Determine the conductance of a two-wire open line with the following parameters: D = 4 in., d = 0.1 in. and ρ = 2.6x108 Ω-m. A. 2.76x10-9 S/m B. 2.76x10-6 S/m C. 2.76x10-12 S/m D. 2.76x10-3 S/m

Determine the conductance of a two-wire open line with the following parameters: D = 4 in.,
d = 0.1 in. and ρ = 2.6x108 Ω-m.
A. 2.76x10-9 S/m
B. 2.76x10-6 S/m
C. 2.76x10-12 S/m
D. 2.76x10-3 S/m
by

1 Answer

Answer :

A. 2.76x10-9 S/m
by

Related questions

Determine the standing wave ratio of a 300-Ω line whose load is 400+j150 Ω. A. 3.55 B. 1.67 C. 5.53 D. 3.35

Description : Determine the standing wave ratio of a 300-Ω line whose load is 400+j150 Ω. A. 3.55 B. 1.67 C. 5.53 D. 3.35

Last Answer : B. 1.67

What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω

Description : What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω

Last Answer : D. 75 Ω

What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω

Description : What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω

Last Answer : A. 100Ω

What is the typical velocity factor of open-wire line? A. 0.9 B. 0.8 C. 0.5 D. 0.7

Description : What is the typical velocity factor of open-wire line? A. 0.9 B. 0.8 C. 0.5 D. 0.7

Last Answer : A. 0.9

The parameters of Transmission line are R = 50 Ω/ km, L= 1mH/km ,C = 0.1µf/km, G = 2µV/km. calculate characteristic impedance.

Description : The parameters of Transmission line are R = 50 Ω/ km, L= 1mH/km ,C = 0.1µf/km, G = 2µV/km. calculate characteristic impedance.

Last Answer : The parameters of Transmission line are R = 50 Ω/ km, L= 1mH/km ,C = 0.1µf/km, G = 2µV/km. calculate characteristic impedance.

Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Description : Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Last Answer : C. Varying of some parameters of a carrier such as its amplitude to transmit information

In transmission line, which of the following is the first step in the procedure of using stub matching? A. Calculate stub susceptance. B. Calculate load admittance C. Connect stub to load D. Transform conductance to resistance

Description : In transmission line, which of the following is the first step in the procedure of using stub matching? A. Calculate stub susceptance. B. Calculate load admittance C. Connect stub to load D. Transform conductance to resistance

Last Answer : B. Calculate load admittance

___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Description : ___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Last Answer : A. Psophometer

What line has a typical velocity factor of about 0.8? A. Shielded pair B. Flexible coaxial C. Twin-lead D. Open-wire line

Description : What line has a typical velocity factor of about 0.8? A. Shielded pair B. Flexible coaxial C. Twin-lead D. Open-wire line

Last Answer : C. Twin-lead

The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, respectively. Calculate the equivalent input-noise resistance of this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

What is the typical separation between the two conductors in a parallel wire line? A. 0.001 to 0.01 m B. 200 to 500 mm C. 0.635 to 15.24 cm D. 2.5 to 5 in.

Description : What is the typical separation between the two conductors in a parallel wire line? A. 0.001 to 0.01 m B. 200 to 500 mm C. 0.635 to 15.24 cm D. 2.5 to 5 in.

Last Answer : C. 0.635 to 15.24 cm

A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Description : A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Last Answer : D. 112 Ω

What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150Ω D. 2 Ω

Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω

Last Answer : C. 150 Ω

What quarterwave transformer will match a 100Ω line to an antenna whose value is 175Ω? A. 132.29 Ω B. 150 Ω C. 16.58 Ω D. 137.5 Ω

Description : What quarterwave transformer will match a 100Ω line to an antenna whose value is 175Ω? A. 132.29 Ω B. 150 Ω C. 16.58 Ω D. 137.5 Ω

Last Answer : A. 132.29 Ω

Which of the following parameters is not a primary parameter? a) Resistance b) Attenuation constant c) Capacitance d) Conductance

Description : Which of the following parameters is not a primary parameter? a) Resistance b) Attenuation constant c) Capacitance d) Conductance

Last Answer : Ans: B

Which of the following is considered the most frequently used transmission line? A. Two-wire open line B. Twin lead C. Rigid coaxial line D. Flexible coaxial line

Description : Which of the following is considered the most frequently used transmission line? A. Two-wire open line B. Twin lead C. Rigid coaxial line D. Flexible coaxial line

Last Answer : D. Flexible coaxial line

A transmission line consisting of two conductors that have equal resistance per unit length. A. Unbalanced line B. Open-wire line C. Balanced line D. Coaxial line

Description : A transmission line consisting of two conductors that have equal resistance per unit length. A. Unbalanced line B. Open-wire line C. Balanced line D. Coaxial line

Last Answer : C. Balanced line

A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K

The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ

Description : The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ

Last Answer : (A) 3.6 AVS.ρ

A vibrating machine of 100 kg is mounted on a rubber pad which has stiffness of 500 N/m. Determine force transmitted to the foundation if the unbalanced force 500 N acts on it. The frequency ratio (ω/ω n ) is 1.5 and ξ = 0.5 A. 461.62 N B. 400.23 N C. 450 N D. Insufficient data

