In a transmission line, if the maximum current to minimum current ratio is 2:1 what is the ratio of the maximum voltage to minimum voltage? A. 4:1 B. 1:2 C. 1:4 D. 2:1

In a transmission line, if the maximum current to minimum current ratio is 2:1 what is the
ratio of the maximum voltage to minimum voltage?
A. 4:1
B. 1:2
C. 1:4
D. 2:1
by

1 Answer

Answer :

D. 2:1
by

Related questions

Transmission line must be matched to the load to A. transfer maximum voltage to the load B. transfer maximum current to the load C. reduce the load current D. transfer maximum power to the load

Description : Transmission line must be matched to the load to A. transfer maximum voltage to the load B. transfer maximum current to the load C. reduce the load current D. transfer maximum power to the load

Last Answer : D. transfer maximum power to the load

Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Last Answer : D. The standing wave ratio is one.

At the ends of a half-wave antenna, what values of current and voltage exist compared to the remainder of the antenna? A. Minimum voltage and minimum current B. Equal voltage and current C. Minimum voltage and maximum current D. Maximum voltage and minimum current.

Description : At the ends of a half-wave antenna, what values of current and voltage exist compared to the remainder of the antenna? A. Minimum voltage and minimum current B. Equal voltage and current C. Minimum voltage and maximum current D. Maximum voltage and minimum current.

Last Answer : D. Maximum voltage and minimum current.

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Description : An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Last Answer : B. Either A or C

What is the ratio of the maximum radiation intensity to the average radiation intensity? A. Aperture gain B. Directivity gain C. Transmission gain D. Power gain

Description : What is the ratio of the maximum radiation intensity to the average radiation intensity? A. Aperture gain B. Directivity gain C. Transmission gain D. Power gain

Last Answer : B. Directivity gain

It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Description : It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Last Answer : A. when comparing the gains of directional antennas

When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern hemisphere) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Last Answer : A. When comparing the gains of directional antennas

What is the meaning of the term “velocity factor” of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial cable. C. The velocity of the wave on the transmission line multiplied by the velocity of light in a vacuum. D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of light in vacuum C. The ratio of the characteristic impedance of the line to the terminating impedance D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Description : What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Description : The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Last Answer : A. 1

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

A pair of current-carrying conductors is not considered a transmission line unless it is at least ___ λ long at the signal frequency. A. 0.1 B. 0.3 C. 0.2 D. 0.4

Description : A pair of current-carrying conductors is not considered a transmission line unless it is at least ___ λ long at the signal frequency. A. 0.1 B. 0.3 C. 0.2 D. 0.4

Last Answer : A. 0.1

What is the maximum theoretical data rate of the above problem if one transponder is used for binary transmission? A. 36 Mbps B. 72 Mbps C.18 Mbps D. 144 Mbps

Description : What is the maximum theoretical data rate of the above problem if one transponder is used for binary transmission? A. 36 Mbps B. 72 Mbps C.18 Mbps D. 144 Mbps

Last Answer : B. 72 Mbps

Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Description : Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Last Answer : B. The location of the antenna with respect to nearby objects

What is driven element? A. Always the rearmost element B. Always the forward most element C. The element fed by the transmission line D. The element connected to the rotator

Description : What is driven element? A. Always the rearmost element B. Always the forward most element C. The element fed by the transmission line D. The element connected to the rotator

Last Answer : C. The element fed by the transmission line

A component that samples the microwave signal travelling in one direction down to the transmission line A. Isolator B. Combiner C. Directional coupler D. Attenuator

Description : A component that samples the microwave signal travelling in one direction down to the transmission line A. Isolator B. Combiner C. Directional coupler D. Attenuator

Last Answer : C. Directional coupler

What distortion is not caused by transmission line characteristics? A. Phase distortion B. Pulse shape distortion C. Spacing bias distortion D. Amplitude distortion

Description : What distortion is not caused by transmission line characteristics? A. Phase distortion B. Pulse shape distortion C. Spacing bias distortion D. Amplitude distortion

Last Answer : C. Spacing bias distortion

What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Description : What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Last Answer : B. A specially configured coaxial transmission line

In transmission line, which of the following is the first step in the procedure of using stub matching? A. Calculate stub susceptance. B. Calculate load admittance C. Connect stub to load D. Transform conductance to resistance

Description : In transmission line, which of the following is the first step in the procedure of using stub matching? A. Calculate stub susceptance. B. Calculate load admittance C. Connect stub to load D. Transform conductance to resistance

Last Answer : B. Calculate load admittance

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150Ω D. 2 Ω

Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω

Last Answer : C. 150 Ω

What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Description : What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Last Answer : A. 0.25

What is the propagation velocity of a signal in a transmission line whose inductance and capacitance are 5μH/m and 20μF/m respectively? A. 100x103 m/s B. 100 m/s C. 10x103 m/s D. 100x106 m/s

Description : What is the propagation velocity of a signal in a transmission line whose inductance and capacitance are 5μH/m and 20μF/m respectively? A. 100x103 m/s B. 100 m/s C. 10x103 m/s D. 100x106 m/s

Last Answer : A. 100x103 m/s

Which of the following is considered the most frequently used transmission line? A. Two-wire open line B. Twin lead C. Rigid coaxial line D. Flexible coaxial line

