Best describe as an amplifier used in radio telephony. A. Magnifier B. Class B C. Class C D. Class A

Best describe as an amplifier used in radio telephony.
A. Magnifier
B. Class B
C. Class C
D. Class A
by

1 Answer

Answer :

C. Class C
by

Related questions

Which of the following is designated as the international distress, safety and calling frequency for radio telephony for stations of the maritime mobile service when using frequencies in the authorized bands between 156 and 174 MHz? A. 165.8 MHz B. 156.8 MHz C. 158.6 MHz D. 168.5 MHz

Description : Which of the following is designated as the international distress, safety and calling frequency for radio telephony for stations of the maritime mobile service when using frequencies in the authorized bands between 156 and 174 MHz? A. 165.8 MHz B. 156.8 MHz C. 158.6 MHz D. 168.5 MHz

Last Answer : B. 156.8 MHz

What is the term used in telephony and telegraphy for irregular disturbing radiation due to various causes and in a particular produced by arc transmitters causing a rushing sound in receiving telephones? A. Fax tone B. Mush C. Hiss D. Crosstalk

Description : What is the term used in telephony and telegraphy for irregular disturbing radiation due to various causes and in a particular produced by arc transmitters causing a rushing sound in receiving telephones? A. Fax tone B. Mush C. Hiss D. Crosstalk

Last Answer : B. Mush

Technical study which deals with production, transport and delivery of a quality signal from source to destination. A. Transmission system engineering B. Communication system engineering C. Telephony engineering D. Telegraphic engineering

Description : Technical study which deals with production, transport and delivery of a quality signal from source to destination. A. Transmission system engineering B. Communication system engineering C. Telephony engineering D. Telegraphic engineering

Last Answer : A. Transmission system engineering

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

Referred to as the stage in the radio receiver that contributes most of the noise. A. IF amplifier B. Supply stage C. Speaker D. Mixer

Description : Referred to as the stage in the radio receiver that contributes most of the noise. A. IF amplifier B. Supply stage C. Speaker D. Mixer

Last Answer : D. Mixer

Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Description : Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Last Answer : A. 1.0025 MHz

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

The final power amplifier in an FM transmitter usually operates class ______. A. AB B. C C. B D. A

Description : The final power amplifier in an FM transmitter usually operates class ______. A. AB B. C C. B D. A

Last Answer : B. C

The final amplifier of either FM or AM transmitter operates as A. Class B B. Class C C. Class A D. Class D

Description : The final amplifier of either FM or AM transmitter operates as A. Class B B. Class C C. Class A D. Class D

Last Answer : B. Class C

According to KBP revised radio code which airtime below is classified class D for AM stations? A. 6:00 AM to 12:00 NN B. 12:00 NN to 6:00 PM C. 9:00 PM to 12 Midnight D. 12:00 Midnight to 5:00 AM

Description : According to KBP revised radio code which airtime below is classified class D for AM stations? A. 6:00 AM to 12:00 NN B. 12:00 NN to 6:00 PM C. 9:00 PM to 12 Midnight D. 12:00 Midnight to 5:00 AM

Last Answer : D. 12:00 Midnight to 5:00 AM

What is a magnifier ? What is a magnifier ?

Description : What is a magnifier ? What is a magnifier ?

Last Answer : A magnifier is an electronics device that receives the signal applied to the input in amplified output.

What is an operational magnifier ? What is an operational magnifier ?

Description : What is an operational magnifier ? What is an operational magnifier ?

Last Answer : : A negative direct feedback magnifier with very high gain is called an operational magnifier.

What is a multi-step magnifier ?

Description : What is a multi-step magnifier ?

Last Answer : A series of two or more magnifiers to increase magnification.

What is Magnifier of the image of small objects?

Description : What is Magnifier of the image of small objects?

Last Answer : What is the answer ?

Where to purchase hand held magnifier 3x, 4x, with light Hervey Bay area or Brisbane?

Description : Where to purchase hand held magnifier 3x, 4x, with light Hervey Bay area or Brisbane?

