Give the classification of phase detector:

Give the classification of phase detector:
by

1 Answer

Answer :

1.Analog phase detector .

2.Digital phase detector
by

Related questions

A particular circuit that rids FM of noise A. Detector B. Discriminator C. Phase Shifter D. Limiter

Description : A particular circuit that rids FM of noise A. Detector B. Discriminator C. Phase Shifter D. Limiter

Last Answer : D. Limiter

What are the problems associated with switch type phase detector?

Description : What are the problems associated with switch type phase detector?

Last Answer : 1.The output voltage Ve is proportional to the input signal amplitude.This is undesirable because it makes phase detector gain and loop gain dependent on the input signal amplitude. 2.The output is proportional to cosQ making it non linear.

What is a switch type phase detector?

Description : What is a switch type phase detector?

Last Answer : An electronic switch is opened and closed by signal coming from VCO and the input signal is chopped at a repetition rate determined by the VCO frequency.This type of phase detector is called a ... detector since the phase information for only one half of the input signal is detected and averaged.

What is a device that detects both vertically and horizontally polarized signals simultaneously? A. Orthomode transducer B. Crystal detector C. Optoisolator D. Isomode detector

Description : What is a device that detects both vertically and horizontally polarized signals simultaneously? A. Orthomode transducer B. Crystal detector C. Optoisolator D. Isomode detector

Last Answer : A. Orthomode transducer

What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Description : What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Last Answer : C. Video detector

Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Description : What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Last Answer : D. Photovoltaic effect

A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Description : A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Last Answer : A. Noise equivalent power

If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Description : If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Last Answer : A. 34.61 ns

The most common device used as a light detector in fiber optic communications system. A. LED B. Darlington phototransistor C. APDs D. PIN diode

Description : The most common device used as a light detector in fiber optic communications system. A. LED B. Darlington phototransistor C. APDs D. PIN diode

Last Answer : C. APDs

If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Description : If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Last Answer : A. 14 ns

Combination of modulator, channel and detector. A. Transceiver B. Discrete channel C. T/R channel D. Transponder

Description : Combination of modulator, channel and detector. A. Transceiver B. Discrete channel C. T/R channel D. Transponder

Last Answer : B. Discrete channel

Cross modulation on a receiver is eliminated at the A. RF stage B. mixer stage C. IF stage D. detector stage

Description : Cross modulation on a receiver is eliminated at the A. RF stage B. mixer stage C. IF stage D. detector stage

Last Answer : D. detector stage

Give the classification of tuned amplifier

Description : Give the classification of tuned amplifier

Last Answer : (i) Small signal tuned amplifier *Single tuned *Double tuned *Stagger tuned (ii) Large signal tuned amplifier.

Give the classification of voltage regulators

Description : Give the classification of voltage regulators

Last Answer : *Series / Linear regulators  *Switching regulators.

Classification of clipper?

Description : Classification of clipper?

Last Answer : Practical clippers may be classified into two types: (a) Shunt Clippers, and (b) Series Clippers. The series configuration is defined as one where diode is in series with the load In a shunt ... and a resistive element, but it also employs an independent dc supply to introduce an additional shift.

List the broad classification of ADCs.

Description : List the broad classification of ADCs.

Last Answer : 1. Direct type ADC. 2. Integrating type ADC.

How is a quadrature detector changed when used for phase demodulation?

Description : How is a quadrature detector changed when used for phase demodulation?

Last Answer : The quadrature grid signal is excited by a reference from the transmitter.

Draw & explain operation of phase detector.

Description : Draw & explain operation of phase detector.

Last Answer : In phase detector, the op-Amp basically acts as a zero crossing detector. If a sine wave is applied at the i/p, we get square wave at the op-Amp o/p (at point ... to two channel of the CRO. The time duration between the pulses corresponding to voltages represent the phase between them. 

