Which stands for dB relative level? A. dBrn B. dBm C. dBr D. dBa

Which stands for dB relative level?
A. dBrn
B. dBm
C. dBr
D. dBa
by

1 Answer

Answer :

C. dBr
by

Related questions

What is the unit of noise power of psophometer? A. pWp B. dBa C. dBm D. dBrn

Description : What is the unit of noise power of psophometer? A. pWp B. dBa C. dBm D. dBrn

Last Answer : A. pWp

What is the reference tone level for dBrn? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Description : What is the reference tone level for dBrn? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Last Answer : A. -90 dBm

Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Description : Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Last Answer : C. dBmc

Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Description : Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Last Answer : D. B and C above

The most common unit of noise measurement in white noise voltage testing. A. NPR B. dBm C. dBW D. dBrn

Description : The most common unit of noise measurement in white noise voltage testing. A. NPR B. dBm C. dBW D. dBrn

Last Answer : A. NPR

What is the reference tone level for dBa? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Description : What is the reference tone level for dBa? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Last Answer : D. -85 dBm

At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm

Description : At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm

Last Answer : D. -90 dBm

Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Description : Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Last Answer : A. 75

You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Last Answer : D. 32

You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Description : You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Last Answer : C. 35

You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Description : You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Last Answer : C. 22

In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Last Answer : B. 93

ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB

Description : ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB

Last Answer : B. -90 dBm

15 dBa F1A weighted, equals ___________. A. -90 dBm B. -82 dBm C. -85 dBm D. -70 dBm

Description : 15 dBa F1A weighted, equals ___________. A. -90 dBm B. -82 dBm C. -85 dBm D. -70 dBm

Last Answer : D. -70 dBm

Unit of noise power of psophometer A. dBa B. pWp C. dBm D. dBmO

Description : Unit of noise power of psophometer A. dBa B. pWp C. dBm D. dBmO

Last Answer : B. pWp

Noise reduction system used for film sound in movie A. dBx B. dolby C. dBa D. dBm

Description : Noise reduction system used for film sound in movie A. dBx B. dolby C. dBa D. dBm

Last Answer : B. dolby

A reading of -50 dBm on the disturbing pair, and -80 on the disturbed pair equals _____ dB of crosstalk coupling. A. 20 B. 30 C. 60 D. 25

Description : A reading of -50 dBm on the disturbing pair, and -80 on the disturbed pair equals _____ dB of crosstalk coupling. A. 20 B. 30 C. 60 D. 25

Last Answer : B. 30

The standard test tone A. 0dB B. 10 dBm C. 0 dBm D. 10 dB

Description : The standard test tone A. 0dB B. 10 dBm C. 0 dBm D. 10 dB

Last Answer : C. 0 dBm

A practical dBrn measurement will almost always in a _______ number. A. positive B. negative C. imaginary D. fractional

Description : A practical dBrn measurement will almost always in a _______ number. A. positive B. negative C. imaginary D. fractional

Last Answer : A. positive

Reading a 58 dBrn, at a +7 test point is equal to ________ dBa0. A. 26 B. 65 C. 51 D. 46

Description : Reading a 58 dBrn, at a +7 test point is equal to ________ dBa0. A. 26 B. 65 C. 51 D. 46

Last Answer : D. 46

What is the reference level for noise measurement, F1A weighted? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Description : What is the reference level for noise measurement, F1A weighted? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Last Answer : D. -85 dBm

The difference between signal strength at a given point and a reference level is________. A. power B. dBm C. level D. ratio

Description : The difference between signal strength at a given point and a reference level is________. A. power B. dBm C. level D. ratio

Last Answer : C. level

What is the reference noise level? A. 10 pW B. 0 dBm C. 1mW D. -90 dBm

Description : What is the reference noise level? A. 10 pW B. 0 dBm C. 1mW D. -90 dBm

Last Answer : D. -90 dBm

ECE Board Exam March 1996 What is the reference tone level for dBm? A. -82 dBm B. -85 dBm C. -67 dBm D. -90 dBm

Description : ECE Board Exam March 1996 What is the reference tone level for dBm? A. -82 dBm B. -85 dBm C. -67 dBm D. -90 dBm

Last Answer : D. -90 dBm

The sound intensity received from the nearby jet plane is 12.6 µW/m2 and that from another jet plane some distance away is 0.45 µW/m2 . Find the relative loudness of the two. A. 14.0 dB B. 14.5dB C. 12.5 D. 14.5

Description : The sound intensity received from the nearby jet plane is 12.6 µW/m2 and that from another jet plane some distance away is 0.45 µW/m2 . Find the relative loudness of the two. A. 14.0 dB B. 14.5dB C. 12.5 D. 14.5

Last Answer : B. 14.5dB

In reference to dB meters, 0 dBm represents 1 milliwatt into what value of load?

