Description : Label size of foreign article is min & postage paid words should not be less than a) 70mm X 100mm & 300sq mm b) 50mm X 80mm & 200sq mm c) 25mm X 50 mm & 100 sq mm d) None of these
Last Answer : a) 70mm X 100mm & 300sq mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : If the slump of a concrete mix is 50 to 100 mm, its workability is [ A ] Very low [ B ] Low [ C ] Medium [ D ] High
Last Answer : [ C ] Medium
Description : .The undercut for Cobalt Chrome’s retentive arm clasp is, A. 0.75mm B. 0.50mm C. 0.25mm
Last Answer : C. 0.25mm
Description : The gap between scaffold planks (boards) must be no more than? a. 150mm (6 inches) b. 50mm (2 inches) c. 75mm (3 inches) d. 25mm (1 inch)
Last Answer : d. 25mm (1 inch)
Description : The top diameter, bottom diameter and height of the mould used for slump test are (a) 100mm, 200mm, 300mm (b) 200mm,100mm,300mm (c) 200mm,300mm,100mm (d) 100mm,300mm,200mm
Last Answer : (a) 100mm, 200mm, 300mm
Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm
Last Answer : b) 140mm
Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm
Last Answer : a) 100mm
Description : The workability of concrete is expressed by (a) Water-cement ratio (b) Slump value (c) Compaction factor (d) Both (a) and (b)
Last Answer : (d) Both (a) and (b)
Description : Suggest the degree of workability in terms of slump for the following: i) Pavements using pavers ii) Canal lining iii) Heavily reinforced sections iv) In-situ piling
Last Answer : Degree of workability in terms of slump for the following: i) Pavements using pavers: 25-75 mm ii) Canal lining: 70-80 mm iii) Heavily reinforced sections: 50-100 mm iv) In-situ piling: 100-150 mm
Description : If the slump of a concrete mix is 60 mm, its workability is (A) Very low (B) Low (C) Medium (D) High
Last Answer : Answer: Option C
Description : Pick up the correct statement from the following: (A) Higher workability indicates unexpected increase in the moisture content (B) Higher workability indicates deficiency of sand (C) If the concrete mix is dry, the slump is zero (D) All the above
Last Answer : Answer: Option D
Description : Pick up the correct statement from the following: (A) An increase in water content must be accompanied by an increase in cement content (B) Angular and rough aggregates reduce the workability of the ... The slump of the concrete mix decreases due to an increase in temperature (D) All the above
Description : Workability of concrete is measured by (A) Vicat apparatus test (B) Slump test (C) Minimum void method (D) Talbot Richa
Last Answer : Answer: Option B
Description : Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test
Description : Pick up the correct statement from the following: (A) Segregation is necessary for a workable concrete (B) Consistency does not affect the workability of concrete (C) If the concrete mix is dry, the slump is maximum (D) None of these
Description : Slump test for concrete is carried out, to determine (A) Strength (B) Durability (C) Workability (D) Water content
Description : Workability of a concrete – mix is determined by (i)Slump cone test (ii)Compaction factor test (iii)Vee bee test [ A ] i [ B ] ii [ C ] i and ii [ D ] i, ii and iii
Last Answer : [ D ] i, ii and iii
Description : Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test
Last Answer : [ C ] Compaction factor test
Description : While determining the workability of concrete mix, the compaction factor test is ------than the slump cone test [ A ] Less accurate [ B ] More accurate [ C ] Approximate method [ D ] None of the above
Last Answer : [ B ] More accurate
Description : Slump cone test is used to determine [ A ] Shrinkage of concrete mix [ B ] Creep of concrete [ C ] Workability of concrete mix [ D ] Soundness of concrete
Last Answer : [ C ] Workability of concrete mix
Description : Explain the procedure for measurement of workability of fresh concrete using slump cone test.
Last Answer : Test Procedure: i. Clean the mould from inside and apply oil to it. ii. Place the mould on smooth horizontal, rigid & non-absorbent surface or the centre of metallic tray. iii. Fill the mould ... top of cone. vi. Based on measured slump, the degree of workability is designated as follows.