______ is the measurement of a unilateral antenna properties of directivity A. Phase angle B. Antenna gain C. Beamwidth D. Bandwidth

Description : ______ is the measurement of a unilateral antenna properties of directivity A. Phase angle B. Antenna gain C. Beamwidth D. Bandwidth

Last Answer : C. Beamwidth

If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Description : If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Last Answer : B. critical phased array

Which of the following is standardized as part of GSM phase 2+ that can offer theoretical data speeds of upto 115 kbit/s? A. EDGE B. GPRS C. WAP D. Bluetooth

Description : Which of the following is standardized as part of GSM phase 2+ that can offer theoretical data speeds of upto 115 kbit/s? A. EDGE B. GPRS C. WAP D. Bluetooth

Last Answer : B. GPRS

What distortion is not caused by transmission line characteristics? A. Phase distortion B. Pulse shape distortion C. Spacing bias distortion D. Amplitude distortion

Description : What distortion is not caused by transmission line characteristics? A. Phase distortion B. Pulse shape distortion C. Spacing bias distortion D. Amplitude distortion

Last Answer : C. Spacing bias distortion

What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Description : What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Last Answer : A. 0.25

What is a selective fading effect? A. A fading effect caused by small changes in beam heading at the receiving station. B. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station. C. A fading effect caused by large changes in the height of the ionosphere, as experienced at the receiving station D. A fading effect caused by time differences between the receiving and transmitting stations.

Description : What is a selective fading effect? A. A fading effect caused by small changes in beam heading at the receiving station. B. A fading effect caused by phase differences between radio wave ... station D. A fading effect caused by time differences between the receiving and transmitting stations.

Last Answer : B. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station.

What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Description : What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Last Answer : D. A frequency modulated continuous wave

What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Description : What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Last Answer : B. Direct sequence

The bending of radio waves passing over the top of a mountain range that disperses a weak portion of the signal behind the mountain is A. eddy-current phase effect B. knife-edge diffraction C. shadowing D. mirror refraction effect

Description : The bending of radio waves passing over the top of a mountain range that disperses a weak portion of the signal behind the mountain is A. eddy-current phase effect B. knife-edge diffraction C. shadowing D. mirror refraction effect

Last Answer : B. knife-edge diffraction

What is the major cause of selective fading? A. Small changes in the beam heading at the receiving station. B. Large changes in the height of the ionosphere, as experience at the receiving station. C. Time differences between the receiving and transmitting stations. D. Phase differences between radio wave components of the same transmission, as experienced at the receiving station.

Description : What is the major cause of selective fading? A. Small changes in the beam heading at the receiving station. B. Large changes in the height of the ionosphere, as experience at the ... Phase differences between radio wave components of the same transmission, as experienced at the receiving station.

Last Answer : D. Phase differences between radio wave components of the same transmission, as experienced at the receiving station.

Assume a frequency of 4 MHz, determine the phase shift offered by the line in the above problem. A. 108.5˚ B. 106.5˚ C. 115.5˚ D. 166.5˚

Description : Assume a frequency of 4 MHz, determine the phase shift offered by the line in the above problem. A. 108.5˚ B. 106.5˚ C. 115.5˚ D. 166.5˚

Last Answer : D. 166.5˚

One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Description : One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Last Answer : B. Phase control

What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Description : What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Last Answer : B. The combination of two signals to produce sum and difference frequencies.

The modulation technique used by GSM cellular system A. Phase shift keying B. Frequency shift keying C. Gaussian minimum shift keying D. QAM

Description : The modulation technique used by GSM cellular system A. Phase shift keying B. Frequency shift keying C. Gaussian minimum shift keying D. QAM

Last Answer : C. Gaussian minimum shift keying

Refers to an effect of selective fading. A. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station. B. A fading effect caused by small changes in beam heading at the receiving station. C. A fading effect caused by the time differences between the receiving and transmitting stations. D. A fading effect caused by large changes in the height of the ionosphere, as experienced at the receiving station.

Description : Refers to an effect of selective fading. A. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station. B. A fading ... caused by large changes in the height of the ionosphere, as experienced at the receiving station.

Last Answer : A. A fading effect caused by phase differences between radio wave components of the same transmission, as experienced at the receiving station.

A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Last Answer : D. 8.8 dB

What particular circuit that rids FM of noise? A. HPF B. Phase shifter C. Limiter D. LPF

Description : What particular circuit that rids FM of noise? A. HPF B. Phase shifter C. Limiter D. LPF

Last Answer : C. Limiter

What is the phase delay of an 800 Hz voice signal if the phase shift is 15 degrees? A. 1.25 µsec B. 52 µsec C. 83.33 µsec D. 26 µsec

Description : What is the phase delay of an 800 Hz voice signal if the phase shift is 15 degrees? A. 1.25 µsec B. 52 µsec C. 83.33 µsec D. 26 µsec

Last Answer : B. 52 µsec

How to produced 180° phase shift?

