Suggest the degree of workability in terms of slump for the following: i) Pavements using pavers ii) Canal lining iii) Heavily reinforced sections iv) In-situ piling

Suggest the degree of workability in terms of slump for the following: i) Pavements using pavers ii) Canal lining iii) Heavily reinforced sections iv) In-situ piling
by

1 Answer

Answer :

Degree of workability in terms of slump for the following:

i) Pavements using pavers: 25-75 mm

ii) Canal lining: 70-80 mm

iii) Heavily reinforced sections: 50-100 mm

iv) In-situ piling: 100-150 mm
by

Related questions

For concreting of heavily reinforced sections without vibration, the workability of concrete expressed as compacting factor should be (A) 0.75 - 0.80 (B) 0.80 - 0.85 (C) 0.85 - 0.92 (D) Above 0.92

Description : For concreting of heavily reinforced sections without vibration, the workability of concrete expressed as compacting factor should be (A) 0.75 - 0.80 (B) 0.80 - 0.85 (C) 0.85 - 0.92 (D) Above 0.92

Last Answer : Answer: Option D

Higher workability of concrete is required if the structure is (A) Made with cement concrete (B) Thick and reinforced (C) Thin and heavily reinforced (D) Thick and heavily reinforced

Description : Higher workability of concrete is required if the structure is (A) Made with cement concrete (B) Thick and reinforced (C) Thin and heavily reinforced (D) Thick and heavily reinforced

Last Answer : Answer: Option D

Workability of a concrete – mix is determined by (i)Slump cone test (ii)Compaction factor test (iii)Vee bee test [ A ] i [ B ] ii [ C ] i and ii [ D ] i, ii and iii

Description : Workability of a concrete – mix is determined by (i)Slump cone test (ii)Compaction factor test (iii)Vee bee test [ A ] i [ B ] ii [ C ] i and ii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

For high degree of workability, the slump value should vary between (a) 0 to 25mm (b) 25 to 50mm (c) 50 to 80mm (d) 80 to 100mm

Description : For high degree of workability, the slump value should vary between (a) 0 to 25mm (b) 25 to 50mm (c) 50 to 80mm (d) 80 to 100mm

Last Answer : (d) 80 to 100mm

Explain the procedure for measurement of workability of fresh concrete using slump cone test.

Description : Explain the procedure for measurement of workability of fresh concrete using slump cone test.

Last Answer : Test Procedure: i. Clean the mould from inside and apply oil to it. ii. Place the mould on smooth horizontal, rigid & non-absorbent surface or the centre of metallic tray. iii. Fill the mould ... top of cone. vi. Based on measured slump, the degree of workability is designated as follows.

If the slump of a concrete mix is 60 mm, its workability is (A) Very low (B) Low (C) Medium (D) High

Description : If the slump of a concrete mix is 60 mm, its workability is (A) Very low (B) Low (C) Medium (D) High

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) Higher workability indicates unexpected increase in the moisture content (B) Higher workability indicates deficiency of sand (C) If the concrete mix is dry, the slump is zero (D) All the above

Description : Pick up the correct statement from the following: (A) Higher workability indicates unexpected increase in the moisture content (B) Higher workability indicates deficiency of sand (C) If the concrete mix is dry, the slump is zero (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) An increase in water content must be accompanied by an increase in cement content (B) Angular and rough aggregates reduce the workability of the concrete (C) The slump of the concrete mix decreases due to an increase in temperature (D) All the above

Description : Pick up the correct statement from the following: (A) An increase in water content must be accompanied by an increase in cement content (B) Angular and rough aggregates reduce the workability of the ... The slump of the concrete mix decreases due to an increase in temperature (D) All the above

Last Answer : Answer: Option D

Workability of concrete is measured by (A) Vicat apparatus test (B) Slump test (C) Minimum void method (D) Talbot Richa

Description : Workability of concrete is measured by (A) Vicat apparatus test (B) Slump test (C) Minimum void method (D) Talbot Richa

Last Answer : Answer: Option B

Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) Segregation is necessary for a workable concrete (B) Consistency does not affect the workability of concrete (C) If the concrete mix is dry, the slump is maximum (D) None of these

