The signal to noise ratio that is required for a satisfactory television reception. A. 30 dB B. 40 dB C. 10 dB D. 20 dB

The signal to noise ratio that is required for a satisfactory television reception.
A. 30 dB
B. 40 dB
C. 10 dB
D. 20 dB
by

1 Answer

Answer :

B. 40 dB
by

Related questions

What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Last Answer : C. 40 dB

What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Last Answer : A. 50 dB

Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Description : Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Last Answer : A. 5.23 dB

What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Description : What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Last Answer : B. 50 dB

What region around a broadcasting transmitter in which satisfactory reception of broadcasting signal is not obtained? A. Fringe area B. Primary are C. Secondary area D. Tertiary area

Description : What region around a broadcasting transmitter in which satisfactory reception of broadcasting signal is not obtained? A. Fringe area B. Primary are C. Secondary area D. Tertiary area

Last Answer : A. Fringe area

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Description : The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Last Answer : D. 14 dB

The total space loss of transmission and reception for two ground stations with uplink frequency 8GHz and a downlink of 6 GHz with angle of elevations of 3˚ and 7˚ A respectively is A. 403 dB B. 100 dB C. 20 dB D. 215 dB

Description : The total space loss of transmission and reception for two ground stations with uplink frequency 8GHz and a downlink of 6 GHz with angle of elevations of 3˚ and 7˚ A respectively is A. 403 dB B. 100 dB C. 20 dB D. 215 dB

Last Answer : A. 403 dB

A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Last Answer : D. 8.8 dB

What is the number of levels required in a PCM system with S/N ratio of 40 dB? A. 64 B. 128 C. 256 D. 512

Description : What is the number of levels required in a PCM system with S/N ratio of 40 dB? A. 64 B. 128 C. 256 D. 512

Last Answer : B. 128

The noise from an airplane engine 100 ft from an observer is found to have an intensity of 45dB. What will be the intensity when the plane flies overhead at an altitude of 1 mi? A. 10.5 dB B. 34.5 dB C. 35 dB D. 20.5 dB

Description : The noise from an airplane engine 100 ft from an observer is found to have an intensity of 45dB. What will be the intensity when the plane flies overhead at an altitude of 1 mi? A. 10.5 dB B. 34.5 dB C. 35 dB D. 20.5 dB

Last Answer : A. 10.5 dB

Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Description : Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Last Answer : B. 6 dB

You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Description : You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Last Answer : C. 25

You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Description : You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Last Answer : C. 35

A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW. What is the gain in dB, obtained by the use if the reflector. (Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Description : A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW ... Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Last Answer : B. 2.6

A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 kW. What is the gain in dB obtain by the use of the reflector ? ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Description : A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 ... ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Last Answer : D. 2.6

The agreed standard for measuring loudness is the loudness sensation produced by a 1000 Hz sine wave _____ dB above the listener’s threshold of hearing. A. 80 B. 50 C. 30 D. 40

Description : The agreed standard for measuring loudness is the loudness sensation produced by a 1000 Hz sine wave _____ dB above the listener’s threshold of hearing. A. 80 B. 50 C. 30 D. 40

Last Answer : D. 40

The noise figure of the first circuit in tandem connection is 10.5 dB while its power gain is 15, what is the over all noise figure if the second circuit has a noise figure of 11 dB? A. 11.59 dB B. 11.23 dB C. 10.79 dB D. 10.5 dB

Description : The noise figure of the first circuit in tandem connection is 10.5 dB while its power gain is 15, what is the over all noise figure if the second circuit has a noise figure of 11 dB? A. 11.59 dB B. 11.23 dB C. 10.79 dB D. 10.5 dB

Last Answer : C. 10.79 dB

What is the front-to-back ratio of an antenna which radiates 500 watts in a northernly direction and 50 watts in a southernly direction? A. 25000 dB B. 10 dB C. 100 dB D. 20 dB

Description : What is the front-to-back ratio of an antenna which radiates 500 watts in a northernly direction and 50 watts in a southernly direction? A. 25000 dB B. 10 dB C. 100 dB D. 20 dB

Last Answer : B. 10 dB

At what loudness level do pitch (in mels) and frequency (in Hz) are numerically equal? A. 0 dB B. 20 dB C. 60 dB D. 40 dB

Description : At what loudness level do pitch (in mels) and frequency (in Hz) are numerically equal? A. 0 dB B. 20 dB C. 60 dB D. 40 dB

Last Answer : D. 40 dB

if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Description : if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Last Answer : Answers is the place to go to get the answers you need and to ask the questions you want

Stacking antennas at various angles results in A. a more omnidirectional reception B. a more unidirectional reception C. a more omnidirectional reception D. an overall reception signal increase

Description : Stacking antennas at various angles results in A. a more omnidirectional reception B. a more unidirectional reception C. a more omnidirectional reception D. an overall reception signal increase

Last Answer : A. a more omnidirectional reception

What is the method of diversity reception where the signal is transmitted on 2 different frequencies over the same path? A. Quadruple B. Frequency C. Polarization D. Space

Description : What is the method of diversity reception where the signal is transmitted on 2 different frequencies over the same path? A. Quadruple B. Frequency C. Polarization D. Space

Last Answer : B. Frequency

ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the same as that of the intermediate frequency C. Generates a 1kHz note for Morse code reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Description : Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Last Answer : A. 1.6 dB