Description : Which of the following is considered the most frequently used transmission line? A. Two-wire open line B. Twin lead C. Rigid coaxial line D. Flexible coaxial line

Last Answer : D. Flexible coaxial line

A coaxial cable has 7dB of reflected power when the input is 5 watts. What is the output of the transmission line? A. 5 watts B. 2.5 watts C. 1.25 watts D. 1 watt

Description : A coaxial cable has 7dB of reflected power when the input is 5 watts. What is the output of the transmission line? A. 5 watts B. 2.5 watts C. 1.25 watts D. 1 watt

Last Answer : D. 1 watt

What would be the physical length of a tpical coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz? A. 20 meters B. 3.51 meters C. 2.33 meters D. 0.25 meter

Description : What would be the physical length of a tpical coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz? A. 20 meters B. 3.51 meters C. 2.33 meters D. 0.25 meter

Last Answer : B. 3.51 meters

Why is the physical length of a coaxial cable transmission line shorter than its electrical length?A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the coaxial cable C. The surge impedance is higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Description : Why is the physical length of a coaxial cable transmission line shorter than its electrical length? A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the ... higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Last Answer : B. RF energy moves slower along the coaxial cable

What determines the velocity factor in a transmission line? A. The termination impedance B. The line length C. Dielectrics in the line D. The center conductor resistivity

Description : What determines the velocity factor in a transmission line? A. The termination impedance B. The line length C. Dielectrics in the line D. The center conductor resistivity

Last Answer : C. Dielectrics in the line

If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Description : What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Last Answer : D. Radiation resistance plus ohmic resistance

A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Description : A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Last Answer : D. 112 Ω

A properly matched transmission line has a loss of 1.5 dB/100m. if 10 W is supplied to one end of the line, how many watts reach the load, 27 m away? A. 10 W B. 7.2 W C. 9.9 W D. 9.1 W

Description : A properly matched transmission line has a loss of 1.5 dB/100m. if 10 W is supplied to one end of the line, how many watts reach the load, 27 m away? A. 10 W B. 7.2 W C. 9.9 W D. 9.1 W

Last Answer : D. 9.1 W

What do you call a transmission line used specifically for the purpose of achieving delay? A. Delay line B. Flat line C. Resonant line D. Non-resonant line

Description : What do you call a transmission line used specifically for the purpose of achieving delay? A. Delay line B. Flat line C. Resonant line D. Non-resonant line

Last Answer : A. Delay line

What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Description : What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Last Answer : C. 75 ns

What is the physical length of the above transmission line at 3/8λ long? A.0.82 m B. 0.82 ft C. 0.82 in D. 0.82 cm

Description : What is the physical length of the above transmission line at 3/8λ long? A.0.82 m B. 0.82 ft C. 0.82 in D. 0.82 cm

Last Answer : B. 0.82 ft

If the operating frequency is 450 MHz what length of a pair of conductors is considered to be a transmission line? A. 2.19 ft B. 2.19 m C. 0.219 ft D. 0.219 m

Description : If the operating frequency is 450 MHz what length of a pair of conductors is considered to be a transmission line? A. 2.19 ft B. 2.19 m C. 0.219 ft D. 0.219 m

Last Answer : C. 0.219 ft

Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Description : Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Last Answer : B. 120 ohms

A transmission line consisting of two conductors that have equal resistance per unit length. A. Unbalanced line B. Open-wire line C. Balanced line D. Coaxial line

Description : A transmission line consisting of two conductors that have equal resistance per unit length. A. Unbalanced line B. Open-wire line C. Balanced line D. Coaxial line

Last Answer : C. Balanced line

Which of the following determines the characteristics of a transmission line? A. Inductance B. Capacitance C. Physical dimension D. Length

Description : Which of the following determines the characteristics of a transmission line? A. Inductance B. Capacitance C. Physical dimension D. Length

Last Answer : C. Physical dimension

What determines the velocity factor in transmission line? A. The center conductor resistivity B. Dielectrics in the line C. The termination impedance D. The line length

Description : What determines the velocity factor in transmission line? A. The center conductor resistivity B. Dielectrics in the line C. The termination impedance D. The line length

Last Answer : B. Dielectrics in the line

Best choice of transmission line component to couple a coaxial line to a parallel-wire line A. Shorting B. Balun C. Slotted line D. Directional coupler

Description : Best choice of transmission line component to couple a coaxial line to a parallel-wire line A. Shorting B. Balun C. Slotted line D. Directional coupler

Last Answer : B. Balun

Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Description : Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Last Answer : B. 6 dB

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

What is a driven element of an antenna? A. Always the rearmost element B. Always the forwardmost element C. The element fed by the transmission line D. The element connected to the rotator

Description : What is a driven element of an antenna? A. Always the rearmost element B. Always the forwardmost element C. The element fed by the transmission line D. The element connected to the rotator

Last Answer : C. The element fed by the transmission line

Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Description : Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Last Answer : B. Velocity factor

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR

Description : The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR

Last Answer : B. Input and output

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

A device that radiates electromagnetic energy and or intercepts electromagnetic radation. A. Antenna B. Transmitter C. Transmission line D. Transceiver

Description : A device that radiates electromagnetic energy and or intercepts electromagnetic radation. A. Antenna B. Transmitter C. Transmission line D. Transceiver

Last Answer : A. Antenna