The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

The signal in a channel is measured to be 23 dB while noise in the same channel is
measured to be 9 dB. The signal to noise ratio therefore is __________.
A. 9/23
B. 23/9
C. 32 dB
D. 14 dB
by

1 Answer

Answer :

D. 14 dB
by

Related questions

Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Description : Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Last Answer : A. 5.23 dB

You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Last Answer : D. 32

You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Description : You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Last Answer : C. 35

The noise figure of the first circuit in tandem connection is 10.5 dB while its power gain is 15, what is the over all noise figure if the second circuit has a noise figure of 11 dB? A. 11.59 dB B. 11.23 dB C. 10.79 dB D. 10.5 dB

Description : The noise figure of the first circuit in tandem connection is 10.5 dB while its power gain is 15, what is the over all noise figure if the second circuit has a noise figure of 11 dB? A. 11.59 dB B. 11.23 dB C. 10.79 dB D. 10.5 dB

Last Answer : C. 10.79 dB

What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Last Answer : C. 40 dB

What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Description : What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Last Answer : B. 50 dB

The signal to noise ratio that is required for a satisfactory television reception. A. 30 dB B. 40 dB C. 10 dB D. 20 dB

Description : The signal to noise ratio that is required for a satisfactory television reception. A. 30 dB B. 40 dB C. 10 dB D. 20 dB

Last Answer : B. 40 dB

What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Last Answer : A. 50 dB

In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Last Answer : B. 93

A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Last Answer : D. 8.8 dB

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Description : You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Last Answer : C. 38 dBa

Noise always affects the signal in a communications systems at the ________. A. transmitter B. channel C. information source D. destination

Description : Noise always affects the signal in a communications systems at the ________. A. transmitter B. channel C. information source D. destination

Last Answer : B. channel

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW. What is the gain in dB, obtained by the use if the reflector. (Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Description : A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW ... Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Last Answer : B. 2.6

A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 kW. What is the gain in dB obtain by the use of the reflector ? ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Description : A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 ... ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Last Answer : D. 2.6

if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Description : if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Last Answer : Answers is the place to go to get the answers you need and to ask the questions you want

The value of the resistor creating thermal noise is doubled. The noise power generated is therefore. A. halved B. quadrupled C. doubled D. unchanged

Description : The value of the resistor creating thermal noise is doubled. The noise power generated is therefore. A. halved B. quadrupled C. doubled D. unchanged

Last Answer : D. unchanged

Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Description : Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Last Answer : A. 75

What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 37.6 W B. 237 W C. 150 W D. 23.7 W

Last Answer : A. 37.6 W

Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Description : Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Last Answer : A. 1.6 dB

You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Description : You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Last Answer : C. 25

Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Description : Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Last Answer : C. dBmc

The noise from an airplane engine 100 ft from an observer is found to have an intensity of 45dB. What will be the intensity when the plane flies overhead at an altitude of 1 mi? A. 10.5 dB B. 34.5 dB C. 35 dB D. 20.5 dB

Description : The noise from an airplane engine 100 ft from an observer is found to have an intensity of 45dB. What will be the intensity when the plane flies overhead at an altitude of 1 mi? A. 10.5 dB B. 34.5 dB C. 35 dB D. 20.5 dB

Last Answer : A. 10.5 dB

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Last Answer : C. In the receiver front end

What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Description : What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Last Answer : C. Poor front-end selectivity

What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Description : What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Last Answer : B. 3853 Hz

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Last Answer : C. In the receiver front end

You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Description : You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Last Answer : C. 22

Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Description : Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Last Answer : B. 6 dB

A two digit number is such that the sum of the digits is 11.When the number with the same digits is reversed is subtracted from this number, the difference is 9.What is the number? 1. 23 2. 24 3. 65 4. 14 5. 32

Description : A two digit number is such that the sum of the digits is 11.When the number with the same digits is reversed is  subtracted from this number, the difference is 9.What is the number? 1. 23 2. 24 3. 65 4. 14 5. 32

