A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz

A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire
that is hanged between two towers. What is the frequency of its third harmonic?
A. 727 kHz
B. 6546 kHz
C. 436 kHz
D. 6.546 kHz
by

1 Answer

Answer :

B. 6546 kHz
by

Related questions

In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Description : In order to get maximum radiation to all surrounding points in the horizontal plane, the antenna used is a A. vertical loop B. vertical quarter-wavelength rod C. array which includes parasitic elements D. a horizontal Hertz dipole

Last Answer : B. vertical quarter-wavelength rod

Which of the following antennas receive signals in the horizontal plane equality well from all directions? A. Horizontal Hertz antenna B. Vertical loop antenna C. Vertical Yagi antenna D. A vertical antenna which is a quarter-wavelength long

Description : Which of the following antennas receive signals in the horizontal plane equality well from all directions? A. Horizontal Hertz antenna B. Vertical loop antenna C. Vertical Yagi antenna D. A vertical antenna which is a quarter-wavelength long

Last Answer : D. A vertical antenna which is a quarter-wavelength long

The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Description : The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Last Answer : C. increase the antenna’s power gain

If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its resonant frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Description : If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its ... frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Last Answer : C. its resonant frequency will be increased

How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Description : How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Last Answer : D. By connecting an inductor in series with the antenna

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

How does the gain of a parabolic dish type antenna change when the operating frequency is doubled? A. Gain does not change B. Gain is multiplied by 0.707 C. Gain increases 6 dB D. Gain increases 3 dB

Description : How does the gain of a parabolic dish type antenna change when the operating frequency is doubled? A. Gain does not change B. Gain is multiplied by 0.707 C. Gain increases 6 dB D. Gain increases 3 dB

Last Answer : C. Gain increases 6 dB

Which antenna does not use the ground? A. Marconi B. Yagi C. Hertz D. Rhombic

Description : Which antenna does not use the ground? A. Marconi B. Yagi C. Hertz D. Rhombic

Last Answer : B. Yagi

Which antenna is not grounded at one end? A. Hertz B. Marconi C. Dipole D. Whip

Description : Which antenna is not grounded at one end? A. Hertz B. Marconi C. Dipole D. Whip

Last Answer : C. Dipole

Which of the following antennas require good grounding? A. Yagi antenna B. Hertz antenna C. Marconi antenna D. Isotropic antenna

Description : Which of the following antennas require good grounding? A. Yagi antenna B. Hertz antenna C. Marconi antenna D. Isotropic antenna

Last Answer : C. Marconi antenna

This is a flexible vertical rod antenna commonly used on mobiles. A. Marconi B. Hertz C. Whip D. Ground plane

Description : This is a flexible vertical rod antenna commonly used on mobiles. A. Marconi B. Hertz C. Whip D. Ground plane

Last Answer : C. Whip

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

Which is properly terminated antenna? A. Rhombic B. Hertz C. Marconi D. Dipole

Description : Which is properly terminated antenna? A. Rhombic B. Hertz C. Marconi D. Dipole

Last Answer : A. Rhombic

ECE Board Exam March 1996 A type of an underground antenna is a/an __________ antenna. A. Hertz B. isotropic C. parabolic D. Marconi

Description : ECE Board Exam March 1996 A type of an underground antenna is a/an __________ antenna. A. Hertz B. isotropic C. parabolic D. Marconi

Last Answer : A. Hertz

A recorder’s harmonic-distortion specification reads 2% third harmonic of a 100-kHz signal at 60 ips. What does this mean?

Description : A recorder’s harmonic-distortion specification reads 2% third harmonic of a 100-kHz signal at 60 ips. What does this mean?

Last Answer : The recorder has 2% third-harmonic distortion of a 100-kHz signal at 60 ips.

Harmonic suppressor connected to an antenna. A. Low-pass filter B. High-pass filter C. M-derived filter D. Constant-K

Description : Harmonic suppressor connected to an antenna. A. Low-pass filter B. High-pass filter C. M-derived filter D. Constant-K

Last Answer : A. Low-pass filter

What is the seventh harmonic of a 100 MHz quarter wavelength antenna? A. 14.28 MHz B. 107 MHz C. 149 MHz D. 700 MHz

Description : What is the seventh harmonic of a 100 MHz quarter wavelength antenna? A. 14.28 MHz B. 107 MHz C. 149 MHz D. 700 MHz

Last Answer : D. 700 MHz

Harmonic suppressor connected to an antenna. A. High pass filter B. Low pass filter C. Tank circuit D. M-derived filter

