engineers Report 18380/X/01.

What are the advantages of assigning the central pier and the abutment as fixed piers?

Description : What are the advantages of assigning the central pier and the abutment as fixed piers?

Last Answer : (i) For abutment pier to be assigned as fixed pier while the bridge is quite long, the longitudinal loads due to earthquake are quite large. As the earthquake loads are resisted by fixed piers, the size of ... Therefore, the size of movement joints can be reduced significantly.

In bridge widening projects, the method of stitching is normally employed for connecting existing deck to the new deck. What are the problems associated with this method in terms of shrinkage of concrete?

Description : In bridge widening projects, the method of stitching is normally employed for connecting existing deck to the new deck. What are the problems associated with this method in terms of shrinkage of concrete?

Last Answer : In the method of stitching, it is a normal practice to construct the widening part of the bridge at first and let it stay undisturbed for several months. After that, concreting will then be ... Stitching refers to formation of a segment of bridge deck between an existing bridge and a new bridge.

In incremental launching method of bridge construction, what are the measures adopted to enhance sufficient resistance of the superstructure during the launching process?

Description : In incremental launching method of bridge construction, what are the measures adopted to enhance sufficient resistance of the superstructure during the launching process?

Last Answer : i) During the launching process the leading edge of the superstructure is subject to a large hogging moment. In this connection, steel launching nose typically about 0.6­0.65 times span length is ... . iii)For very long span bridge, temporary piers are provided to limit the cantilever moment.

Under what situation shall engineers use jacking at one end only and from both ends in prestressing work?

Description : Under what situation shall engineers use jacking at one end only and from both ends in prestressing work?

Last Answer : During prestressing operation at one end, frictional losses will occur and the prestressing force decreases along the length of tendon until reaching the other end. These frictional losses include the ... if the total span length is sufficiently long, jacking from both ends should be considered.

Mostly long span rail-cum road bridges are provided with a) rocker & roller bearings b) segmental roller with oil bath* c) Sliding bearings d) centralised bearings

Description : Mostly long span rail-cum road bridges are provided with a) rocker & roller bearings b) segmental roller with oil bath* c) Sliding bearings d) centralised bearings

Last Answer : b) segmental roller with oil bath

Bearings for plate girders are -- a) roller bearing b) sliding bearings c) centralised articulated bearings* d) None of the above

Description : Bearings for plate girders are -- a) roller bearing b) sliding bearings c) centralised articulated bearings* d) None of the above

Last Answer : c) centralised articulated bearings*

Prismatic compass is considered more accurate than a surveyor's compass, because (A) It is provided with a better magnetic needle (B) It is provided with a sliding glass in the object vane (C) Its graduations are in whole circle bearings (D) It is provided with a prism to facilitate reading of its graduated circle

Description : Prismatic compass is considered more accurate than a surveyor's compass, because (A) It is provided with a better magnetic needle (B) It is provided with a sliding glass in the object vane ( ... whole circle bearings (D) It is provided with a prism to facilitate reading of its graduated circle

Last Answer : (D) It is provided with a prism to facilitate reading of its graduated circle

The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Description : The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Last Answer : (d) all the mentioned

In sliding contact bearings, a positive pressure can be built up and a load supported by a fluid only by the use of a: [IES-2005] (a) Diverging film (b) Converging-diverging film (c) Converging film (d) Flat film

Description : In sliding contact bearings, a positive pressure can be built up and a load supported by a fluid only by the use of a: [IES-2005] (a) Diverging film (b) Converging-diverging film (c) Converging film (d) Flat film

Last Answer : (c) Converging film

Sliding contact bearings, also called plain bearings have no problem of wear. a) True b) False

Description : Sliding contact bearings, also called plain bearings have no problem of wear. a) True b) False

Last Answer : b) False

If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. check the bearing insulating block on one end of the unit C. replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Description : If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. ... replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Last Answer : Answer: B

In the illustrated motor, roller bearings are used because __________. EL-0001 A. of their ability to absorb moderate thrust loads B. they electrically insulate the rotor from the frame reducing cross-currents C. the shafting and end bells do not require as close a tolerance to properly fit this type of bearing D. the clearance between the rotor and stator is generally as close as mechanical tolerance will permit

Description : In the illustrated motor, roller bearings are used because __________. EL-0001 A. of their ability to absorb moderate thrust loads B. they electrically insulate the rotor from the frame reducing ... clearance between the rotor and stator is generally as close as mechanical tolerance will permit