Last Answer : Answer- 3(65) Explanation:- let the number be written as xy x-ten’s place y units place x+y=11…………………1 (10x+y)-(10y+x)=9 10x+y-10y-x=9 9x-9y=9 x-y=1………………….2 Add (1) & (2) 2x=12 x=6 y=5 the number is 65

Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Description : Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Last Answer : D. B and C above

The sound intensity received from the nearby jet plane is 12.6 µW/m2 and that from another jet plane some distance away is 0.45 µW/m2 . Find the relative loudness of the two. A. 14.0 dB B. 14.5dB C. 12.5 D. 14.5

Description : The sound intensity received from the nearby jet plane is 12.6 µW/m2 and that from another jet plane some distance away is 0.45 µW/m2 . Find the relative loudness of the two. A. 14.0 dB B. 14.5dB C. 12.5 D. 14.5

Last Answer : B. 14.5dB

The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is

Description : The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is

Last Answer : The capacity of a standard 4 KHz telephone channel with a 32 dB SNR is 32953 bits/second

Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?

Description : Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?

Last Answer : 35-dB RMS because the highest SNR can always record and reproduce the widest range of input signals.

1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Description : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Last Answer : 22

The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Description : The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Last Answer : D. All of the above

Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Description : Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Last Answer : B. Impulse noise voltage is dependent on bandwidth

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

External noise fields are measured in terms of _______. A. rms values B. dc values C. average values D. peak values

Description : External noise fields are measured in terms of _______. A. rms values B. dc values C. average values D. peak values

Last Answer : D. peak values

_________ is measured on a circuit when it is correctly terminated but does not have any traffic. A. White noise B. Galactic noise C. Impulse noise D. Atmospheric noise

Description : _________ is measured on a circuit when it is correctly terminated but does not have any traffic. A. White noise B. Galactic noise C. Impulse noise D. Atmospheric noise

Last Answer : A. White noise

A signal is measured at two different points. The power is P1 at the first point and P2 at the second point. The dB is 0. This means________. A) P2 is zero B) P2 equals P1 C) P2 is much larger than P1 D) P2 is much smaller than P1

Description : A signal is measured at two different points. The power is P1 at the first point and P2 at the second point. The dB is 0. This means________. A) P2 is zero B) P2 equals P1 C) P2 is much larger than P1 D) P2 is much smaller than P1

Last Answer : P2 equals P1

What is the front-to-back ratio of an antenna which radiates 500 watts in a northernly direction and 50 watts in a southernly direction? A. 25000 dB B. 10 dB C. 100 dB D. 20 dB

Description : What is the front-to-back ratio of an antenna which radiates 500 watts in a northernly direction and 50 watts in a southernly direction? A. 25000 dB B. 10 dB C. 100 dB D. 20 dB

Last Answer : B. 10 dB

What is the number of levels required in a PCM system with S/N ratio of 40 dB? A. 64 B. 128 C. 256 D. 512

Description : What is the number of levels required in a PCM system with S/N ratio of 40 dB? A. 64 B. 128 C. 256 D. 512

Last Answer : B. 128

Three telephone circuits, each having an S/N ratio of 44 dB, are connected in tandem. What is the overall S/N ratio? A. 44 dB B. 39.2 dB C. 41 dB D. 43.52 dB

Description : Three telephone circuits, each having an S/N ratio of 44 dB, are connected in tandem. What is the overall S/N ratio? A. 44 dB B. 39.2 dB C. 41 dB D. 43.52 dB

Last Answer : B. 39.2 dB

What is the gain of an antenna over a half-wavelength dipole when it has 6 dB gain over an isotropic radiator? A. 6.0 dB B. 8.1 dB C. 3.9 dB D. 10.0 dB

Description : What is the gain of an antenna over a half-wavelength dipole when it has 6 dB gain over an isotropic radiator? A. 6.0 dB B. 8.1 dB C. 3.9 dB D. 10.0 dB

Last Answer : C. 3.9 dB