Description : In slump test, each layer of concrete is compacted by a steel rod 60 cm long and of 16 mm diameter for (A) 20 times (B) 25 times (C) 30 times (D) 50 time
Description : The slump recommended for mass concrete is about (A) 25 mm to 50 mm (B) 50 mm to 100 mm (C) 100 mm to 125 mm (D) 125 mm to 150 mm
Last Answer : Answer: Option A
Description : The concrete slump recommended for beams and slabs; is (A) 25 to 50 mm (B) 25 to 75 mm (C) 30 to 125 mm (D) 50 to 100 mm
Description : The concrete slump recommended for columns, is (A) 25 to 50 mm (B) 25 to 75 mm (C) 75 to 125 mm (D) 50 to 100 mm
Description : The concrete slump recommended for foundations, is (A) 25 to 50 mm (B) 30 to 125 mm (C) 50 to 100 mm (D) 75 to 125 mm
Description : For high degree of workability , the compaction factor is (a) 0.65 (b) 0.75 (c) 0.85 (d) 0.95
Last Answer : (d) 0.95
Description : For concreting of heavily reinforced sections without vibration, the workability of concrete expressed as compacting factor should be (A) 0.75 - 0.80 (B) 0.80 - 0.85 (C) 0.85 - 0.92 (D) Above 0.92
Description : For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above
Description : Ultra low volume sprayer consist of high spinning disc which makes droplet size a. 50 -100mm. b 40-100mm. c.35-100mm. d. None of above
Last Answer : Ans- c. 35-100mm.
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : Degree of saturation of a natural soil deposit having water content 15%, specific gravity 2.50 and void ratio 0.5, is (A) 50 % (B) 60 % (C) 75 % (D) 80 %
Last Answer : (C) 75 %
Description : For performing the compressive strength test of cement, the size of cube mould should be (a) 7.06cm (b)75mm (c)80mm (d)All the above
Last Answer : (a) 7.06cm
Description : If the viscosity of ground water is 1.00, the Slitcher's constant is 400, the effective size of soil particles in aquifer is 0.5 mm and hydraulic gradient is 1 in 80, the velocity of flow is (A) 0.25 m/day (B) 0.50 m/day (C) 1.00 m/day (D) 1.25 m/day
Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value
Last Answer : (A) Consistency
Description : Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value
Last Answer : [ A ] Consistency
Description : On inspecting a completed weld which has charpy impact requirements some small, smooth, shallow areas of undercut have been found
Last Answer : d) Only allow the welder to cosmetically blend out the undercut
Description : Material used for construction of transformer core is usually A. 0.4mm to 0.5 mm B. 4mm to 5 mm C. 14mm to 15 mm D. 25mm to 40 mm
Last Answer : d) 25mm to 40mm
Description : Wp and Wf are the weights of a cylinder containing partially compacted and fully compacted concrete. If the compaction factor (Wp/Wf ) is 0.95, the workability of concrete is (A) Extremely low (B) Very low (C) Low (D) High
Last Answer : Option D
Description : For dam construction the size of aggregates are (a) 40mm (b) 50mm (c) 60mm (d) 75mm
Last Answer : (a) 40mm
Description : The length of the vicat plunger is (a) 40mm (b) 60mm (c) 50mm (d) 30mm
Last Answer : (c) 50mm
Description : While compacting the concrete by a mechanical vibrator, the slump should not exceed (A) 2.5 cm (B) 5.0 cm (C) 7.5 cm (D) 10 cm
Description : For a given material Young's modulus is 200 GN/m2 and modulus of rigidity is 80 GN/m2 . The value of Poisson's ratio is (A) 0.15 (B) 0.20 (C) 0.25 (D) 0.30
Last Answer : (C) 0.25
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed
Last Answer : c) 41666.7N
Description : Suggest the compaction factor for the following degree of workability.
Last Answer : Suggest the compaction factor for the following degree of workability.