Description : In reference to dB meters, 0 dBm represents 1 milliwatt into what value of load?

Last Answer : 600-ohm load.

For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Description : For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Last Answer : ∙ C. -35 dBm

A measurement of -75 dBm, C-message weighted, would be _________ dBrnc. A. 8 B. 7 C. 9 D. 15

Description : A measurement of -75 dBm, C-message weighted, would be _________ dBrnc. A. 8 B. 7 C. 9 D. 15

Last Answer : D. 15

F1A weighting refers to ___________. A. -90 dBm B. dBrnc0 C. dBrnc D. F1A handset

Description : F1A weighting refers to ___________. A. -90 dBm B. dBrnc0 C. dBrnc D. F1A handset

Last Answer : C. dBrnc

What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36

Description : What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36

Last Answer : A. 1.09

The most common unit of noise measurement in white noise testing. A. dBw B. dBk C. dBm D. NPR

Description : The most common unit of noise measurement in white noise testing. A. dBw B. dBk C. dBm D. NPR

Last Answer : D. NPR

What is the equivalent output of a circuit in dBm, if it is has an output of 10 watts? A. 10 dBm B. 30 dBm C. 20 dBm D. 40 dBm

Description : What is the equivalent output of a circuit in dBm, if it is has an output of 10 watts? A. 10 dBm B. 30 dBm C. 20 dBm D. 40 dBm

Last Answer : D. 40 dBm

ECE Board Exam March 1996 Crosstalk coupling is ___________. A. dBm (disturbing pair) minus dBm (disturbed pair) B. the difference between readings on a cable pair with a tone and a cable pair without tone read at the far end of a cable C. signals from one circuit that get into another circuit D. All of these are true

Description : ECE Board Exam March 1996 Crosstalk coupling is ___________. A. dBm (disturbing pair) minus dBm (disturbed pair) B. the difference between readings on a cable pair with a tone and a cable pair without ... a cable C. signals from one circuit that get into another circuit D. All of these are true

Last Answer : D. All of these are true

You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Description : You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Last Answer : C. 25

What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Last Answer : C. 125,000

For a loudness level between 110 and 120 dB, the maximum daily exposure limit is ____ minute (s). A. 1 B. 60 C. 20 D. 45

Description : For a loudness level between 110 and 120 dB, the maximum daily exposure limit is ____ minute (s). A. 1 B. 60 C. 20 D. 45

Last Answer : A. 1

What loudness level in which permanent damage to hearing is possible? A. 120 dB B. 140 dB C. 130 dB D. 150 dB

Description : What loudness level in which permanent damage to hearing is possible? A. 120 dB B. 140 dB C. 130 dB D. 150 dB

Last Answer : D. 150 dB

For the safety and comfort of factory workers, the sound-intensity level in a certain factory must remain below 85 dB. What is the maximum sound intensity allowed in this factory? A. 3.2 x 10-4 W/m2 B. 3.2 x 10-6 W/m2 C. 3.2 x 10-10 W/m2 D. 3.2 x 10-3 W/m2

Description : For the safety and comfort of factory workers, the sound-intensity level in a certain factory must remain below 85 dB. What is the maximum sound intensity allowed in this factory? A. 3.2 x 10-4 W/m2 B. 3.2 x 10-6 W/m2 C. 3.2 x 10-10 W/m2 D. 3.2 x 10-3 W/m2

Last Answer : A. 3.2 x 10-4 W/m2

A choir consisting of 36 individuals all of whom can sing with the same intensity. A soloist sings a certain passage and then is joined by the remainder of the choir members for a repeat of the passage. What is the difference in the sound intensity level in the two cases? A. 3 dB B. 6 dB C. 36 dB D. 15.6dB

