Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83
Last Answer : B. 93
Description : You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12
Last Answer : C. 22
Description : You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa
Last Answer : C. 38 dBa
Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32
Last Answer : D. 32
Description : You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17
Last Answer : C. 25
Description : A measurement of -75 dBm, C-message weighted, would be _________ dBrnc. A. 8 B. 7 C. 9 D. 15
Last Answer : D. 15
Description : Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31
Last Answer : A. 75
Description : Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB
Last Answer : C. dBmc
Description : At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm
Last Answer : D. -90 dBm
Description : ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB
Last Answer : B. -90 dBm
Description : A reading of -50 dBm on the disturbing pair, and -80 on the disturbed pair equals _____ dB of crosstalk coupling. A. 20 B. 30 C. 60 D. 25
Last Answer : B. 30
Description : What is the reference level for noise measurement, F1A weighted? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm
Last Answer : D. -85 dBm
Description : Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above
Last Answer : D. B and C above
Description : Reading a 58 dBrnC on your Western Electric 3A test set at a +7 test point is equal to ______ dBrnc0. A. 58 B. 51 C. 65 D. 27
Last Answer : B. 51
Description : F1A weighting refers to ___________. A. -90 dBm B. dBrnc0 C. dBrnc D. F1A handset
Last Answer : C. dBrnc
Description : The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB
Last Answer : D. 14 dB
Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV
Last Answer : A. 0.5 mV
Description : The standard test tone A. 0dB B. 10 dBm C. 0 dBm D. 10 dB
Last Answer : C. 0 dBm
Description : Which stands for dB relative level? A. dBrn B. dBm C. dBr D. dBa
Last Answer : C. dBr
Description : The noise from an airplane engine 100 ft from an observer is found to have an intensity of 45dB. What will be the intensity when the plane flies overhead at an altitude of 1 mi? A. 10.5 dB B. 34.5 dB C. 35 dB D. 20.5 dB
Last Answer : A. 10.5 dB
Description : 15 dBa F1A weighted, equals ___________. A. -90 dBm B. -82 dBm C. -85 dBm D. -70 dBm
Last Answer : D. -70 dBm
Description : For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm
Last Answer : ∙ C. -35 dBm
Description : What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36
Last Answer : A. 1.09
Description : What is the reference noise level? A. 10 pW B. 0 dBm C. 1mW D. -90 dBm
Description : When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?
Last Answer : Attenuations of the directional coupler and the connecting cable.
Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts
Last Answer : B. 2.656 watts
Last Answer : A. PAM
Description : What is the unit of noise power of psophometer? A. pWp B. dBa C. dBm D. dBrn
Last Answer : A. pWp
Description : The most common unit of noise measurement in white noise voltage testing. A. NPR B. dBm C. dBW D. dBrn
Last Answer : A. NPR
Description : Unit of noise power of psophometer A. dBa B. pWp C. dBm D. dBmO
Last Answer : B. pWp
Description : The most common unit of noise measurement in white noise testing. A. dBw B. dBk C. dBm D. NPR
Last Answer : D. NPR
Description : Noise reduction system used for film sound in movie A. dBx B. dolby C. dBa D. dBm
Last Answer : B. dolby
Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone
Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz
Description : What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB
Last Answer : C. 40 dB
Description : The signal to noise ratio that is required for a satisfactory television reception. A. 30 dB B. 40 dB C. 10 dB D. 20 dB
Last Answer : B. 40 dB
Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB
Last Answer : D. 8.8 dB
Description : What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB
Last Answer : A. 50 dB
Description : The difference between signal strength at a given point and a reference level is________. A. power B. dBm C. level D. ratio
Last Answer : C. level
Description : Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB
Last Answer : A. 1.6 dB
Description : Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?
Last Answer : 35-dB RMS because the highest SNR can always record and reproduce the widest range of input signals.
Description : Ajay reads at an average rate of 30 pages per hour, while Vikram reads at an average rate of 40 pages per hour. If Ajay starts reading a novel at 4:30 PM and Vikram begins reading an identical copy of the same book at 5:20 PM, at ... same page? a) 7:50 PM b) 8:15 PM c) 8:40 PM d) 9:00 PM e) 9:25 PM
Last Answer : Ajay reads at average rate of 30 pages per hour ie. 1 page in every two minutes. Therefore, by 5:20 PM, he would have covered 25 pages By 6:20 PM, Ajay would have read 25+30 pages and Vikram would have ... and he will also finish 100 pages Hence, both of them will be on same page at 7:50 Answer: a)
Description : A dumpy level was set up at mid-point between pegs A and B, 80 m apart and the staff readings were 1.32 and 1.56. When the level was set up at a point 10 m from A on BA produced, the staff readings obtained at A ... this set up at S should be (A) 1.435 (B) 1.345 (C) 1.425 (D) None of these
Last Answer : (B) 1.345
Description : Acceptable "Noise Pollution Level" in India range between: (1) 16 - 35 db (2) 40 - 45 db (3) 70 - 100 db (4) 10 - 15 db
Last Answer : (2) 40 - 45 db Explanation: According to the noise pollution rules, the permissible noise level during the day is 50dB in silence zones, 55dB in residential areas, 65 dB in commercial areas and 75 ... areas, commercial areas and industrial areas are respectively 40 dB, 45 dB, 55 dB and 70 dB.
Description : The agreed standard for measuring loudness is the loudness sensation produced by a 1000 Hz sine wave _____ dB above the listener’s threshold of hearing. A. 80 B. 50 C. 30 D. 40
Last Answer : D. 40
Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000
Last Answer : C. 125,000
Description : What is the reference tone level for dBa? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm
Description : What is the reference tone level for dBrn? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm
Last Answer : A. -90 dBm
Description : ECE Board Exam March 1996 What is the reference tone level for dBm? A. -82 dBm B. -85 dBm C. -67 dBm D. -90 dBm
Description : What is the equivalent output of a circuit in dBm, if it is has an output of 10 watts? A. 10 dBm B. 30 dBm C. 20 dBm D. 40 dBm
Last Answer : D. 40 dBm
Description : The noise figure of the first circuit in tandem connection is 10.5 dB while its power gain is 15, what is the over all noise figure if the second circuit has a noise figure of 11 dB? A. 11.59 dB B. 11.23 dB C. 10.79 dB D. 10.5 dB
Last Answer : C. 10.79 dB