_______ is more prevalent in analog signals that have steep slopes or whose amplitudes vary rapidly. A. Peak limiting B. Quantization noise C. Granular noise D. Slope overload

_______ is more prevalent in analog signals that have steep slopes or whose amplitudes vary
rapidly.
A. Peak limiting
B. Quantization noise
C. Granular noise
D. Slope overload
by

1 Answer

Answer :

D. Slope overload
by

Related questions

Which of the following term best described the overload distortion? A. Peak limiting B. Quantization noise C. Granular noise D. Slope distortion

Description : Which of the following term best described the overload distortion? A. Peak limiting B. Quantization noise C. Granular noise D. Slope distortion

Last Answer : A. Peak limiting

Define slope overload noise and granular noise.

Description : Define slope overload noise and granular noise.

Last Answer : Slope overload noise is introduced due to the use of a step size delta is too small To follow some portions of the waveform with a step size.   Granular noise results from using a step size that is too large in parts of the waveform having a small slope. 

The bounded Quantization error is also called__________. A. overload error B. overload noise C. granular error D. All of above

Description : The bounded Quantization error is also called__________. A. overload error B. overload noise C. granular error D. All of above

Last Answer : C. granular error

Describe slope overload and granular noise in DM system

Description : Describe slope overload and granular noise in DM system

Last Answer : SLOPE-OVERLOAD DISTORTION: If the slope of the analog signal x(t) is much higher (steep) than that of the approximated signal xq(t) over a long duration then xq(t) will not follow x(t) ... , the step size should be as small as possible. However, this will increase slope-overload distortion.

What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Description : What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Last Answer : D. To protect small signals in PCM from quantizing distortion

What is the non-continuous noise of irregular pulses or spikes of duration with high amplitudes? A. Wander B. Jitter C. Hits D. Singing

Description : What is the non-continuous noise of irregular pulses or spikes of duration with high amplitudes? A. Wander B. Jitter C. Hits D. Singing

Last Answer : B. Jitter

In data communication the transmission of binary signals will require _______. A. Same bandwidth as analog B. More bandwidth than analog C. Less bandwidth than analog D. Bigger cable diameter

Description : In data communication the transmission of binary signals will require _______. A. Same bandwidth as analog B. More bandwidth than analog C. Less bandwidth than analog D. Bigger cable diameter

Last Answer : B. More bandwidth than analog

_______ are deep valleys with cliffs or steep slopes along their sides.?

Description : _______ are deep valleys with cliffs or steep slopes along their sides.?

Last Answer : They are canyons

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : B. The approximation of the quantized signal

Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Description : Which causes a quantization noise in PCM system? A. Serial transmission errors B. The approximation of the quantized signal C. The synchronization between encoder and decoder D. Binary coding techniques

Last Answer : The approximation of the quantized signal

What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Description : What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Last Answer : B. 50 dB

Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Description : Quantization noise is caused by A. binary coding techniques B. serial transmission errors C. the synchronization between encoder and decoder D. the approximation of the quantized signal

Last Answer : D. the approximation of the quantized signal

External noise fields are measured in terms of _______. A. rms values B. dc values C. average values D. peak values

Description : External noise fields are measured in terms of _______. A. rms values B. dc values C. average values D. peak values

Last Answer : D. peak values

Can camels climb steep slopes or mountains?

Description : Can camels climb steep slopes or mountains?

Last Answer : A: Camels are not well-suited for climbing steep slopes or mountains. Their anatomy and body structure are more adapted for walking on flat terrains and sandy deserts rather than navigating rugged, mountainous terrains.

How can soil erosion be slowed on steep slopes?

Description : How can soil erosion be slowed on steep slopes?

Last Answer : By planting weeds, bushes, trees, etc., the roots help hold thesoil in place.

Khaddar soils are found (a) in piedmont plains (b) in flood plains (c) over low plateaux (d) over steep slopes

Description : Khaddar soils are found (a) in piedmont plains (b) in flood plains (c) over low plateaux (d) over steep slopes

Last Answer : Ans: (b)

Landslides occur because of? a. Intensity of rainfall b. Steep slopes c. Deforestation leading it soil erosion d. All the above

Description : Landslides occur because of? a. Intensity of rainfall b. Steep slopes c. Deforestation leading it soil erosion d. All the above

Last Answer : d. All the above

All of the following are TRUE of the Paricutin volcano except w) its slopes are steep x) it is a lava cone y) it is located in Mexico z) it was built over a short period of time

Description : All of the following are TRUE of the Paricutin volcano except w) its slopes are steep x) it is a lava cone y) it is located in Mexico z) it was built over a short period of time

Last Answer : ANSWER: X -- IT IS A LAVA CONE

Digital transmission provides a higher level of signal quality than analog transmission because A. repeaters regenerate digital pulses and remove distorstion B. digital signals are easier to sample than analog signals C. digital signals are smaller than analog signals and cannot easily be distorted D. analog signals are continuous and not easily distorted.

