A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz

A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on
a frequency of 1570 kHz. The receiver is tuned to
A. 1115 kHz
B. 660 kHz
C. 2025 kHz
D. 910 kHz
by

1 Answer

Answer :

B. 660 kHz
by

Related questions

An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz

Description : An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz

Last Answer : D. 99.7 MHz

A super heterodyne AM receiver is tuned to a station operating at 1200 KHz .Find local oscillator frequency and image frequency.

Description : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz .Find local oscillator frequency and image frequency.

Last Answer : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz Intermediate frequency is 455KHz. IF frequency=f0-fs Local oscillator frequency is f0=IF +fs=455K+1200K=1655kHz The image frequency which gives the same IF is f0+2*IF=2110KHz

Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Description : Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C

Last Answer : B) Double tuned transformer

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

What is the local oscillator frequency range commercial AM broadcast if it is equal to 455 KHz. A. 540 to 1600 KHz B. 0 to 1600 KHz C. 995 to 2055 KHz D. 0 to 455 KHz

Description : What is the local oscillator frequency range commercial AM broadcast if it is equal to 455 KHz. A. 540 to 1600 KHz B. 0 to 1600 KHz C. 995 to 2055 KHz D. 0 to 455 KHz

Last Answer : C. 995 to 2055 KHz

Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Description : Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Last Answer : C. 405.050 MHz

Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Description : Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Last Answer : B. 401.0125 MHz

If frequency range of 401.000MHz to 401.050MHz has to be channelized at 12.5 kHz between channel, what is the center of its first channel from the lower limit? A. 401.125MHz B. 401.00625MHz C. 401.025MHz D. 401.0125MHz

Description : If frequency range of 401.000MHz to 401.050MHz has to be channelized at 12.5 kHz between channel, what is the center of its first channel from the lower limit? A. 401.125MHz B. 401.00625MHz C. 401.025MHz D. 401.0125MHz

Last Answer : B. 401.00625MHz

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm

Description : At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm

Last Answer : D. -90 dBm

The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Description : The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Last Answer : D. 300 – 3000 MHz

ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB

Description : ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB

Last Answer : B. -90 dBm

A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz.

Description : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz. (A) 50000 (B) 0.2 (C) 600 (D) 5

Last Answer : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is 5 kHz.

What is the uplink receiver frequency if the downlink transmitter is on channel 4 (3.84 Ghz)? A. 6.065 GHz B. 6.84 GHz C. 6.65 GHz D. 6.05 GHz

Description : What is the uplink receiver frequency if the downlink transmitter is on channel 4 (3.84 Ghz)? A. 6.065 GHz B. 6.84 GHz C. 6.65 GHz D. 6.05 GHz

Last Answer : A. 6.065 GHz

What is the channel spacing for SITOR frequencies? A. 500 Hz B. 170 Hz C. 300 Hz D. 3 kHz

Description : What is the channel spacing for SITOR frequencies? A. 500 Hz B. 170 Hz C. 300 Hz D. 3 kHz

Last Answer : A. 500 Hz

What is the channel spacing for MF-HF voice frequencies? A. 2.8 kHz B. 500 Hz C. 3.5 kHz D. 3 kHz

Description : What is the channel spacing for MF-HF voice frequencies? A. 2.8 kHz B. 500 Hz C. 3.5 kHz D. 3 kHz

Last Answer : D. 3 kHz

What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz

Description : What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz

Last Answer : D. 300-3400 Hz

Nominal voice channel A. 20 to 20 KHz B. 16 to 16 KHz C. 3 to 3 KHz D. 4 KHz

Description : Nominal voice channel A. 20 to 20 KHz B. 16 to 16 KHz C. 3 to 3 KHz D. 4 KHz

Last Answer : D. 4 KHz

What do you call the service area of a standard AM broadcast where fading is allowed but not objectionable co-channel interference? A. Experimental B. Secondary C. Tertiary D. Primary

Description : What do you call the service area of a standard AM broadcast where fading is allowed but not objectionable co-channel interference? A. Experimental B. Secondary C. Tertiary D. Primary

Last Answer : B. Secondary

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Description : What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Last Answer : C. Poor front-end selectivity

A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz

Description : A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz

Last Answer : B. 6546 kHz

Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Description : Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Last Answer : C. 15 to 160 MHz

