Description : What is the unit of noise power of psophometer? A. pWp B. dBa C. dBm D. dBrn
Last Answer : A. pWp
Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83
Last Answer : B. 93
Description : Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB
Last Answer : C. dBmc
Description : Noise reduction system used for film sound in movie A. dBx B. dolby C. dBa D. dBm
Last Answer : B. dolby
Description : ___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter
Last Answer : A. Psophometer
Description : What is the reference tone level for dBa? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm
Last Answer : D. -85 dBm
Description : 15 dBa F1A weighted, equals ___________. A. -90 dBm B. -82 dBm C. -85 dBm D. -70 dBm
Last Answer : D. -70 dBm
Description : Which stands for dB relative level? A. dBrn B. dBm C. dBr D. dBa
Last Answer : C. dBr
Description : The most common unit of noise measurement in white noise voltage testing. A. NPR B. dBm C. dBW D. dBrn
Last Answer : A. NPR
Description : The most common unit of noise measurement in white noise testing. A. dBw B. dBk C. dBm D. NPR
Last Answer : D. NPR
Description : What is the reference level for noise measurement, F1A weighted? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm
Description : Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above
Last Answer : D. B and C above
Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32
Last Answer : D. 32
Description : What is the reference noise level? A. 10 pW B. 0 dBm C. 1mW D. -90 dBm
Last Answer : D. -90 dBm
Description : What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36
Last Answer : A. 1.09
Description : You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25
Last Answer : C. 35
Description : You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa
Last Answer : C. 38 dBa
Description : At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm
Description : The difference between signal strength at a given point and a reference level is________. A. power B. dBm C. level D. ratio
Last Answer : C. level
Description : ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB
Last Answer : B. -90 dBm
Description : What is the reference tone level for dBrn? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm
Last Answer : A. -90 dBm
Description : Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31
Last Answer : A. 75
Description : A measurement of -75 dBm, C-message weighted, would be _________ dBrnc. A. 8 B. 7 C. 9 D. 15
Last Answer : D. 15
Description : A reading of -50 dBm on the disturbing pair, and -80 on the disturbed pair equals _____ dB of crosstalk coupling. A. 20 B. 30 C. 60 D. 25
Last Answer : B. 30
Description : F1A weighting refers to ___________. A. -90 dBm B. dBrnc0 C. dBrnc D. F1A handset
Last Answer : C. dBrnc
Description : The standard test tone A. 0dB B. 10 dBm C. 0 dBm D. 10 dB
Last Answer : C. 0 dBm
Description : You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12
Last Answer : C. 22
Description : What is the equivalent output of a circuit in dBm, if it is has an output of 10 watts? A. 10 dBm B. 30 dBm C. 20 dBm D. 40 dBm
Last Answer : D. 40 dBm
Description : ECE Board Exam March 1996 What is the reference tone level for dBm? A. -82 dBm B. -85 dBm C. -67 dBm D. -90 dBm
Description : ECE Board Exam March 1996 Crosstalk coupling is ___________. A. dBm (disturbing pair) minus dBm (disturbed pair) B. the difference between readings on a cable pair with a tone and a cable pair without ... a cable C. signals from one circuit that get into another circuit D. All of these are true
Last Answer : D. All of these are true
Description : The water content between Field capacity (-1/3 bar) to PWP (-15 bar) is called
Last Answer : Ans.Available water
Description : pF value is zero of — a. Field capacity b. PWP c. Oven dry soil d. Saturated soil
Last Answer : d. Saturated soil
Description : Which of the following is not a way of minimizing if not eliminating noise? A. Use redundancy B. Increase transmitted power C. Reduce signaling rate D. Increase channel bandwidth
Last Answer : D. Increase channel bandwidth
Description : The total noise power present in a 1-Hz bandwidth . A. Noise density B. Noise figure C. Noise limit D. Noise intensity
Last Answer : A. Noise density
Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source
Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals
Description : The value of the resistor creating thermal noise is doubled. The noise power generated is therefore. A. halved B. quadrupled C. doubled D. unchanged
Last Answer : D. unchanged
Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.
Last Answer : C. A random voltage across the resistor does not exist
Description : The noise figure of the first circuit in tandem connection is 10.5 dB while its power gain is 15, what is the over all noise figure if the second circuit has a noise figure of 11 dB? A. 11.59 dB B. 11.23 dB C. 10.79 dB D. 10.5 dB
Last Answer : C. 10.79 dB
Description : Man-made noise is usually from _______. A. transmission over power lines and by ground wave B. sky-wave C. space-wave D. troposphere
Last Answer : A. transmission over power lines and by ground wave
Description : What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver
Last Answer : C. The noise floor of the receiver
Description : What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz
Last Answer : B. 3853 Hz
Description : A major and basic advantage for the use of a klystron. A. High power B. Efficiency C. Lesser noise D. Cheaper
Last Answer : A. High power
Description : A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor
Last Answer : A. Noise equivalent power
Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone
Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz
Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity
Last Answer : A. increases sensitivity to weak signals
Description : Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry
Last Answer : D. wave traps in the antenna circuitry
Description : Which of the following low noise transistors is commonly used at microwave frequencies? A. MOSFET B. GASFET C. MESFET D. JFET
Last Answer : C. MESFET
Description : The major cause of atmospheric or static noise are A. Thunderstorms B. Airplanes C. Meteor showers D. All of these
Last Answer : A. Thunderstorms
Description : What do you call the noise coming from the sun and stars? A. Black-body noise B. Space noise C. Galactic noise D. All of these
Last Answer : B. Space noise
Description : What is the primary cause of atmospheric noise? A. Thunderstorm B. Lightning C. Thunderstorm and lightning D. Weather condition
Last Answer : B. Lightning