Description : A vibrating machine of 100 kg is mounted on a rubber pad which has stiffness of 500 N/m. Determine force transmitted to the foundation if the unbalanced force 500 N acts on it. The frequency ratio (ω/ω n ) is 1.5 and ξ = 0.5 A. 461.62 N B. 400.23 N C. 450 N D. Insufficient data

Last Answer : A. 461.62 N

A transmitted signal 5 meters in wavelength is received by an antenna coil having a 50-Ω resistance and a 0.01 H inductance. What is the capacitance of the tuner shunting the antenna coil at this point? A. 0.704 fF B. 0.704 μF C. 0.704 nF D. 0.704 mF

Description : A transmitted signal 5 meters in wavelength is received by an antenna coil having a 50-Ω resistance and a 0.01 H inductance. What is the capacitance of the tuner shunting the antenna coil at this point? A. 0.704 fF B. 0.704 μF C. 0.704 nF D. 0.704 mF

Last Answer : A. 0.704 fF

What do you call the electrical conduction in a photosensitive material which is not exposed to radiation? A. Dark conductance B. Pure conductance C. Black out D. Super conductance

Description : What do you call the electrical conduction in a photosensitive material which is not exposed to radiation? A. Dark conductance B. Pure conductance C. Black out D. Super conductance

Last Answer : A. Dark conductance

The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω

Description : The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω

Last Answer : B. 300 Ω

Most mobile satellite array uses ___________ in transforming 50 to 150 Ω impedance. A. stub B. balun C. quarter-wavelength transformer D. microstrip tapers.

Description : Most mobile satellite array uses ___________ in transforming 50 to 150 Ω impedance. A. stub B. balun C. quarter-wavelength transformer D. microstrip tapers.

Last Answer : C. quarter-wavelength transformer

What is the end impedance of a half-wave dipole? A. 73 Ω B. 72 Ω C. 250 Ω D. 2500 Ω

Description : What is the end impedance of a half-wave dipole? A. 73 Ω B. 72 Ω C. 250 Ω D. 2500 Ω

Last Answer : D. 2500 Ω

What is the impedance in ohms of a transformer marked for 25V, 4W, when the secondary is correctly loaded? A. 150 Ω B. 156 Ω C. 160 Ω D. 165 Ω

Description : What is the impedance in ohms of a transformer marked for 25V, 4W, when the secondary is correctly loaded? A. 150 Ω B. 156 Ω C. 160 Ω D. 165 Ω

Last Answer : B. 156 Ω

What is the characteristic impedance of a two-wire line with the following data: diameter = 0.023in., spacing =0.5 in., insulation = PE.? A. 300Ω B. 250Ω C. 305Ω D. 301Ω

Description : What is the characteristic impedance of a two-wire line with the following data: diameter = 0.023in., spacing =0.5 in., insulation = PE.? A. 300Ω B. 250Ω C. 305Ω D. 301Ω

Last Answer : D. 301Ω

The specific surface of spherical particles is given by (where D and ρ are diameter and density of particle). (A) 6/D.ρ(B) 2/D.ρ (C) 4/D.ρ (D) 12/D.ρ

Description : The specific surface of spherical particles is given by (where D and ρ are diameter and density of particle). (A) 6/D.ρ (B) 2/D.ρ (C) 4/D.ρ (D) 12/D.ρ

Last Answer : (A) 6/D.ρ

Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls in rotation per second (rps) D = diameter of rolls, m). (A) 3.6 V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ

Description : Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls ... V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ

Last Answer : (A) 3.6 V.W.Dr.ρ

Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Description : Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Last Answer : B. 6 dB

A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is

Description : A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is A) Manganin wire of 20 m Ω B) Constantan wire of 20 m Ω C) Manganin wire of 25 m Ω D) Constantan wire of 25 m Ω

Last Answer : A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is Manganin wire of 25 m Ω

How do I work out the area or length of a wire when I only know the resistance/conductance and the length/area?

Description : How do I work out the area or length of a wire when I only know the resistance/conductance and the length/area?

Last Answer : if cunductance = conductivity x area/length then length = conductivity / conductance x Area i think, if the equation is transposed correctly, it’s been a while since school maths. better check that one though.

How to work out the conductance of a wire?

Description : How to work out the conductance of a wire?

Last Answer : I know ½000 is the right answer but I want it to say 0.0005

Safety fuse wire used in domestic electrical appliances is made of metal of low (1) Resistance (2) Melting point (3) Specific gravity (4) Conductance

Description : Safety fuse wire used in domestic electrical appliances is made of metal of low (1) Resistance (2) Melting point (3) Specific gravity (4) Conductance

Last Answer : (2) Melting point Explanation: The fuse wire is based on the Joules law of heating which says that when the electric current is allowed to pass through a conductor, the conductor heats up and is ... . For this purpose the material used as fuse wire should have high resistance and low melting point.