Description : Harmonic suppressor connected to an antenna. A. High pass filter B. Low pass filter C. Tank circuit D. M-derived filter

Last Answer : B. Low pass filter

The length of a Marconi antenna to operate with 985 kHz is ______. A. 200 ft B. 500 ft C. 250 ft D. 999 ft

Description : The length of a Marconi antenna to operate with 985 kHz is ______. A. 200 ft B. 500 ft C. 250 ft D. 999 ft

Last Answer : C. 250 ft

Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it is assumed that each sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Description : Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it ... sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Last Answer : (C) 128 kbps

When measuring harmonic distortion, you set the signal generator to input a 15-kHz test signal. To what frequency should you set the wave analyzer?

Description : When measuring harmonic distortion, you set the signal generator to input a 15-kHz test signal. To what frequency should you set the wave analyzer?

Last Answer : 45 kHz.

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66

Description : What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66

Last Answer : D. 1.66

If frequency range of 401.000MHz to 401.050MHz has to be channelized at 12.5 kHz between channel, what is the center of its first channel from the lower limit? A. 401.125MHz B. 401.00625MHz C. 401.025MHz D. 401.0125MHz

Description : If frequency range of 401.000MHz to 401.050MHz has to be channelized at 12.5 kHz between channel, what is the center of its first channel from the lower limit? A. 401.125MHz B. 401.00625MHz C. 401.025MHz D. 401.0125MHz

Last Answer : B. 401.00625MHz

In modulation technique, which of the following is referred to audible pitch? A. Width B. Frequency C. Harmonic D. Amplitude

Description : In modulation technique, which of the following is referred to audible pitch? A. Width B. Frequency C. Harmonic D. Amplitude

Last Answer : B. Frequency

The lowest frequency produced by an instrument. A. Harmonic B. Fundamental C. Midrange D. 0 Hz

Description : The lowest frequency produced by an instrument. A. Harmonic B. Fundamental C. Midrange D. 0 Hz

Last Answer : B. Fundamental

Lowest frequency produced by a musical instrument. A. Fundamental B. Midrange C. Period D. Harmonic

Description : Lowest frequency produced by a musical instrument. A. Fundamental B. Midrange C. Period D. Harmonic

Last Answer : A. Fundamental

Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Description : Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Last Answer : C. 15 to 160 MHz

What is the approximate bandwidth of an FM system with 10 kHz of modulating frequency and a 150 kHz of frequency deviation? A. 300 kHz B. 320 kHz C. 150 kHz D. 200 kHz

Description : What is the approximate bandwidth of an FM system with 10 kHz of modulating frequency and a 150 kHz of frequency deviation? A. 300 kHz B. 320 kHz C. 150 kHz D. 200 kHz

Last Answer : B. 320 kHz

In acoustics, if the volume of the room is 200 m3 then at what frequency the coefficient of absorption is measured? A. 120 kHz B. 120 Hz C. 100 Hz D. 150 Hz

Description : In acoustics, if the volume of the room is 200 m3 then at what frequency the coefficient of absorption is measured? A. 120 kHz B. 120 Hz C. 100 Hz D. 150 Hz

Last Answer : B. 120 Hz

What is the carrier frequency of supergroup 10? A. 2724 kHz B. 2356 kHz C. 2108 kHz D. 3100 kHz

Description : What is the carrier frequency of supergroup 10? A. 2724 kHz B. 2356 kHz C. 2108 kHz D. 3100 kHz

Last Answer : D. 3100 kHz

A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz

Description : A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz

Last Answer : B. 660 kHz

What is the typical frequency used for communicating to submerged submarines? A. 100 Hz B. 500 Hz C. 4 kHz D. 200 Hz

Description : What is the typical frequency used for communicating to submerged submarines? A. 100 Hz B. 500 Hz C. 4 kHz D. 200 Hz

Last Answer : A. 100 Hz

Tropospheric scatter is a method of sky wave propagation for which of the following frequency bands? A. 300 kHz to 3 MHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 300 MHz to 3 GHz

Description : Tropospheric scatter is a method of sky wave propagation for which of the following frequency bands? A. 300 kHz to 3 MHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 300 MHz to 3 GHz

Last Answer : D. 300 MHz to 3 GHz

Which of the following frequency bands is best suited for sky wave propagation? A. 30 to 300 kHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 3 GHz to 30 GHz

Description : Which of the following frequency bands is best suited for sky wave propagation? A. 30 to 300 kHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 3 GHz to 30 GHz