What is the approximate bandwidth of an FM system with 10 kHz of modulating frequency and a 150 kHz of frequency deviation? A. 300 kHz B. 320 kHz C. 150 kHz D. 200 kHz

Description : What is the approximate bandwidth of an FM system with 10 kHz of modulating frequency and a 150 kHz of frequency deviation? A. 300 kHz B. 320 kHz C. 150 kHz D. 200 kHz

Last Answer : B. 320 kHz

In acoustics, if the volume of the room is 200 m3 then at what frequency the coefficient of absorption is measured? A. 120 kHz B. 120 Hz C. 100 Hz D. 150 Hz

Description : In acoustics, if the volume of the room is 200 m3 then at what frequency the coefficient of absorption is measured? A. 120 kHz B. 120 Hz C. 100 Hz D. 150 Hz

Last Answer : B. 120 Hz

What is the carrier frequency of supergroup 10? A. 2724 kHz B. 2356 kHz C. 2108 kHz D. 3100 kHz

Description : What is the carrier frequency of supergroup 10? A. 2724 kHz B. 2356 kHz C. 2108 kHz D. 3100 kHz

Last Answer : D. 3100 kHz

What is the typical frequency used for communicating to submerged submarines? A. 100 Hz B. 500 Hz C. 4 kHz D. 200 Hz

Description : What is the typical frequency used for communicating to submerged submarines? A. 100 Hz B. 500 Hz C. 4 kHz D. 200 Hz

Last Answer : A. 100 Hz

Tropospheric scatter is a method of sky wave propagation for which of the following frequency bands? A. 300 kHz to 3 MHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 300 MHz to 3 GHz

Description : Tropospheric scatter is a method of sky wave propagation for which of the following frequency bands? A. 300 kHz to 3 MHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 300 MHz to 3 GHz

Last Answer : D. 300 MHz to 3 GHz

What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66

Description : What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66

Last Answer : D. 1.66

Which of the following frequency bands is best suited for sky wave propagation? A. 30 to 300 kHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 3 GHz to 30 GHz

Description : Which of the following frequency bands is best suited for sky wave propagation? A. 30 to 300 kHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 3 GHz to 30 GHz

Last Answer : B. 3 MHz to 30 MHz

Which of the following frequency bands is best suited for ground wave propagation? A. 30 to 300 kHz B. 300 kHz to 3 MHzC. 3 MHz to 30 MHz D. 30 MHz to 300 MHz

Description : Which of the following frequency bands is best suited for ground wave propagation? A. 30 to 300 kHz B. 300 kHz to 3 MHz C. 3 MHz to 30 MHz D. 30 MHz to 300 MHz

Last Answer : A. 30 to 300 kHz

What frequency is 10 octaves above 30 Hz? A. 30.72 kHz B. 30 kHz C. 300 Hz D. 307.2 kHz

Description : What frequency is 10 octaves above 30 Hz? A. 30.72 kHz B. 30 kHz C. 300 Hz D. 307.2 kHz

Last Answer : A. 30.72 kHz

What is the frequency of a 2-cm sound wave in sea water at 25˚C? A. 76 kHz B. 76 Hz C. 76 MHz D. 76 mHz

Description : What is the frequency of a 2-cm sound wave in sea water at 25˚C? A. 76 kHz B. 76 Hz C. 76 MHz D. 76 mHz

Last Answer : A. 76 kHz

Assuming a UHF frequency range of 405.0125 MHz to 405.0875 MHz at 25 kHz channeling plan, how many channels can you produce? A. 2.5 ch. B. 2 ch. C. 4 ch. D. 3 ch.

Description : Assuming a UHF frequency range of 405.0125 MHz to 405.0875 MHz at 25 kHz channeling plan, how many channels can you produce? A. 2.5 ch. B. 2 ch. C. 4 ch. D. 3 ch.

Last Answer : D. 3 ch.