Description : Digital transmission provides a higher level of signal quality than analog transmission because A. repeaters regenerate digital pulses and remove distorstion B. digital signals are easier to sample than ... and cannot easily be distorted D. analog signals are continuous and not easily distorted.

Last Answer : A. repeaters regenerate digital pulses and remove distorstion

Noise occurring in the presence of signal resulting from a mismatch between the exact value of an analog signal and the closet available quantizing step in a digital coder. A. Quantizing noise B. Thermal noise C. Impulse noise D. Crosstalk

Description : Noise occurring in the presence of signal resulting from a mismatch between the exact value of an analog signal and the closet available quantizing step in a digital coder. A. Quantizing noise B. Thermal noise C. Impulse noise D. Crosstalk

Last Answer : A. Quantizing noise

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

_________ is the random and unpredictable electric signals from natural causes, both internal and external to the system. A. Interference B. Attenuation C. Distortion D. Noise

Description : _________ is the random and unpredictable electric signals from natural causes, both internal and external to the system. A. Interference B. Attenuation C. Distortion D. Noise

Last Answer : D. Noise

An advantage of optic fiber rejecting an induced noise signals from magnetic field or solar storms flux. A. Electric hazard B. Cross talk C. Immunity to noise D. Shielding

Description : An advantage of optic fiber rejecting an induced noise signals from magnetic field or solar storms flux. A. Electric hazard B. Cross talk C. Immunity to noise D. Shielding

Last Answer : C. Immunity to noise

What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Description : What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Last Answer : B. The combination of two signals to produce sum and difference frequencies.

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Choosing a discrete value that is near but not exactly at the analog signal level leads to a) PCM error b) Quantization error c) PAM error d) Sampling error

Description : Choosing a discrete value that is near but not exactly at the analog signal level leads to a) PCM error b) Quantization error c) PAM error d) Sampling error

Last Answer : b) Quantization error

The process of dividing an analog signal into a string of discrete outputs, each of constant amplitude, is called: (A) Strobing (B) Amplification (C) Conditioning (D) Quantization

Description : The process of dividing an analog signal into a string of discrete outputs, each of constant amplitude, is called: (A) Strobing (B) Amplification (C) Conditioning (D) Quantization

Last Answer : (D) Quantization

Which of the following steps is/are not required for analog to digital conversion ? (a) Sensing (b) Conversion (c) Amplification (d) Conditioning (e) Quantization Codes : (A) (a) and (b) (B) (c) and (d) (C) (a), (b) and (e) (D) None of the above

Description : Which of the following steps is/are not required for analog to digital conversion ? (a) Sensing (b) Conversion (c) Amplification (d) Conditioning (e) Quantization Codes : (A) (a) and (b) (B) (c) and (d) (C) (a), (b) and (e) (D) None of the above

Last Answer : (D) None of the above

Define quantization error.

Description : Define quantization error.

Last Answer : In A/D converter the smallest digital step is due to the LSB and it can be made smaller only by increasing the number of bits in the digital representation. This error is called quantization error.

Data from a computer are_______; the local loop handles _______ signals. A) analog; analog B) analog; digital C) digital; digital D) digital; analog

Description : Data from a computer are_______; the local loop handles _______ signals. A) analog; analog B) analog; digital C) digital; digital D) digital; analog

Last Answer : digital; analog

_______ signals canhave only alimited number of values. A) Analog B) Digital C) (a) or (b) D) None of the above

Description : _______ signals canhave only alimited number of values. A) Analog B) Digital C) (a) or (b) D) None of the above

Last Answer : Digital

ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the same as that of the intermediate frequency C. Generates a 1kHz note for Morse code reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

In what region of the world is sporadic-E most prevalent? A. The equatorial regions B. The northern hemisphere C. The arctic regions D. The polar regions

Description : In what region of the world is sporadic-E most prevalent? A. The equatorial regions B. The northern hemisphere C. The arctic regions D. The polar regions

Last Answer : A. The equatorial regions

How do contour lines show a steep slope?