Last Answer : I think Booksplendour caries them to help people read Pullenvale 103 Grandview Road, Brisbane QLD 4069, Australia - (07) 3202 7547

Electron Microscope is more magnifier than light microscope because –

Description : Electron Microscope is more magnifier than light microscope because –

Last Answer : Wavelength of electron is less than the wavelength of light

What do you understand by linear magnification and angular magnification? Explain how a convex lens is used as a magnifier?

Description : What do you understand by linear magnification and angular magnification? Explain how a convex lens is used as a magnifier?

Last Answer : Linear Magnification: The ratio of the size of image to the size of object is called linear magnification. Angular magnification: The ratio of the angle subtended by the image as seen through the optical ... lens used as a magnifier when an object is brought within the focal length of convex lens.

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

Which of the following antennas is used for testing and adjusting a transmitter for proper modulation, amplifier operation and frequency accuracy? A. Elementary B. Real C. Isotropic D. Dummy

Description : Which of the following antennas is used for testing and adjusting a transmitter for proper modulation, amplifier operation and frequency accuracy? A. Elementary B. Real C. Isotropic D. Dummy

Last Answer : D. Dummy

Which circuit contributes most of the noise in a receiver? A. IF amplifier B. Demodulator C. AF amplifier D. Mixer

Description : Which circuit contributes most of the noise in a receiver? A. IF amplifier B. Demodulator C. AF amplifier D. Mixer

Last Answer : D. Mixer

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Description : Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Last Answer : A. 39.4

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant, what does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, respectively. Calculate the equivalent input-noise resistance of this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

What is the reliable measurement for comparing amplifier noise characteristics? A. Thermal agitation noise B. Noise factor C. Noise margin D. Signal-to-noise

Description : What is the reliable measurement for comparing amplifier noise characteristics? A. Thermal agitation noise B. Noise factor C. Noise margin D. Signal-to-noise

Last Answer : B. Noise factor

What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Description : What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Last Answer : C. Video detector

When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Last Answer : D. final RF stage

What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Description : What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Last Answer : A. The power traveling from the transmitter to the antenna.

What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Last Answer : D. IF amplifier

What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

Referred to an oscillator signal “leak through” from a properly neutralized amplifier such as a master oscillator power amplifier. A. Carrier B. Stray signal C. Back wave D. Loss wave

Description : Referred to an oscillator signal “leak through” from a properly neutralized amplifier such as a master oscillator power amplifier. A. Carrier B. Stray signal C. Back wave D. Loss wave

Last Answer : C. Back wave

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Description : What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Last Answer : A. Low noise amplifier

Define non-inverting amplifier?

Description : Define non-inverting amplifier?

Last Answer : The input is applied to the non-inverting input terminal and the inverting terminal connected to the ground.

List the applications of instrumentation amplifier.

Description : List the applications of instrumentation amplifier.

Last Answer : a. Temperature indicator b. Temperature controller c. Light intensity meters d. Water flow meter c. Thermal conductivity meter f. Analog weight scale

What is the type of feedback employed in the inverting op-amp amplifier?

Description : What is the type of feedback employed in the inverting op-amp amplifier?

Last Answer : Negative feedback is employed in the inverting op-amp amplifier.

Which feedback increases the gain of the amplifier?

Description : Which feedback increases the gain of the amplifier?

Last Answer : Positive feedback

Which feedback decreases the gain of the amplifier?

Description : Which feedback decreases the gain of the amplifier?

Last Answer : Negative feed back

How can a AC equivalent circuit of a amplifier be obtained?

Description : How can a AC equivalent circuit of a amplifier be obtained?

Last Answer : By replacing dc supply by a ground and short- circuiting capacitors.

How can a DC equivalent circuit of an amplifier be obtained?

Description : How can a DC equivalent circuit of an amplifier be obtained?

Last Answer : By open circuiting the capacitor.

What is an amplifier?

Description : What is an amplifier?

Last Answer : An amplifier is a device which produces a large electrical output of similar characteristics to that of the input parameters.

What are the basic rules of an operating amplifier?

Description : What are the basic rules of an operating amplifier?

Last Answer : The operating point should be fixed on the load line. The upper end of the load line lies on the saturation region &lower end lies on the cutoff region.