Description : A choir consisting of 36 individuals all of whom can sing with the same intensity. A soloist sings a certain passage and then is joined by the remainder of the choir members for a repeat of the passage. What is the ... sound intensity level in the two cases? A. 3 dB B. 6 dB C. 36 dB D. 15.6dB

Last Answer : D. 15.6dB

What increase in sound level is commonly perceived by most people? A. 6 to 10 dB B. 1 to 3 dB C. 3 to 6 dB D. 10 to 20dB

Description : What increase in sound level is commonly perceived by most people? A. 6 to 10 dB B. 1 to 3 dB C. 3 to 6 dB D. 10 to 20dB

Last Answer : A. 6 to 10 dB

At what loudness level do pitch (in mels) and frequency (in Hz) are numerically equal? A. 0 dB B. 20 dB C. 60 dB D. 40 dB

Description : At what loudness level do pitch (in mels) and frequency (in Hz) are numerically equal? A. 0 dB B. 20 dB C. 60 dB D. 40 dB

Last Answer : D. 40 dB

The sound power level of a jet plane flying at a height of 1 km is 160 dB. What is the maximum sound pressure level on the ground directly below the plane assuming that the aircraft radiates sound equally in all directions? A. 59.1 dB B. 69.1 dB C. 79.1 dB D. 89.1 dB

Description : The sound power level of a jet plane flying at a height of 1 km is 160 dB. What is the maximum sound pressure level on the ground directly below the plane assuming that the aircraft radiates sound equally in all directions? A. 59.1 dB B. 69.1 dB C. 79.1 dB D. 89.1 dB

Last Answer : D. 89.1 dB

ECE Board Exam March 1996 A car horn outdoors produces a sound intensity level of 90 dB at 10 ft away. At this distance, what is the sound power in watt? A. 12 W B. 0.12 W C. 0.012 W D. 1.2 W

Description : ECE Board Exam March 1996 A car horn outdoors produces a sound intensity level of 90 dB at 10 ft away. At this distance, what is the sound power in watt? A. 12 W B. 0.12 W C. 0.012 W D. 1.2 W

Last Answer : C. 0.012 W

I've lost some Rollback Segments, how can I get my DB back? (for DBA

Description : I've lost some Rollback Segments, how can I get my DB back? (for DBA

Last Answer : Re-start your database with the following INIT.ORA parameter if one of your rollback segments is corrupted. You can then drop the corrupted rollback segments and create it from scratch. ... Please contact Oracle Support before using it. _Corrupted_rollback_segments = (rbs01, rbs01, rbs03, rbs04)

I've lost my REDOLOG files, how can I get my DB back? (for DBA

Description : I've lost my REDOLOG files, how can I get my DB back? (for DBA

Last Answer : The following INIT.ORA parameter may be required if your current redo logs are corrupted or blown away. Caution is advised when enabling this parameter as you might end-up losing your entire database. Please contact Oracle Support before using it. _allow_resetlogs_corruption = true

You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Description : You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Last Answer : C. 38 dBa

Cable attenuation is usually expressed in terms of a. Loss per foot b. dB/km c. intensity per mile d. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of a. Loss per foot b. dB/km c. intensity per mile d. voltage drop per inch

Last Answer : b. dB/km

What is the gain of an antenna over a half-wavelength dipole when it has 6 dB gain over an isotropic radiator? A. 6.0 dB B. 8.1 dB C. 3.9 dB D. 10.0 dB

Description : What is the gain of an antenna over a half-wavelength dipole when it has 6 dB gain over an isotropic radiator? A. 6.0 dB B. 8.1 dB C. 3.9 dB D. 10.0 dB

Last Answer : C. 3.9 dB

What is the gain, in dB of a helical antenna with diameter of λ/3, 10 turns at pitch of λ/4, used at 100 MHz? A. 16 B. 41.1 C. 31.4 D. 1.25

Description : What is the gain, in dB of a helical antenna with diameter of λ/3, 10 turns at pitch of λ/4, used at 100 MHz? A. 16 B. 41.1 C. 31.4 D. 1.25

Last Answer : A. 16