Description : Pick up the correct statement from the following: (A) Segregation is necessary for a workable concrete (B) Consistency does not affect the workability of concrete (C) If the concrete mix is dry, the slump is maximum (D) None of these

Last Answer : Answer: Option D

Slump test for concrete is carried out, to determine (A) Strength (B) Durability (C) Workability (D) Water content

Description : Slump test for concrete is carried out, to determine (A) Strength (B) Durability (C) Workability (D) Water content

Last Answer : Answer: Option C

The workability of concrete is expressed by (a) Water-cement ratio (b) Slump value (c) Compaction factor (d) Both (a) and (b)

Description : The workability of concrete is expressed by (a) Water-cement ratio (b) Slump value (c) Compaction factor (d) Both (a) and (b)

Last Answer : (d) Both (a) and (b)

If the slump of a concrete mix is 50 to 100 mm, its workability is [ A ] Very low [ B ] Low [ C ] Medium [ D ] High

Description : If the slump of a concrete mix is 50 to 100 mm, its workability is [ A ] Very low [ B ] Low [ C ] Medium [ D ] High

Last Answer : [ C ] Medium

Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Last Answer : [ C ] Compaction factor test

While determining the workability of concrete mix, the compaction factor test is ------than the slump cone test [ A ] Less accurate [ B ] More accurate [ C ] Approximate method [ D ] None of the above

Description : While determining the workability of concrete mix, the compaction factor test is ------than the slump cone test [ A ] Less accurate [ B ] More accurate [ C ] Approximate method [ D ] None of the above

Last Answer : [ B ] More accurate

Slump cone test is used to determine [ A ] Shrinkage of concrete mix [ B ] Creep of concrete [ C ] Workability of concrete mix [ D ] Soundness of concrete

Description : Slump cone test is used to determine [ A ] Shrinkage of concrete mix [ B ] Creep of concrete [ C ] Workability of concrete mix [ D ] Soundness of concrete

Last Answer : [ C ] Workability of concrete mix

Expanded metal is (A) Manufactured from steel sheets (B) Used for reinforced concrete in road pavements (C) Measured in term of SWM (short way mesh) and LWM (long way mesh) (D) All the above

Description : Expanded metal is (A) Manufactured from steel sheets (B) Used for reinforced concrete in road pavements (C) Measured in term of SWM (short way mesh) and LWM (long way mesh) (D) All the above

Last Answer : Answer: Option D

After how much time lining of crucible should be changed ? (i) After every weld (ii) After 7 welds (iii) After every 10 welds* (iv) None of the above

Description : After how much time lining of crucible should be changed ? (i) After every weld (ii) After 7 welds (iii) After every 10 welds* (iv) None of the above

Last Answer : (iii) After every 10 welds*

Thickness of Lining/Charge is kept? (i) 20 mm. (ii) 25 mm* (iii) 30 mm (iv) As decided by the site supervisor

Description : Thickness of Lining/Charge is kept? (i) 20 mm. (ii) 25 mm* (iii) 30 mm (iv) As decided by the site supervisor

Last Answer : (ii) 25 mm*

Suggest the compaction factor for the following degree of workability.

Description : Suggest the compaction factor for the following degree of workability.

Last Answer : Suggest the compaction factor for the following degree of workability.

Define the following special types of concretes with its one use. i) Vacuum concrete ii) Fiber reinforced concrete iii) High performance concrete iv) Self-compacting concrete

Description : Define the following special types of concretes with its one use. i) Vacuum concrete ii) Fiber reinforced concrete iii) High performance concrete iv) Self-compacting concrete

Last Answer : The uses of special types of concretes are as follows.  i) Vacuum concrete: It is the concrete in which entrained air and excess water form concrete mix is taken out from vacuum pump, ... . large bridge and machine foundations iii. Pumped concrete for floors and slabs. iv. Pre-stressed concrete

Which of the following statement(s) is/are correct with reference to curve generation? I. Hermite curves are generated using the concepts of interpolation. II. Bezier curves are generated using the concepts of approximation. III. The Bezier curves lies entirely within the convex hull of its control points. IV. The degree of Bezier curve does not depend on the number of control points. (A) I, II and IV only (B) II and III only (C) I and II only (D) I, II and III only

Description : Which of the following statement(s) is/are correct with reference to curve generation? I. Hermite curves are generated using the concepts of interpolation. II. Bezier curves are generated using the concepts of approximation. III. The ... (B) II and III only (C) I and II only (D) I, II and III only

Last Answer : (D) I, II and III only

Suggest a suitable subject for this letter. (i) Thefts are on the increase. (ii) Increasing threat of theft in Shyam Nagar. (iii) necessity of appointing day and night guards by the RWA. (iv) to call a meeting of the area residents.

