You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm
(pure test tone) convert the reading in dBmCO.
A. 16
B. 18
C. 22
D. 12
by

1 Answer

Answer :

C. 22
by

Related questions

In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Last Answer : B. 93

You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Description : You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Last Answer : C. 35

You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Last Answer : D. 32

You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Description : You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Last Answer : C. 38 dBa

Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Description : Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Last Answer : A. 75

Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Description : Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Last Answer : D. B and C above

The standard test tone A. 0dB B. 10 dBm C. 0 dBm D. 10 dB

Description : The standard test tone A. 0dB B. 10 dBm C. 0 dBm D. 10 dB

Last Answer : C. 0 dBm

At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm

Description : At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm

Last Answer : D. -90 dBm

ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB

Description : ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB

Last Answer : B. -90 dBm

You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Description : You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Last Answer : C. 25

A reading of -50 dBm on the disturbing pair, and -80 on the disturbed pair equals _____ dB of crosstalk coupling. A. 20 B. 30 C. 60 D. 25

Description : A reading of -50 dBm on the disturbing pair, and -80 on the disturbed pair equals _____ dB of crosstalk coupling. A. 20 B. 30 C. 60 D. 25

Last Answer : B. 30

Which stands for dB relative level? A. dBrn B. dBm C. dBr D. dBa

Description : Which stands for dB relative level? A. dBrn B. dBm C. dBr D. dBa

Last Answer : C. dBr

What is the reference tone level for dBa? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Description : What is the reference tone level for dBa? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Last Answer : D. -85 dBm

What is the reference tone level for dBrn? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Description : What is the reference tone level for dBrn? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Last Answer : A. -90 dBm

ECE Board Exam March 1996 What is the reference tone level for dBm? A. -82 dBm B. -85 dBm C. -67 dBm D. -90 dBm

Description : ECE Board Exam March 1996 What is the reference tone level for dBm? A. -82 dBm B. -85 dBm C. -67 dBm D. -90 dBm

Last Answer : D. -90 dBm

Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Description : Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Last Answer : C. dBmc

ECE Board Exam March 1996 Crosstalk coupling is ___________. A. dBm (disturbing pair) minus dBm (disturbed pair) B. the difference between readings on a cable pair with a tone and a cable pair without tone read at the far end of a cable C. signals from one circuit that get into another circuit D. All of these are true

Description : ECE Board Exam March 1996 Crosstalk coupling is ___________. A. dBm (disturbing pair) minus dBm (disturbed pair) B. the difference between readings on a cable pair with a tone and a cable pair without ... a cable C. signals from one circuit that get into another circuit D. All of these are true

Last Answer : D. All of these are true

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

ECE Board Exam March 1996 The power of standard test tone is normally ____________. A. 1 dB B. 0 mW C. 1 mW D. 1 W

Description : ECE Board Exam March 1996 The power of standard test tone is normally ____________. A. 1 dB B. 0 mW C. 1 mW D. 1 W

Last Answer : C. 1 mW

When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?

Description : When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?

Last Answer : Attenuations of the directional coupler and the connecting cable.

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : B. 2.656 watts

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : A. PAM

A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Last Answer : D. 8.8 dB

A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Description : A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Last Answer : C. 999.8 kHz, 1000 kHz, and 1000.2 kHz

The difference between signal strength at a given point and a reference level is________. A. power B. dBm C. level D. ratio

Description : The difference between signal strength at a given point and a reference level is________. A. power B. dBm C. level D. ratio

Last Answer : C. level

Nominal voice channel A. 20 to 20 KHz B. 16 to 16 KHz C. 3 to 3 KHz D. 4 KHz

Description : Nominal voice channel A. 20 to 20 KHz B. 16 to 16 KHz C. 3 to 3 KHz D. 4 KHz

Last Answer : D. 4 KHz

The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant, what does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

The agreed standard for measuring loudness is the loudness sensation produced by a 1000 Hz sine wave _____ dB above the listener’s threshold of hearing. A. 80 B. 50 C. 30 D. 40

Description : The agreed standard for measuring loudness is the loudness sensation produced by a 1000 Hz sine wave _____ dB above the listener’s threshold of hearing. A. 80 B. 50 C. 30 D. 40

Last Answer : D. 40

What is the reference level for noise measurement, F1A weighted? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Description : What is the reference level for noise measurement, F1A weighted? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Last Answer : D. -85 dBm

What is the reference noise level? A. 10 pW B. 0 dBm C. 1mW D. -90 dBm

Description : What is the reference noise level? A. 10 pW B. 0 dBm C. 1mW D. -90 dBm

Last Answer : D. -90 dBm

What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Last Answer : C. 125,000

