Description : In television broadcasting vivid strong colors are often referred as _______. A. Saturation B. Hue C. Chrominance D. Luminance
Last Answer : A. Saturation
Description : What controls the contrast of a television cathode ray picture? A. AFC B. video stage gain C. Audio gain control D. CRT bias
Last Answer : B. video stage gain
Description : Which of the following feature is used to revert the original picture? (a) Recolor (b) Contrast (c) Brightness (d) Reset picture -Technology
Last Answer : (d) Reset picture feature of Picture Tools Format is used to revert the original picture.
Description : Luminance efficiency is minimum for a a. Fluorescent tube b. High wattage light bulb c. Mercury vapor lamp d. Low wattage light bulb
Last Answer : d. Low wattage light bulb
Description : Where is the brightness control located in a TV? A. The audio section B. The video section C. The grid-cathode circuit D. The front panel
Last Answer : A. The audio section
Description : The following are true about the contrast sensitivity: a. Pelli-Robson chart tests the contrast sensitivity b. is a measure of the ratio of brightness to darkness c. a contrast of 1 means that there is no contrast d. is highest at middle range frequencies
Last Answer : is highest at middle range frequencies
Description : In regard to colour, what does Chroma stand for, A. Degree of saturation of hue B. Brightness C. Value D. Contrast
Last Answer : A. Degree of saturation of hue
Description : Refers to the first symbol in an emission designation with an amplitude modulated main carrier represented by letter H. A. Single sideband suppressed carrier B. Double sideband full carrier C. Independent sideband D. Double sideband
Last Answer : B. Double sideband full carrier
Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere
Last Answer : C. In the receiver front end
Description : What determines the ability of radar to determine the bearing to a target? A. Speed of light B. Speed of target C. Antenna directivity D. Frequency of signal
Last Answer : C. Antenna directivity
Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere
Description : A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz
Last Answer : C. 999.8 kHz, 1000 kHz, and 1000.2 kHz
Description : What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave
Last Answer : D. A frequency modulated continuous wave
Description : One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control
Last Answer : B. Phase control
Description : What is the first symbol of a radio signal transmission having an amplitude modulated signal carrier, double side band? A. C B. B C. H D. A
Last Answer : D. A
Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal
Last Answer : A. Interference to adjacent channel
Description : A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude
Last Answer : A. Constant peak amplitude
Description : If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt
Last Answer : A. 1.14 volts
Description : Does a greater contrast ratio equate to better picture quality?
Last Answer : Yes, it will make the picture much sharper.
Description : The ENERGY associated with a photon depends upon the photon's: w) velocity x) frequency y) amplitude z) the brightness of the source from which it comes
Last Answer : ANSWER: X -- FREQUENCY
Description : What significant element of sound refers to its characteristic tonal quality? A. Pitch B. Tempo C. Rhythm D. Timbre
Last Answer : D. Timbre
Description : ……… option is used to adjust the brightness of the picture. -Technology
Last Answer : Brightnessoption is used to adjust the brightness of the picture.
Description : Technical study which deals with production, transport and delivery of a quality signal from source to destination. A. Transmission system engineering B. Communication system engineering C. Telephony engineering D. Telegraphic engineering
Last Answer : A. Transmission system engineering
Description : Digital transmission provides a higher level of signal quality than analog transmission because A. repeaters regenerate digital pulses and remove distorstion B. digital signals are easier to sample than ... and cannot easily be distorted D. analog signals are continuous and not easily distorted.
Last Answer : A. repeaters regenerate digital pulses and remove distorstion
Description : Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses
Last Answer : A. RF carrier
Description : Pattern ERG (PERG): a. tests the function of the ganglion cells b. uses a checkered board pattern that changes in luminance c. gives the same information as visual evoked response (VER) d. is abnormal in glaucoma
Last Answer : is abnormal in glaucoma
Description : Luminance efficiency is minimum for a ∙ a. Fluorescent tube ∙ b. High wattage light bulb ∙ c. Mercury vapor lamp ∙ d. Low wattage light bulb
Description : Which among the following determines the pitch of a sound? (1) Amplitude (2) Frequency (3) Loudness (4) Wavelength
Last Answer : (2) Frequency Explanation: The pitch of a sound is determined by the frequency of vibration of the sound waves So higher the frequency the higher is the pitch.