Description : Suggest a suitable subject for this letter. (i) Thefts are on the increase. (ii) Increasing threat of theft in Shyam Nagar. (iii) necessity of appointing day and night guards by the RWA. (iv) to call a meeting of the area residents.

Last Answer : Increasing threat of theft in Shyam Nagar Gurgaon

Suggest the type of glass used for the following work: i) Making panel of partition wall ii) Cashier Cabin iii) Skylight iv) Door Shutter

Description : Suggest the type of glass used for the following work: i) Making panel of partition wall ii) Cashier Cabin iii) Skylight iv) Door Shutter

Last Answer : i) Making panel of partition wall: Block glass OR Sheet Glass OR chipped and ground glass OR soda lime glass ii) Cashier Cabin-Polished plate glass OR bullet proof glass OR soda lime glass OR laminated ... clear window glass or lead glass iv) Door Shutter: Soda lime glass OR tempered glass

Suggest the type of cement used for the following : (i) For modular construction where form work needs to be removed early for re-use. . (ii) Mass concreting such as construction of dam. (iii) Decorative works in external surfaces of building. (iv) Cementing the oil well.

Description : Suggest the type of cement used for the following : (i) For modular construction where form work needs to be removed early for re-use. . (ii) Mass concreting such as construction of dam. (iii) Decorative works in external surfaces of building. (iv) Cementing the oil well.

Last Answer : i) For modular construction where form work needs to be removed early for reuse. – Rapid Hardening Cement ii) Mass concreting such as construction of dam. – Low heat cement. iii) Decorative works in external surfaces of building – Coloured cement. iv) Cementing the oil well. – Oil Well Cement. 

Suggest the type of lubricant used for the following jobs: i) Clock ii) I.C. Engines iii) Gears iv) Sewing machine

Description : Suggest the type of lubricant used for the following jobs: i) Clock ii) I.C. Engines iii) Gears iv) Sewing machine

Last Answer : i) Clock : Vegetable and animal oils like palm oil, hazel nut oil, neat foot oil, etc ii) I.C. Engines: Mineral oils containing additives are used. iii) Gears: Thick mineral oils containing ... Mineral oil, silicones, thin vegetable and animal oils like palm oil, hazel nut oil, neat foot oil.

Suggest one type of materials for water proofing for the following situations. i. Rising dampness in building ii. Leakages in dam iii. Concrete continuously in wet or damp condition iv. Leakages in lavatory ,bathroom and kitchen floor v. Cracks on plastered surface vi. Cracks on roof surface

Description : Suggest one type of materials for water proofing for the following situations. i. Rising dampness in building ii. Leakages in dam iii. Concrete continuously in wet or damp condition iv. Leakages in lavatory ,bathroom and kitchen floor v. Cracks on plastered surface vi. Cracks on roof surface

Last Answer : i. Flexible materials like butyl rubber, hot bitumen (asphalt), plastic sheets, bituminous felts, sheets of lead. ii. Liquid applied cementitious membranes iii. Liquid applied cementitious membranes ... v. Liquid applied cementitious membranes. vi. Brick bat coba, liquid applied bituminous membrane.

Suggest the minimum grade of concrete for following exposure condition. i) RCC work ii) Water retaining structure iii) Sea water construction iv) Pre-stressed concrete

Description : Suggest the minimum grade of concrete for following exposure condition. i) RCC work ii) Water retaining structure iii) Sea water construction iv) Pre-stressed concrete

Last Answer : Minimum grade of concrete for following exposure condition: i) RCC work = M 20 ii) Water retaining structure = M 25 iii) Sea water construction = M 20 for PCC and M 30 for RCC iv) Pre-stressed concrete = M 30

Suggest electric motors for i) traction ii) crane iii) lathe machine iv) domestic fan.

Description : Suggest electric motors for i) traction ii) crane iii) lathe machine iv) domestic fan.