ECE Board Exam March 1996 A car horn outdoors produces a sound intensity level of 90 dB at 10 ft away. At this distance, what is the sound power in watt? A. 12 W B. 0.12 W C. 0.012 W D. 1.2 W

Description : ECE Board Exam March 1996 A car horn outdoors produces a sound intensity level of 90 dB at 10 ft away. At this distance, what is the sound power in watt? A. 12 W B. 0.12 W C. 0.012 W D. 1.2 W

Last Answer : C. 0.012 W

The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Description : The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Last Answer : D. 14 dB

Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointer to mid-scale B. short the test leads and calibrate the meter reading to 'zero' C. change the meter's batteries D. center the meter's pointer at infinity

Description : Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointer to mid-scale B. short the test leads and calibrate the meter reading to 'zero' C. change the meter's batteries D. center the meter's pointer at infinity

Last Answer : Answer: B

What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Last Answer : D. 150 W

While measuring frequency response, as the signal generator approaches the lowest and highest frequency the recorder can effectively record, the VTVM reading drops to less than - 3 dB. What does this indicate?

Description : While measuring frequency response, as the signal generator approaches the lowest and highest frequency the recorder can effectively record, the VTVM reading drops to less than - 3 dB. What does this indicate?

Last Answer : The upper and lower limits of the frequency response specification for that tape recorder.

In reference to dB meters, 0 dBm represents 1 milliwatt into what value of load?

Description : In reference to dB meters, 0 dBm represents 1 milliwatt into what value of load?

Last Answer : 600-ohm load.

For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Description : For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Last Answer : ∙ C. -35 dBm

What is the gain, in dB of a helical antenna with diameter of λ/3, 10 turns at pitch of λ/4, used at 100 MHz? A. 16 B. 41.1 C. 31.4 D. 1.25

Description : What is the gain, in dB of a helical antenna with diameter of λ/3, 10 turns at pitch of λ/4, used at 100 MHz? A. 16 B. 41.1 C. 31.4 D. 1.25

Last Answer : A. 16

What device measures rf power by measuring the heat the rf power generates? A. Calorimeter B. Goniometer C. Spectrum meter D. Oscilloscope

Description : What device measures rf power by measuring the heat the rf power generates? A. Calorimeter B. Goniometer C. Spectrum meter D. Oscilloscope

Last Answer : A. Calorimeter

A measurement of -75 dBm, C-message weighted, would be _________ dBrnc. A. 8 B. 7 C. 9 D. 15

Description : A measurement of -75 dBm, C-message weighted, would be _________ dBrnc. A. 8 B. 7 C. 9 D. 15

Last Answer : D. 15

15 dBa F1A weighted, equals ___________. A. -90 dBm B. -82 dBm C. -85 dBm D. -70 dBm

Description : 15 dBa F1A weighted, equals ___________. A. -90 dBm B. -82 dBm C. -85 dBm D. -70 dBm

Last Answer : D. -70 dBm

F1A weighting refers to ___________. A. -90 dBm B. dBrnc0 C. dBrnc D. F1A handset

Description : F1A weighting refers to ___________. A. -90 dBm B. dBrnc0 C. dBrnc D. F1A handset

Last Answer : C. dBrnc

What is the unit of noise power of psophometer? A. pWp B. dBa C. dBm D. dBrn

Description : What is the unit of noise power of psophometer? A. pWp B. dBa C. dBm D. dBrn

Last Answer : A. pWp

What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36

Description : What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36

Last Answer : A. 1.09

The most common unit of noise measurement in white noise voltage testing. A. NPR B. dBm C. dBW D. dBrn

Description : The most common unit of noise measurement in white noise voltage testing. A. NPR B. dBm C. dBW D. dBrn

Last Answer : A. NPR

Unit of noise power of psophometer A. dBa B. pWp C. dBm D. dBmO

Description : Unit of noise power of psophometer A. dBa B. pWp C. dBm D. dBmO

Last Answer : B. pWp

The most common unit of noise measurement in white noise testing. A. dBw B. dBk C. dBm D. NPR

Description : The most common unit of noise measurement in white noise testing. A. dBw B. dBk C. dBm D. NPR

Last Answer : D. NPR

Noise reduction system used for film sound in movie A. dBx B. dolby C. dBa D. dBm

Description : Noise reduction system used for film sound in movie A. dBx B. dolby C. dBa D. dBm

Last Answer : B. dolby

What is the equivalent output of a circuit in dBm, if it is has an output of 10 watts? A. 10 dBm B. 30 dBm C. 20 dBm D. 40 dBm

Description : What is the equivalent output of a circuit in dBm, if it is has an output of 10 watts? A. 10 dBm B. 30 dBm C. 20 dBm D. 40 dBm

Last Answer : D. 40 dBm