The extremely high frequency (EHF) band is in the radio spectrum range of _______. A. 30 to 300 kHz B. 30 to 300 GHz C. 3 to 30 MHz D. 3 to 30 GHz

Description : The extremely high frequency (EHF) band is in the radio spectrum range of _______. A. 30 to 300 kHz B. 30 to 300 GHz C. 3 to 30 MHz D. 3 to 30 GHz

Last Answer : B. 30 to 300 GHz

For a sample rate of 40 kHz, determine the maximum analog input frequency A. 30 kHz B. 40 kHz C. 20 kHz D. 10 kHz

Description : For a sample rate of 40 kHz, determine the maximum analog input frequency A. 30 kHz B. 40 kHz C. 20 kHz D. 10 kHz

Last Answer : C. 20 kHz

Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz

Description : Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz

Last Answer : B. 15 to 160 Mhz

What is the baseband frequency of standard FDM basic supergroup? A. 312 to 552 kHz B. 300 to 600 kHz C. 60 to 2540 kHz D. 60 to 108 kHz

Description : What is the baseband frequency of standard FDM basic supergroup? A. 312 to 552 kHz B. 300 to 600 kHz C. 60 to 2540 kHz D. 60 to 108 kHz

Last Answer : A. 312 to 552 kHz

The frequency spectrum of the stereophonic FM signal. A. 67 kHz B. 59.5 to 74.5 kHz C. 19 to 38 kHz D. 30 to 53 kHz

Description : The frequency spectrum of the stereophonic FM signal. A. 67 kHz B. 59.5 to 74.5 kHz C. 19 to 38 kHz D. 30 to 53 kHz

Last Answer : D. 30 to 53 kHz

ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the same as that of the intermediate frequency C. Generates a 1kHz note for Morse code reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Description : Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Last Answer : B. The transmitter and receiver

Main basic components of a data communication are composed of the following. A. Computer, modern and router B. Computer, bridge and gateway C. Transmitter, channel and receiver D. Transmitter, computer and modem

Description : Main basic components of a data communication are composed of the following. A. Computer, modern and router B. Computer, bridge and gateway C. Transmitter, channel and receiver D. Transmitter, computer and modem

Last Answer : C. Transmitter, channel and receiver

The wavelength of visible light extends from a. 0.8 to 1.0 nm b. 400 to 750 nm c. 200 to 660 nm d. 700 to 1200 nm

Description : The wavelength of visible light extends from a. 0.8 to 1.0 nm b. 400 to 750 nm c. 200 to 660 nm d. 700 to 1200 nm

Last Answer : b. 400 to 750 nm

The mean velocity of blood flow in the aorta during systole is 1.5 × 10–2 m / s. What is the frequency change in an instrument with a signal frequency of 105 Hz (speed of sound in blood, 1570 m / s)?

Description : The mean velocity of blood flow in the aorta during systole is 1.5 × 10–2 m / s. What is the frequency change in an instrument with a signal frequency of 105 Hz (speed of sound in blood, 1570 m / s)?

Last Answer : 1060 kg/m3, very close to pure water's density of 1000 kg/m3. The average adult has a blood volume of roughly 5 litres (11 US pt) or 1.3 gallons, which is composed of plasma ... .4 million (female) erythrocytes: Red blood cells contain the blood's hemoglobin and distribute oxygen. Mature red blood

nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure

Description : nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure

Last Answer : B. Noise improvement factor

In cellular system, _____ defines the geographic distance that is required between cells using identical frequencies in order to avoid interference between the radio transmissions at these cells. A. frequency-reuse ratio B. distance-to-reuse ratio (D/R) C. reuse format plan ratio D. reuse factor

Description : In cellular system, _____ defines the geographic distance that is required between cells using identical frequencies in order to avoid interference between the radio transmissions at these cells. A. frequency-reuse ratio B. distance-to-reuse ratio (D/R) C. reuse format plan ratio D. reuse factor

Last Answer : B. distance-to-reuse ratio (D/R)

Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Description : Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Last Answer : C. Noise improvement factor

Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Description : Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Last Answer : C. Out of the band

Give the classification of tuned amplifier

Description : Give the classification of tuned amplifier

Last Answer : (i) Small signal tuned amplifier *Single tuned *Double tuned *Stagger tuned (ii) Large signal tuned amplifier.

What is the need for a tuned amplifier?

Description : What is the need for a tuned amplifier?

Last Answer : In radio or TV receivers , it is necessary to select a particular channel among all other available channels.Hence some sort of frequency selective circuit is needed that will allow us to amplify ... and reject all the other unwanted signals and this function is provided by a tuned amplifier.