Last Answer : i) Traction :- DC Series motor  ii) Crane :- DC Series motor  iii) Lathe machine :- 3 phase Induction motor or DC shunt motor  iv) Domestic fan :- 1 phase induction motor

Suggest the energy conservation techniques in following cases : (i) Motor is running with 70% loaded condition. (ii) Motor is continuously loaded at 50%. (iii) Motor runs with 30% loaded condition but sometimes rises to 50% loading condition. (iv) Motor runs continuously under no-load condition.

Description : Suggest the energy conservation techniques in following cases : (i) Motor is running with 70% loaded condition. (ii) Motor is continuously loaded at 50%. (iii) Motor runs with 30% loaded condition but sometimes rises to 50% loading condition. (iv) Motor runs continuously under no-load condition.

Last Answer : Following are the suggestion the energy conservation techniques in following cases :  (i) Motor is running with 70% loaded condition: Use APFC or IPFC for better power factor improvement. Use ... If possible use low capacity motor for above condition. If possible switch off the motor.

In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line of the beam before bending remain plane after bending (D) Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Last Answer : Answer: Option C

In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Description : In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Last Answer : Answer: Option D

A doubly reinforced section is used (a) When the members are subjected to alternate external loads and the bending moment in the sections reverses. (b) When the member are subjected to loading eccentric in either side of the axis. (c) When the members are subjected to accidental lateral loads . (d) All of the above

Description : A doubly reinforced section is used (a) When the members are subjected to alternate external loads and the bending moment in the sections reverses. (b) When the member are subjected to loading eccentric in ... . (c) When the members are subjected to accidental lateral loads . (d) All of the above

Last Answer : (d) All of the above

Steel Beam theory is the method of analysis and a design of [ A ] Singly reinforced sections [ B ] Doubly reinforced sections [ C ] Both (a) and (b) [ D ] Steel structures only

Description : Steel Beam theory is the method of analysis and a design of [ A ] Singly reinforced sections [ B ] Doubly reinforced sections [ C ] Both (a) and (b) [ D ] Steel structures only

Last Answer : [ B ] Doubly reinforced sections

Strain compatibility method is the method used for the analysis and design of [ A ] singly reinforced sections [ B ] doubly reinforced sections [ C ] both (a) and (b) [ D ] neither (a) nor (b)

Description : Strain compatibility method is the method used for the analysis and design of [ A ] singly reinforced sections [ B ] doubly reinforced sections [ C ] both (a) and (b) [ D ] neither (a) nor (b)

Last Answer : [ C ] both (a) and (b)

Which of the following sections are preferable for designing a member [ A ] under reinforced sections [ B ] over reinforced sections [ C ] both (a) and (b) [ D ] balanced sections

Description : Which of the following sections are preferable for designing a member [ A ] under reinforced sections [ B ] over reinforced sections [ C ] both (a) and (b) [ D ] balanced sections

Last Answer : [ A ] under reinforced sections

Steel Beam theory is the method of analysis and a design of [ A ] Singly reinforced sections [ B ] Doubly reinforced sections [ C ] Both (a) and (b) [ D ] Steel structures only

Description : Steel Beam theory is the method of analysis and a design of [ A ] Singly reinforced sections [ B ] Doubly reinforced sections [ C ] Both (a) and (b) [ D ] Steel structures only

Last Answer : [ B ] Doubly reinforced sections

Strain compatibility method is the method used for the analysis and design of [ A ] singly reinforced sections [ B ] doubly reinforced sections [ C ] both (a) and (b) [ D ] neither (a) nor (b)

Description : Strain compatibility method is the method used for the analysis and design of [ A ] singly reinforced sections [ B ] doubly reinforced sections [ C ] both (a) and (b) [ D ] neither (a) nor (b)

Last Answer : [ C ] both (a) and (b)

Which of the following sections are preferable for designing a member [ A ] under reinforced sections [ B ] over reinforced sections [ C ] both (a) and (b) [ D ] balanced sections

Description : Which of the following sections are preferable for designing a member [ A ] under reinforced sections [ B ] over reinforced sections [ C ] both (a) and (b) [ D ] balanced sections

Last Answer : [ A ] under reinforced sections

Steel Beam theory is a method of designing [ A ] Balanced sections [ B ] Critical sections [ C ] Singly reinforced beams [ D ] Doubly reinforced beams

Description : Steel Beam theory is a method of designing [ A ] Balanced sections [ B ] Critical sections [ C ] Singly reinforced beams [ D ] Doubly reinforced beams

Last Answer : [ D ] Doubly reinforced beams

Padma The bridge Piling Depth How much ?

