You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting
network and a flat meter. Your meter reads -47dBm. What is this reading in dBa?
A. 77 dBa
B. 35 dBa
C. 38 dBa
D. 32 dBa
by

1 Answer

Answer :

C. 38 dBa
by

Related questions

You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Last Answer : D. 32

You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Description : You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Last Answer : C. 25

In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Last Answer : B. 93

You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Description : You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Last Answer : C. 35

You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Description : You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Last Answer : C. 22

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

F1A weighting refers to ___________. A. -90 dBm B. dBrnc0 C. dBrnc D. F1A handset

Description : F1A weighting refers to ___________. A. -90 dBm B. dBrnc0 C. dBrnc D. F1A handset

Last Answer : C. dBrnc

15 dBa F1A weighted, equals ___________. A. -90 dBm B. -82 dBm C. -85 dBm D. -70 dBm

Description : 15 dBa F1A weighted, equals ___________. A. -90 dBm B. -82 dBm C. -85 dBm D. -70 dBm

Last Answer : D. -70 dBm

The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant, what does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

What is the reference level for noise measurement, F1A weighted? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Description : What is the reference level for noise measurement, F1A weighted? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Last Answer : D. -85 dBm

Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Description : Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Last Answer : D. B and C above

The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Description : The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Last Answer : D. 14 dB

Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Description : Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Last Answer : C. dBmc

What is the unit of noise power of psophometer? A. pWp B. dBa C. dBm D. dBrn

Description : What is the unit of noise power of psophometer? A. pWp B. dBa C. dBm D. dBrn

Last Answer : A. pWp

Unit of noise power of psophometer A. dBa B. pWp C. dBm D. dBmO

Description : Unit of noise power of psophometer A. dBa B. pWp C. dBm D. dBmO

Last Answer : B. pWp

Noise reduction system used for film sound in movie A. dBx B. dolby C. dBa D. dBm

Description : Noise reduction system used for film sound in movie A. dBx B. dolby C. dBa D. dBm

Last Answer : B. dolby

A gun barrel of mass 600 Kg has a recoil spring of stiffness 294 KN/m. If the barrel recoils 1.3 m on firing, what will be the initial recoil velocity of the barrel? (A) 28.77 m/s (B) 32.77 m/s (C) 35.77 m/s (D) 40.77 m/s

Description : A gun barrel of mass 600 Kg has a recoil spring of stiffness 294 KN/m. If the barrel recoils 1.3 m on firing, what will be the initial recoil velocity of the barrel? (A) 28.77 m/s (B) 32.77 m/s (C) 35.77 m/s (D) 40.77 m/s

Last Answer : (A) 28.77 m/s

What device measures rf power by measuring the heat the rf power generates? A. Calorimeter B. Goniometer C. Spectrum meter D. Oscilloscope

Description : What device measures rf power by measuring the heat the rf power generates? A. Calorimeter B. Goniometer C. Spectrum meter D. Oscilloscope

Last Answer : A. Calorimeter

One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used

Description : One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used

Last Answer : A. noise is amplified with voice when an FDM system is used

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

What is the channel spacing for MF-HF voice frequencies? A. 2.8 kHz B. 500 Hz C. 3.5 kHz D. 3 kHz

Description : What is the channel spacing for MF-HF voice frequencies? A. 2.8 kHz B. 500 Hz C. 3.5 kHz D. 3 kHz

Last Answer : D. 3 kHz

How do you transmit through multiplexing, a thousand of voice channel information over a single fiber optic using on e wavelength? A. Polar division B. Time division C. Fiber division D. Frequency division

Description : How do you transmit through multiplexing, a thousand of voice channel information over a single fiber optic using on e wavelength? A. Polar division B. Time division C. Fiber division D. Frequency division

Last Answer : B. Time division

Nominal voice channel A. 20 to 20 KHz B. 16 to 16 KHz C. 3 to 3 KHz D. 4 KHz

Description : Nominal voice channel A. 20 to 20 KHz B. 16 to 16 KHz C. 3 to 3 KHz D. 4 KHz

Last Answer : D. 4 KHz

1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Description : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Last Answer : 22

The noise from an airplane engine 100 ft from an observer is found to have an intensity of 45dB. What will be the intensity when the plane flies overhead at an altitude of 1 mi? A. 10.5 dB B. 34.5 dB C. 35 dB D. 20.5 dB

Description : The noise from an airplane engine 100 ft from an observer is found to have an intensity of 45dB. What will be the intensity when the plane flies overhead at an altitude of 1 mi? A. 10.5 dB B. 34.5 dB C. 35 dB D. 20.5 dB

Last Answer : A. 10.5 dB

What is the difference between DBFile Sequential and Scattered Reads?(for DBA

Description : What is the difference between DBFile Sequential and Scattered Reads?(for DBA

Last Answer : Both "db file sequential read" and "db file scattered read" events signify time waited for I/O read requests to complete. Time is reported in 100's of a second for Oracle 8i releases and below, ... v_$system_event b where a.event = 'db file sequential read' and b.event = 'db file scattered read';

Which of the following is not a way of minimizing if not eliminating noise? A. Use redundancy B. Increase transmitted power C. Reduce signaling rate D. Increase channel bandwidth

Description : Which of the following is not a way of minimizing if not eliminating noise? A. Use redundancy B. Increase transmitted power C. Reduce signaling rate D. Increase channel bandwidth

Last Answer : D. Increase channel bandwidth

Noise always affects the signal in a communications systems at the ________. A. transmitter B. channel C. information source D. destination

Description : Noise always affects the signal in a communications systems at the ________. A. transmitter B. channel C. information source D. destination