Last Answer : B. 3 MHz to 30 MHz

Which of the following frequency bands is best suited for ground wave propagation? A. 30 to 300 kHz B. 300 kHz to 3 MHzC. 3 MHz to 30 MHz D. 30 MHz to 300 MHz

Description : Which of the following frequency bands is best suited for ground wave propagation? A. 30 to 300 kHz B. 300 kHz to 3 MHz C. 3 MHz to 30 MHz D. 30 MHz to 300 MHz

Last Answer : A. 30 to 300 kHz

What frequency is 10 octaves above 30 Hz? A. 30.72 kHz B. 30 kHz C. 300 Hz D. 307.2 kHz

Description : What frequency is 10 octaves above 30 Hz? A. 30.72 kHz B. 30 kHz C. 300 Hz D. 307.2 kHz

Last Answer : A. 30.72 kHz

What is the frequency of a 2-cm sound wave in sea water at 25˚C? A. 76 kHz B. 76 Hz C. 76 MHz D. 76 mHz

Description : What is the frequency of a 2-cm sound wave in sea water at 25˚C? A. 76 kHz B. 76 Hz C. 76 MHz D. 76 mHz

Last Answer : A. 76 kHz

Assuming a UHF frequency range of 405.0125 MHz to 405.0875 MHz at 25 kHz channeling plan, how many channels can you produce? A. 2.5 ch. B. 2 ch. C. 4 ch. D. 3 ch.

Description : Assuming a UHF frequency range of 405.0125 MHz to 405.0875 MHz at 25 kHz channeling plan, how many channels can you produce? A. 2.5 ch. B. 2 ch. C. 4 ch. D. 3 ch.

Last Answer : D. 3 ch.

Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Description : Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Last Answer : C. 405.050 MHz

Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Description : Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Last Answer : B. 401.0125 MHz

The extremely high frequency (EHF) band is in the radio spectrum range of _______. A. 30 to 300 kHz B. 30 to 300 GHz C. 3 to 30 MHz D. 3 to 30 GHz

Description : The extremely high frequency (EHF) band is in the radio spectrum range of _______. A. 30 to 300 kHz B. 30 to 300 GHz C. 3 to 30 MHz D. 3 to 30 GHz

Last Answer : B. 30 to 300 GHz

For a sample rate of 40 kHz, determine the maximum analog input frequency A. 30 kHz B. 40 kHz C. 20 kHz D. 10 kHz

Description : For a sample rate of 40 kHz, determine the maximum analog input frequency A. 30 kHz B. 40 kHz C. 20 kHz D. 10 kHz

Last Answer : C. 20 kHz

What is the local oscillator frequency range commercial AM broadcast if it is equal to 455 KHz. A. 540 to 1600 KHz B. 0 to 1600 KHz C. 995 to 2055 KHz D. 0 to 455 KHz

Description : What is the local oscillator frequency range commercial AM broadcast if it is equal to 455 KHz. A. 540 to 1600 KHz B. 0 to 1600 KHz C. 995 to 2055 KHz D. 0 to 455 KHz

Last Answer : C. 995 to 2055 KHz

Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz

Description : Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz

Last Answer : B. 15 to 160 Mhz

What is the baseband frequency of standard FDM basic supergroup? A. 312 to 552 kHz B. 300 to 600 kHz C. 60 to 2540 kHz D. 60 to 108 kHz

Description : What is the baseband frequency of standard FDM basic supergroup? A. 312 to 552 kHz B. 300 to 600 kHz C. 60 to 2540 kHz D. 60 to 108 kHz

Last Answer : A. 312 to 552 kHz

The frequency spectrum of the stereophonic FM signal. A. 67 kHz B. 59.5 to 74.5 kHz C. 19 to 38 kHz D. 30 to 53 kHz

Description : The frequency spectrum of the stereophonic FM signal. A. 67 kHz B. 59.5 to 74.5 kHz C. 19 to 38 kHz D. 30 to 53 kHz

Last Answer : D. 30 to 53 kHz

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the same as that of the intermediate frequency C. Generates a 1kHz note for Morse code reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

The latest government regulation in the telecommunication which provides policy for the provision of local exchange carrier service. A. E.O. 546 B. E.O. 109 C. Act 3948 D. E.O. 59

Description : The latest government regulation in the telecommunication which provides policy for the provision of local exchange carrier service. A. E.O. 546 B. E.O. 109 C. Act 3948 D. E.O. 59

Last Answer : B. E.O. 109