Description : Padma The bridge Piling Depth How much ?

Last Answer : approx 363 Feet Deep

Padma The bridge Total Piling Numbers How much ?

Description : Padma The bridge Total Piling Numbers How much ?

Last Answer : Padma On the bridge Total 264 T. Piling There are.

The arrangement of supporting an existing structure by providing supports underneath, is known as (A) Shoring (B) Underpinning (C) Jacking (D) Piling

Description : The arrangement of supporting an existing structure by providing supports underneath, is known as (A) Shoring (B) Underpinning (C) Jacking (D) Piling

Last Answer : Answer: Option B

Lining of brain ventricle & central canal of spinal cord is called as :-

Description : Lining of brain ventricle & central canal of spinal cord is called as :-

Last Answer : Lining of brain ventricle & central canal of spinal cord is called as :- A. Ependyma B. Endothelium C. Mesothelium D. Neurosensory

Lining of brain ventricle & central canal of spinal cord is lined by :-

Description : Lining of brain ventricle & central canal of spinal cord is lined by :-

Last Answer : Lining of brain ventricle & central canal of spinal cord is lined by :- A. Ependyma epithelium B. Endothelium C. Mesothelium D. Neurosensory

A longitudinal tear or ulceration in the lining of the anal canal is termed a (an) a) anal fissure. Fissures are usually caused by the trauma of passing a large, firm stool or from persistent tightening of the anal canal secondary to stress or anxiety (leading to constipation). b) anorectal abscess. An anorectal abscess is an infection in the pararectal spaces. c) anal fistula. An anal fistula is a tiny, tubular, fibrous tract that extends into the anal canal from an opening located beside the anus. d) hemorrhoid. A hemorrhoid is a dilated portion of vein in the anal canal.

Description : A longitudinal tear or ulceration in the lining of the anal canal is termed a (an) a) anal fissure. Fissures are usually caused by the trauma of passing a large, firm stool or from persistent ... beside the anus. d) hemorrhoid. A hemorrhoid is a dilated portion of vein in the anal canal.

Last Answer : a) anal fissure. Fissures are usually caused by the trauma of passing a large, firm stool or from persistent tightening of the anal canal secondary to stress or anxiety (leading to constipation).

Which of the following statements is correct? (a) Sulphate resisting cement is particularly used for canal lining. (b) Low heat cement should not be used for thin concrete structures. (c) Rapid hardening cement should not be used for massive concrete structures (d) All of the above

Description : Which of the following statements is correct? (a) Sulphate resisting cement is particularly used for canal lining. (b) Low heat cement should not be used for thin concrete structures. (c) Rapid hardening cement should not be used for massive concrete structures (d) All of the above

Last Answer : (d) All of the above

Describe any two design considerations for Precast Canal lining.

Description : Describe any two design considerations for Precast Canal lining.

Last Answer : 1. Precast concrete slabs, laid properly on carefully prepared sub-grades and with the joints, effectively sealed, constitute a serviceable type of lining. The precast slabs are about 5 to ... . However, seepage losses are obviously more. Transportation of precast slabs may contribute to breakage. 

Match the items given in column I with those in column II and select the correct option given below. Column I Column II A. Proliferative phase (i) Breakdown of endometrial lining B. Secretory phase (ii) Follicular phase C. Menstruation (iii) Luteal phase A B C (a) (iii) (ii) (i) (b) (i) (iii) (ii) (c) (ii) (iii) (i) (d) (iii) (i) (ii)

Description : Match the items given in column I with those in column II and select the correct option given below. Column I Column II A. Proliferative phase (i) Breakdown of endometrial lining B. Secretory phase (ii) Follicular phase C. Menstruation ( ... ) (i) (iii) (ii) (c) (ii) (iii) (i) (d) (iii) (i) (ii)

Last Answer : (c) (ii) (iii) (i)