Last Answer : Answer: D

When removing ball or roller bearings from the shaft of a motor, you should use a _____________. A. rawhide hammer B. brass mallet C. wheel puller D. soft iron pry bar

Description : When removing ball or roller bearings from the shaft of a motor, you should use a _____________. A. rawhide hammer B. brass mallet C. wheel puller D. soft iron pry bar

Last Answer : Answer: C

Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Description : Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Last Answer : (d) None of the mentioned

The piston pin bearings in heavy-duty diesel engines are (a) needle roller bearings (b) tapered roller bearings (c) spherical roller bearings (d) cylindrical roller bearings

Description : The piston pin bearings in heavy-duty diesel engines are (a) needle roller bearings (b) tapered roller bearings (c) spherical roller bearings (d) cylindrical roller bearings

Last Answer : (a) needle roller bearings

Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Last Answer : (d) All of the listed

The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Description : The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Last Answer : (b) separable

Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity

Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Description : Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Last Answer : (c) Cylindrical (straight) roller bearing

Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Description : Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Last Answer : (c) Spherical roller thrust bearings and taper roller bearings

In standard taper roller bearings, the angle of taper of the outer raceway is (a) 5° (b) 8° (c) 15° (d) 25°

Description : In standard taper roller bearings, the angle of taper of the outer raceway is (a) 5° (b) 8° (c) 15° (d) 25°

Last Answer : (d) 25°

Antifriction bearings are (a) thick lubricated bearings (b) plastic bearings (c) ball and roller bearings (d) thin lubricated bearings

Description : Antifriction bearings are (a) thick lubricated bearings (b) plastic bearings (c) ball and roller bearings (d) thin lubricated bearings

Last Answer : (c) ball and roller bearings

The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Description : The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Last Answer : (c) both radial and axial loads

Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller bearing 3. Thrust load only D. Angular contact ball bearing 4. Medium to low radial and thrust combined A B C D A B C D (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Description : Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller ... (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Last Answer : (a) 2 3 1 4

Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Description : Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Last Answer : d) All of the listed

What is the main advantage of hydrodynamic bearing over roller bearing? (a) Easy to assemble [IES-2005] (b) Relatively low price (c) Superior load carrying capacity at higher speeds (d) Less frictional resistance

Description : What is the main advantage of hydrodynamic bearing over roller bearing? (a) Easy to assemble [IES-2005] (b) Relatively low price (c) Superior load carrying capacity at higher speeds (d) Less frictional resistance

Last Answer : (c) Superior load carrying capacity at higher speeds

The maximum frictional force which comes into play when a body just begins to slide over another surface is called (A) Limiting friction (B) Sliding friction (C) Rolling friction (D) Kinematic friction

Description : The maximum frictional force which comes into play when a body just begins to slide over another surface is called (A) Limiting friction (B) Sliding friction (C) Rolling friction (D) Kinematic friction

Last Answer : (A) Limiting friction

The minimum range for sliding the focusing lens in the internal focusing telescope for focusing at all distances beyond 4 m is (A) 5 mm (B) 10 mm (C) 15 mm (D) 20 mm

Description : The minimum range for sliding the focusing lens in the internal focusing telescope for focusing at all distances beyond 4 m is (A) 5 mm (B) 10 mm (C) 15 mm (D) 20 mm 

Last Answer : (D) 20 mm 

In an internal focusing telescope (A) The objective is at a fixed distance from the diaphragm (B) The focusing is done by the sliding of a divergent lens (C) The focusing divergent lens is situated at about the middle of the tube (D) All the above

Description : In an internal focusing telescope (A) The objective is at a fixed distance from the diaphragm (B) The focusing is done by the sliding of a divergent lens (C) The focusing divergent lens is situated at about the middle of the tube (D) All the above

Last Answer : (D) All the above

Pick up wrong statement about friction force for dry surfaces. Friction force is (A) Proportional to normal load between the surfaces (B) Dependent on the materials of contact surface (C) Proportional to velocity of sliding (D) Independent of the area of contact surfaces

Description : Pick up wrong statement about friction force for dry surfaces. Friction force is  (A) Proportional to normal load between the surfaces  (B) Dependent on the materials of contact surface  (C) Proportional to velocity of sliding  (D) Independent of the area of contact surfaces 

Last Answer : (C) Proportional to velocity of sliding 

The ratio of limiting friction and normal reaction is known as (A) Coefficient of friction (B) Angle of friction (C) Angle of repose (D) Sliding friction

Description : The ratio of limiting friction and normal reaction is known as (A) Coefficient of friction (B) Angle of friction (C) Angle of repose (D) Sliding friction

Last Answer : (A) Coefficient of friction