Description : Which of the answers listed below best completes the statement: The rate at which any part of a wave travels from one place to another determines the wave's: w) propagation velocity x) period y) amplitude z) frequency
Last Answer : ANSWER: W -- PROPAGATION VELOCITY
Description : What determines antenna polarization? A. The frequency of the radiated wave B. The direction of the radiated wave C. The direction of the magnetic field vector D. The direction of the electric field vector
Last Answer : D. The direction of the electric field vector
Description : Which of the following determines the acoustic behavior of gases? A. Density B. Pressure C. Temperature D. All of the choices
Last Answer : D. All of the choices
Description : What determines the velocity factor in a transmission line? A. The termination impedance B. The line length C. Dielectrics in the line D. The center conductor resistivity
Last Answer : C. Dielectrics in the line
Description : Which of the following determines the characteristics of a transmission line? A. Inductance B. Capacitance C. Physical dimension D. Length
Last Answer : C. Physical dimension
Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley
Last Answer : B. MOPA
Description : What determines the velocity factor in transmission line? A. The center conductor resistivity B. Dielectrics in the line C. The termination impedance D. The line length
Last Answer : B. Dielectrics in the line
Description : Which determines the number of sideband components of FM? A. Modulation frequency B. Modulation index C. Carrier frequency D. All of these
Last Answer : B. Modulation index
Description : Noise consisting of irregular pulses of short duration and relatively high amplitude, A. Quantizing noise B. Tone interference C. Impulse noise D. Cross talk
Last Answer : C. Impulse noise
Last Answer : A. Quantizing noise
Description : A 1000W carrier is amplitude modulated to a depth of 85%. Calculate the total power of the modulated wave? A. 1361.25 W B. 680.62 W C. 1425 W D. 712.5 W
Last Answer : A. 1361.25 W
Description : What distortion is not caused by transmission line characteristics? A. Phase distortion B. Pulse shape distortion C. Spacing bias distortion D. Amplitude distortion
Last Answer : C. Spacing bias distortion
Description : In modulation technique, which of the following is referred to audible pitch? A. Width B. Frequency C. Harmonic D. Amplitude
Last Answer : B. Frequency
Description : This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation
Last Answer : C. Dynamic instability
Description : In amplitude modulation technique the unmodulated carrier is referred to as having ______. A. 100% modulation B. 0% modulation C. 50% modulated D. Over modulated
Last Answer : B. 0% modulation
Description : What is the period of a wave? A. The number of degrees in tone cycle B. The number of zero crossing in one cycle C. The amplitude of the wave D. The time required to complete one cycle
Last Answer : D. The time required to complete one cycle
Description : Which of the following systems is not used in radio detection and ranging? A. Frequency shift B. Frequency modulation C. Pulse radar D. Amplitude modulation
Last Answer : D. Amplitude modulation
Description : Used for time division multiplexing. A. Frequency modulation B. Pulsed modulation C. SSB D. Amplitude modulation
Last Answer : B. Pulsed modulation
Description : A method of expressing the amplitude of complex non-periodic signals such as speech. A. Frequency B. Wavelength C. Volume D. Pitch
Last Answer : C. Volume
Description : The series of periodically recurrent pulses is modulated in amplitude by the corresponding instantaneous samples. A. PFM B. PWM C. PDM D. PAM
Last Answer : D. PAM
Description : What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion
Last Answer : D. To protect small signals in PCM from quantizing distortion
Description : Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire
Last Answer : C. Varying of some parameters of a carrier such as its amplitude to transmit information