Description : How do contour lines show a steep slope?

Last Answer : The closer together the lines are - the steeper the slope.

What is a material that accumulates at the bottom of a steep slope?

Description : What is a material that accumulates at the bottom of a steep slope?

Last Answer : The general term for material that falls down and gathers at the foot of a steep cliff or mountain face is scree.

How do contour lines show a steep slope?

Description : How do contour lines show a steep slope?

Last Answer : The closer together the lines are - the steeper the slope.

A steep slope on a phase change graph indicates?

Description : A steep slope on a phase change graph indicates?

Last Answer : Heirhey

Landslides occur because ofA) Rainfall B) Steep slope C) Deforestation D) All of the above.

Description : Landslides occur because of A) Rainfall B) Steep slope C) Deforestation D) All of the above.

Last Answer : D) All of the above.

What causes convective acceleration in fluid flow? (A) Steep slope in flow (B) Unsteady nature of flow (C) Non-uniformity of flow (D) Turbulence in flow

Description : What causes convective acceleration in fluid flow? (A) Steep slope in flow (B) Unsteady nature of flow (C) Non-uniformity of flow (D) Turbulence in flow

Last Answer : (C) Non-uniformity of flow

A series of closely spaced contour lines represents a (A) Steep slope (B) Gentle slope (C) Uniform slope (D) Plane surface

Description : A series of closely spaced contour lines represents a (A) Steep slope (B) Gentle slope (C) Uniform slope (D) Plane surface

Last Answer : (A) Steep slope

Pick up the correct statement from the following: (A) The throat of the section of a control meter is either rectangular or trapezoidal (B) The floor of the control meter throat is almost level (C) The floor of the expanding outlet of the control meter is given a steep slope (D) All the above

Description : Pick up the correct statement from the following: (A) The throat of the section of a control meter is either rectangular or trapezoidal (B) The floor of the control meter throat is almost level (C) The floor of the expanding outlet of the control meter is given a steep slope (D) All the above

Last Answer : Answer: Option D

If the cross slope of a country is 25% to 60%, the terrain is classified as (A) Plain (B) Rolling (C) Steep (D) Mountainous

Description : If the cross slope of a country is 25% to 60%, the terrain is classified as (A) Plain (B) Rolling (C) Steep (D) Mountainous

Last Answer : Answer: Option D

If cross slope of a country is 10% to 25%, the terrain is classified as (A) Rolling (B) Mountainous (C) Steep (D) Plain

Description : If cross slope of a country is 10% to 25%, the terrain is classified as (A) Rolling (B) Mountainous (C) Steep (D) Plain

Last Answer : Answer: Option A

If cross slope of a country is upto 10% the terrain is classified as (A) Plain (B) Rolling (C) Mountainous (D) Steep

Description : If cross slope of a country is upto 10% the terrain is classified as (A) Plain (B) Rolling (C) Mountainous (D) Steep

Last Answer : Answer: Option A

If cross slope of a country is greater than 60%, the terrain is classified as(A) Rolling (B) Mountainous (C) Steep (D) Plain

Description : If cross slope of a country is greater than 60%, the terrain is classified as (A) Rolling (B) Mountainous (C) Steep (D) Plain

Last Answer : Answer: Option C

A man builds a house rectangular in shape. All sides have southern exposure. A bear walks by the house. What color is the bear? Why? (This one could drive you nuts and should only be attempted by those with high self esteem. If you are seeing a therapist, DO NOT ATTEMPT THIS QUESTION!) ...black...bears are black ...white... ...brown...the house is on a steep slope There is no answer and this is a stupid question.

Description : A man builds a house rectangular in shape. All sides have southern exposure. A bear walks by the house. What color is the bear? Why? (This one could drive you nuts and should only be attempted by those ... ..brown...the house is on a steep slope There is no answer and this is a stupid question.

Last Answer : ..white...

In marketing channels, conflict occurs in marketing channels working at same level is classified as A. steep conflict B. slope conflict C. vertical conflict D. horizontal conflict

Description : In marketing channels, conflict occurs in marketing channels working at same level is classified as A. steep conflict B. slope conflict C. vertical conflict D. horizontal conflict

Last Answer : D. horizontal conflict

A series of closely spaced contour lines represent a (a) Steep slope* (b) Gentle slope (c) Uniform slope (d) Plane surface

Description : A series of closely spaced contour lines represent a (a) Steep slope* (b) Gentle slope (c) Uniform slope (d) Plane surface

Last Answer : (a) Steep slope*