Last Answer : B. channel

What theorem sets a limit on the maximum capacity of a channel with a given noise level? A. Nyquist theorem B. Hartley law C. Shannon-Hartley theorem D. Shannon theorem

Description : What theorem sets a limit on the maximum capacity of a channel with a given noise level? A. Nyquist theorem B. Hartley law C. Shannon-Hartley theorem D. Shannon theorem

Last Answer : C. Shannon-Hartley theorem

An interfering current in a telegraph or signaling channel due to telegraph or signaling current by another channel. A. Crosstalk B. Noise current C. Crossfire D. Intermodulation

Description : An interfering current in a telegraph or signaling channel due to telegraph or signaling current by another channel. A. Crosstalk B. Noise current C. Crossfire D. Intermodulation

Last Answer : C. Crossfire

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

______ sets the limit on the maximum capacity of a channel with a given noise level. A. Hartley theorem B. Shannon-hartley theorem C. Nyquist theorem D. Shannon theorem

Description : ______ sets the limit on the maximum capacity of a channel with a given noise level. A. Hartley theorem B. Shannon-hartley theorem C. Nyquist theorem D. Shannon theorem

Last Answer : B. Shannon-hartley theorem

Which does not effect noise in a channel? A. None of these B. Bandwidth C. Temperature D. Quantizing level

Description : Which does not effect noise in a channel? A. None of these B. Bandwidth C. Temperature D. Quantizing level

Last Answer : D. Quantizing level

________ sets a limit on the maximum capacity of a channel with a give noise level. A. Hartley theorem B. Shannon-Hartley theorem C. Nyquist theorem D. Shannon theorem

Description : ________ sets a limit on the maximum capacity of a channel with a give noise level. A. Hartley theorem B. Shannon-Hartley theorem C. Nyquist theorem D. Shannon theorem

Last Answer : B. Shannon-Hartley theorem

Standard design reference for environmental noise temperature. A. 300 K B. 290 K C. 32 ˚F D. 212˚F

Description : Standard design reference for environmental noise temperature. A. 300 K B. 290 K C. 32 ˚F D. 212˚F

Last Answer : B. 290 K

Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Description : Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Last Answer : A. 75

In ISDN, what is the basic access B channel data rate? A. 32 kbps B. 64 kbps C. 144 kbps D. 16 kbps

Description : In ISDN, what is the basic access B channel data rate? A. 32 kbps B. 64 kbps C. 144 kbps D. 16 kbps

Last Answer : B. 64 kbps

What is the data rate of the ISDN Basic access B channel? A. 192 kbps B. 32 kbps C. 64 kbps D. 144 kbps

Description : What is the data rate of the ISDN Basic access B channel? A. 192 kbps B. 32 kbps C. 64 kbps D. 144 kbps

Last Answer : C. 64 kbps

A student measures time for 20 oscillations of a simple pendulum as 30 s. 32 s, 35 s and 31 s. 1f the minimum division in the measuring clock

Description : A student measures time for 20 oscillations of a simple pendulum as 30 s. 32 s, 35 s and 31 s. 1f the minimum division in the measuring clock

Last Answer : A student measures time for 20 oscillations of a simple pendulum as 30 s. 32 s, 35 s and 31 s. 1f the minimum ... 1 (C) 32 2 (D) 32 5

The dimensions of a 35 litre forma for measuring aggregates by volume, are: (A) length 30 cm, breadth 25 cm, height 30 cm (B) length 39 cm, breadth 25 cm, height 32 cm (C) length 27 cm, breadth 27 cm, height 48 cm (D) length 220 cm, breadth 25 cm, height 40 cm

Description : The dimensions of a 35 litre forma for measuring aggregates by volume, are: (A) length 30 cm, breadth 25 cm, height 30 cm (B) length 39 cm, breadth 25 cm, height 32 cm (C) length 27 cm, breadth 27 cm, height 48 cm (D) length 220 cm, breadth 25 cm, height 40 cm

Last Answer : Answer: Option C

Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointer to mid-scale B. short the test leads and calibrate the meter reading to 'zero' C. change the meter's batteries D. center the meter's pointer at infinity

Description : Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointer to mid-scale B. short the test leads and calibrate the meter reading to 'zero' C. change the meter's batteries D. center the meter's pointer at infinity

Last Answer : Answer: B

Determine from the following the basic mode of transmission system in the public data network in which data are transferred from the source to the network and from the network to the destination in the frame format. A. Voice mode B. Asynchronous mode C. Synchronous mode D. Packet mode

Description : Determine from the following the basic mode of transmission system in the public data network in which data are transferred from the source to the network and from the network to the destination in the frame format. A. Voice mode B. Asynchronous mode C. Synchronous mode D. Packet mode

Last Answer : D. Packet mode

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : B. 2.656 watts

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : A. PAM

Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it is assumed that each sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Description : Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it ... sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Last Answer : (C) 128 kbps

28.38 N and 77.12 E are the respective latitude and longitude of which places? -Do You Know?

Description : 28.38 N and 77.12 E are the respective latitude and longitude of which places? -Do You Know?

Last Answer : answer:

28.38 N. and 77.12 E are the respective latitude and longitude of which one of the following places? [CDS 2008] (a) Jaipur (b) Delhi (c) Lucknow (d) Allahabad

Description : 28.38 N. and 77.12 E are the respective latitude and longitude of which one of the following places? [CDS 2008] (a) Jaipur (b) Delhi (c) Lucknow (d) Allahabad

Last Answer : Ans: (b)

The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Last Answer : Answer: D

28.38 N and 77.12 E are the respective latitude and longitude of which places?

Description : 28.38 N and 77.12 E are the respective latitude and longitude of which places?

Last Answer : Delhi