You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Last Answer : D. 32

Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Description : Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Last Answer : C. dBmc

In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Last Answer : B. 93

A reading of -50 dBm on the disturbing pair, and -80 on the disturbed pair equals _____ dB of crosstalk coupling. A. 20 B. 30 C. 60 D. 25

Description : A reading of -50 dBm on the disturbing pair, and -80 on the disturbed pair equals _____ dB of crosstalk coupling. A. 20 B. 30 C. 60 D. 25

Last Answer : B. 30

Part of a microwave link can be approximated by free space conditions. The antenna gain are each 40 dB, the frequency is 10 GHz, and the path length is 80 km. Calculate the receive power for a transmitted power of 10 W? A. 0.871 μW B. 871 μW C. 0.871 mW D. 871 nW

Description : Part of a microwave link can be approximated by free space conditions. The antenna gain are each 40 dB, the frequency is 10 GHz, and the path length is 80 km. Calculate the receive power for a transmitted power of 10 W? A. 0.871 μW B. 871 μW C. 0.871 mW D. 871 nW

Last Answer : A. 0.871 μW

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Last Answer : C. In the receiver front end

What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Description : What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Last Answer : C. Poor front-end selectivity

What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Description : What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Last Answer : B. 3853 Hz

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Last Answer : C. In the receiver front end

Acceptable "Noise Pollution Level" in India range between: (1) 16 - 35 db (2) 40 - 45 db (3) 70 - 100 db (4) 10 - 15 db

Description : Acceptable "Noise Pollution Level" in India range between: (1) 16 - 35 db (2) 40 - 45 db (3) 70 - 100 db (4) 10 - 15 db

Last Answer : (2) 40 - 45 db Explanation: According to the noise pollution rules, the permissible noise level during the day is 50dB in silence zones, 55dB in residential areas, 65 dB in commercial areas and 75 ... areas, commercial areas and industrial areas are respectively 40 dB, 45 dB, 55 dB and 70 dB.

Atmospheric noise or static is not a great problem A. at frequencies below 20 MHz B. at frequencies below 5 MHz C. at frequencies above 30 MHz D. at frequencies above 1 MHz

Description : Atmospheric noise or static is not a great problem A. at frequencies below 20 MHz B. at frequencies below 5 MHz C. at frequencies above 30 MHz D. at frequencies above 1 MHz

Last Answer : C. at frequencies above 30 MHz

Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?

Description : Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?

Last Answer : 35-dB RMS because the highest SNR can always record and reproduce the widest range of input signals.

What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Last Answer : C. 125,000

Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Description : Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Last Answer : A. 75

What is the data rate in Mbps of a single satellite transponder considering an S/N of 30 dB? A. 35.8 B. 3.58 C. 358 D. 3580

Description : What is the data rate in Mbps of a single satellite transponder considering an S/N of 30 dB? A. 35.8 B. 3.58 C. 358 D. 3580

Last Answer : C. 358

Determine the gain of a 6 ft. parabolic dish operating at 1800 MHz. A. 30 dB B. 11.2 dB C. 15.5 dB D. 28.17 dB

Description : Determine the gain of a 6 ft. parabolic dish operating at 1800 MHz. A. 30 dB B. 11.2 dB C. 15.5 dB D. 28.17 dB

Last Answer : D. 28.17 dB

Lightning rods must be mounted a top structure not less than ___ above the highest point. A. 10 cm B. 20 cm C. 30 cm D. 40 cm

Description : Lightning rods must be mounted a top structure not less than ___ above the highest point. A. 10 cm B. 20 cm C. 30 cm D. 40 cm

Last Answer : C. 30 cm

In the American standard, the aural transmitter maximum radiated power is _____ of peak visual transmitter power. A. 10 % B. 30 % C. 20 % D. 40 %

Description : In the American standard, the aural transmitter maximum radiated power is _____ of peak visual transmitter power. A. 10 % B. 30 % C. 20 % D. 40 %

Last Answer : C. 20 %

For a sample rate of 40 kHz, determine the maximum analog input frequency A. 30 kHz B. 40 kHz C. 20 kHz D. 10 kHz

Description : For a sample rate of 40 kHz, determine the maximum analog input frequency A. 30 kHz B. 40 kHz C. 20 kHz D. 10 kHz

Last Answer : C. 20 kHz

What is the equivalent output of a circuit in dBm, if it is has an output of 10 watts? A. 10 dBm B. 30 dBm C. 20 dBm D. 40 dBm

Description : What is the equivalent output of a circuit in dBm, if it is has an output of 10 watts? A. 10 dBm B. 30 dBm C. 20 dBm D. 40 dBm

Last Answer : D. 40 dBm

Ethernet is baseband system using CSMA/CD operating at A. 20 Mbps B. 10 Mbps C. 30 Mbps D. 40 Mbps

Description : Ethernet is baseband system using CSMA/CD operating at A. 20 Mbps B. 10 Mbps C. 30 Mbps D. 40 Mbps

Last Answer : B. 10 Mbps

Three telephone circuits, each having an S/N ratio of 44 dB, are connected in tandem. What is the overall S/N ratio? A. 44 dB B. 39.2 dB C. 41 dB D. 43.52 dB

Description : Three telephone circuits, each having an S/N ratio of 44 dB, are connected in tandem. What is the overall S/N ratio? A. 44 dB B. 39.2 dB C. 41 dB D. 43.52 dB

Last Answer : B. 39.2 dB