Description : How to produced 180° phase shift?

Last Answer : The most common way of achieving this kind of filter is using three identical cascaded resistor capacitor filters, which together produce a phase shift of zero at low frequencies, and 270 degrees at ... phase shift of 60 degrees and the whole filter circuit produces a phase shift of 180 degrees.

What is phase-shift oscillator?

Description : What is phase-shift oscillator?

Last Answer : A phase-shift oscillator is a simple electronic oscillator. It contains an inverting amplifier, and a feedback filter which 'shifts' the phase of the amplifier output by 180 degrees at the oscillation ... 180° at high frequencies, so that the phase shift at the desired oscillation frequency is 180°.

Both frequency and phase modulation utilize ________ modulation A. Phase B. AM and FM C. Digital D. Angle

Description : Both frequency and phase modulation utilize ________ modulation A. Phase B. AM and FM C. Digital D. Angle

Last Answer : D. Angle

What is the gain of four identically polarized antennas stacked one above the other and fed in phase? A. 3 dB over the gain of one antenna B. 10 dB over the gain of one antenna C. 4 dB over the gain of one antenna D. 6 dB over the gain of one antenna

Description : What is the gain of four identically polarized antennas stacked one above the other and fed in phase? A. 3 dB over the gain of one antenna B. 10 dB over the gain of one antenna C. 4 dB over the gain of one antenna D. 6 dB over the gain of one antenna

Last Answer : D. 6 dB over the gain of one antenna

What is the difference between phase and frequency modulation? A. Is purely theoretical because they are the same in practice B. Lies in poorer audio response of phase modulation C. Lies in the different definitions of the modulation index D. Is too great to make two systems compatible

Description : What is the difference between phase and frequency modulation? A. Is purely theoretical because they are the same in practice B. Lies in poorer audio response of phase modulation C. Lies in the different definitions of the modulation index D. Is too great to make two systems compatible

Last Answer : C. Lies in the different definitions of the modulation index

It consists of a number of dipoles of equal size, equally spaced along a straight line with all dipoles fed in the same phase from the same source. A. Log-periodic antenna B. Yagi antenna C. End-fire array D. Broadside array

Description : It consists of a number of dipoles of equal size, equally spaced along a straight line with all dipoles fed in the same phase from the same source. A. Log-periodic antenna B. Yagi antenna C. End-fire array D. Broadside array

Last Answer : D. Broadside array

In the phase shift method, How many circuits must be balanced? A. None of these B. 1 C. 4 D. 2

Description : In the phase shift method, How many circuits must be balanced? A. None of these B. 1 C. 4 D. 2

Last Answer : D. 2

ECE Board Exam March 1996 Passive crossover components cause some frequencies to be delayed with respect to the other frequencies at the crossover point. A. Phase shift B. Phase correction C. Phase-error correction D. Time alignment

Description : ECE Board Exam March 1996 Passive crossover components cause some frequencies to be delayed with respect to the other frequencies at the crossover point. A. Phase shift B. Phase correction C. Phase-error correction D. Time alignment

Last Answer : A. Phase shift

For perfect lock, what should be the phase relation between the incoming signal and VCO output signal?

Description : For perfect lock, what should be the phase relation between the incoming signal and VCO output signal?

Last Answer : The VCO output should be 90 degrees out of phase with respect to the input signal.

State classification of Phase controlled rectifiers.

Description : State classification of Phase controlled rectifiers.

Last Answer : Classification of phase controlled rectifiers:

State the classification of single phase induction motors.

Description : State the classification of single phase induction motors.

Last Answer : Types of single phase induction motors: 1. Split phase induction motor. 2. Capacitor start inductor motor. 3. Capacitor start capacitor run induction motor. 4. Permanent split capacitor motor. 5. Shaded pole induction motor. 

The parasitic element of an antenna system will A. decrease its directivity B. increase its directivity C. give the antenna unidirectional properties D. both B and C

Description : The parasitic element of an antenna system will A. decrease its directivity B. increase its directivity C. give the antenna unidirectional properties D. both B and C

Last Answer : D. both B and C

Batteries are used to power all satellite subsystems A. at all times B. only during emergencies C. during eclipse periods D. to give the solar arrays a rest

Description : Batteries are used to power all satellite subsystems A. at all times B. only during emergencies C. during eclipse periods D. to give the solar arrays a rest

Last Answer : C. during eclipse periods