A wire having very high value of conductance is said to be a. very good conductor b. moderately good conductor c. an insulator d. None

Description : A wire having very high value of conductance is said to be a. very good conductor b. moderately good conductor c. an insulator d. None

Last Answer : a. very good conductor

Safety fuse wire used in domestic electrical appliances is made of metal of low (1) Resistance (2) Melting point (3) Specific gravity (4) Conductance

Description : Safety fuse wire used in domestic electrical appliances is made of metal of low (1) Resistance (2) Melting point (3) Specific gravity (4) Conductance

Last Answer : Melting point

What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Description : What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Last Answer : A. 0.25

A properly matched transmission line has a loss of 1.5 dB/100m. if 10 W is supplied to one end of the line, how many watts reach the load, 27 m away? A. 10 W B. 7.2 W C. 9.9 W D. 9.1 W

Description : A properly matched transmission line has a loss of 1.5 dB/100m. if 10 W is supplied to one end of the line, how many watts reach the load, 27 m away? A. 10 W B. 7.2 W C. 9.9 W D. 9.1 W

Last Answer : D. 9.1 W

Calculate damping ratio if mass = 200Kg, ω = 20rad/s and damping coefficient = 800 N/m/s A. 0.03 B. 0.04 C. 0.05 D. 0.06

Description : Calculate damping ratio if mass = 200Kg, ω = 20rad/s and damping coefficient = 800 N/m/s A. 0.03 B. 0.04 C. 0.05 D. 0.06

Last Answer : A. 0.03

Which among the following is the fundamental equation of S.H.M.? A. x + (k / m) x =0 B. x + ω 2 x =0 C. x + (k/ m) 2 x =0 D. x 2 + ωx 2 =0

Description : Which among the following is the fundamental equation of S.H.M.? A. x + (k / m) x =0 B. x + ω 2 x =0 C. x + (k/ m) 2 x =0 D. x 2 + ωx 2 =0

Last Answer : B. x + ω 2 x =0

Which among the following is the fundamental equation of S.H.M.? A) x + (k / m) x =0 B) x + ω 2 x =0 C) x + (k/ m) 2 x =0 D) x 2 + ωx 2 =0

Description : Which among the following is the fundamental equation of S.H.M.? A) x + (k / m) x =0 B) x + ω 2 x =0 C) x + (k/ m) 2 x =0 D) x 2 + ωx 2 =0

Last Answer : B) x + ω 2 x =0

Which among the following is the fundamental equation of S.H.M.? a. x+(k/m)x=0 b. x+ω 2 x=0 c. x+(k/m) 2 x=0 d. x 2 + ωx 2 =0

Description : Which among the following is the fundamental equation of S.H.M.? a. x+(k/m)x=0 b. x+ω 2 x=0 c. x+(k/m) 2 x=0 d. x 2 + ωx 2 =0

Last Answer : d. x 2 + ωx 2 =0

Calculate damping ratio from the following data: mass = 200Kg ω = 20rad/s damping coefficient = 1000 N/m/s a) 0.03 b) 0.04 c) 0.05 d) 0.06

Description : Calculate damping ratio from the following data: mass = 200Kg ω = 20rad/s damping coefficient = 1000 N/m/s a) 0.03 b) 0.04 c) 0.05 d) 0.06

Last Answer : b) 0.04

Calculate damping ratio from the following data: mass = 200Kg ω = 20rad/s damping coefficient = 800 N/m/s a) 0.03 b) 0.04 c) 0.05 d) 0.06

Description : Calculate damping ratio from the following data: mass = 200Kg ω = 20rad/s damping coefficient = 800 N/m/s a) 0.03 b) 0.04 c) 0.05 d) 0.06

Last Answer : a) 0.03

A system weighing 2kN. Determine the force that accelerate if to 12 m/s^2. a. vertically upward when g = 9.7 m/s^2  A. 4474.23 N  B.5484.23 N  C.4495.23 N  D.5488.23 N Formula: F = m/k (a +g)

Description : A system weighing 2kN. Determine the force that accelerate if to 12 m/s^2. a. vertically upward when g = 9.7 m/s^2  A. 4474.23 N  B.5484.23 N  C.4495.23 N  D.5488.23 N Formula: F = m/k (a +g)

Last Answer : 4474.23 N

What is the optimum reverberation time at 500 to 1000 Hz of an auditorium? A. 0.9 to 1.1 s B. 1.4 to 1.6 s C. 1.5 to 1.6 s D. 1.6 to 1.8 s

Description : What is the optimum reverberation time at 500 to 1000 Hz of an auditorium? A. 0.9 to 1.1 s B. 1.4 to 1.6 s C. 1.5 to 1.6 s D. 1.6 to 1.8 s

Last Answer : D. 1.6 to 1.8 s

Which of the following is not a bounded medium? A. Coaxial line B. Two-wire line C. Waveguide D. Free space

Description : Which of the following is not a bounded medium? A. Coaxial line B. Two-wire line C. Waveguide D. Free space

Last Answer : D. Free space

What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Description : What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Last Answer : A. Twisted pair

What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Description : What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Last Answer : B. A specially configured coaxial transmission line