Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV
Last Answer : B. 4.0 µV
Description : A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz
Last Answer : B. 660 kHz
Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz
Last Answer : C. Generates a 1kHz note for Morse code reception
Description : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz .Find local oscillator frequency and image frequency.
Last Answer : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz Intermediate frequency is 455KHz. IF frequency=f0-fs Local oscillator frequency is f0=IF +fs=455K+1200K=1655kHz The image frequency which gives the same IF is f0+2*IF=2110KHz
Description : What is the local oscillator (mixer) frequency of the satellite with an uplink frequency in GHz band? A. 3500 MHz B. 4500 MHz C. 2225 MHz D. 2555 MHz
Last Answer : C. 2225 MHz
Description : An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz
Last Answer : D. 99.7 MHz
Description : Assuming a UHF frequency range of 405.0125 MHz to 405.0875 MHz at 25 kHz channeling plan, how many channels can you produce? A. 2.5 ch. B. 2 ch. C. 4 ch. D. 3 ch.
Last Answer : D. 3 ch.
Description : Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz
Last Answer : C. 405.050 MHz
Description : Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz
Last Answer : B. 401.0125 MHz
Description : If frequency range of 401.000MHz to 401.050MHz has to be channelized at 12.5 kHz between channel, what is the center of its first channel from the lower limit? A. 401.125MHz B. 401.00625MHz C. 401.025MHz D. 401.0125MHz
Last Answer : B. 401.00625MHz
Description : The extremely high frequency (EHF) band is in the radio spectrum range of _______. A. 30 to 300 kHz B. 30 to 300 GHz C. 3 to 30 MHz D. 3 to 30 GHz
Last Answer : B. 30 to 300 GHz
Description : Which of the following circuit would be preferred for a 455 kHz IF amplifier? A) A resistance loaded B) Double tuned transformer C) Video amplifier D) Class C
Last Answer : B) Double tuned transformer
Description : The frequency tolerance of an AM radio broadcast station A. 200 Hz B. 2000 Hz C. 20 Hz D. 2 Hz
Last Answer : C. 20 Hz
Description : Which frequency band is the standard AM radio broadcast? A. HF B. UHF C. MF D. VHF
Last Answer : C. MF
Description : Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz
Last Answer : C. 15 to 160 MHz
Description : What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66
Last Answer : D. 1.66
Description : Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz
Last Answer : B. 15 to 160 Mhz
Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator
Last Answer : D. To prevent re-radiation of the local oscillator
Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier
Last Answer : D. IF amplifier
Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna
Last Answer : C. Local oscillator, mixer and RF amplifier
Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator
Last Answer : D. Local oscillator
Description : After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage
Last Answer : A. local oscillator
Description : How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz
Last Answer : B. 1.25 MHz
Description : What is the spectrum range of U600 mastergroup? A. 60 – 108 kHz B. 564 – 3084 kHz C. 312 – 552 kHz D. 60 -2788 kHz
Last Answer : B. 564 – 3084 kHz
Description : The allowable deviation ratio of commercial FM broadcast. A. 25 B. 15 C. 5 D. 75
Last Answer : C. 5
Description : A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz
Last Answer : B. 6546 kHz
Description : What is the approximate bandwidth of an FM system with 10 kHz of modulating frequency and a 150 kHz of frequency deviation? A. 300 kHz B. 320 kHz C. 150 kHz D. 200 kHz
Last Answer : B. 320 kHz
Description : In acoustics, if the volume of the room is 200 m3 then at what frequency the coefficient of absorption is measured? A. 120 kHz B. 120 Hz C. 100 Hz D. 150 Hz
Last Answer : B. 120 Hz
Description : What is the carrier frequency of supergroup 10? A. 2724 kHz B. 2356 kHz C. 2108 kHz D. 3100 kHz
Last Answer : D. 3100 kHz
Description : What is the typical frequency used for communicating to submerged submarines? A. 100 Hz B. 500 Hz C. 4 kHz D. 200 Hz
Last Answer : A. 100 Hz
Description : Tropospheric scatter is a method of sky wave propagation for which of the following frequency bands? A. 300 kHz to 3 MHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 300 MHz to 3 GHz
Last Answer : D. 300 MHz to 3 GHz
Description : Which of the following frequency bands is best suited for sky wave propagation? A. 30 to 300 kHz B. 3 MHz to 30 MHz C. 30 MHz to 300 MHz D. 3 GHz to 30 GHz
Last Answer : B. 3 MHz to 30 MHz
Description : Which of the following frequency bands is best suited for ground wave propagation? A. 30 to 300 kHz B. 300 kHz to 3 MHz C. 3 MHz to 30 MHz D. 30 MHz to 300 MHz
Last Answer : A. 30 to 300 kHz
Description : What frequency is 10 octaves above 30 Hz? A. 30.72 kHz B. 30 kHz C. 300 Hz D. 307.2 kHz
Last Answer : A. 30.72 kHz
Description : What is the frequency of a 2-cm sound wave in sea water at 25˚C? A. 76 kHz B. 76 Hz C. 76 MHz D. 76 mHz
Last Answer : A. 76 kHz
Description : For a sample rate of 40 kHz, determine the maximum analog input frequency A. 30 kHz B. 40 kHz C. 20 kHz D. 10 kHz
Last Answer : C. 20 kHz
Description : What is the baseband frequency of standard FDM basic supergroup? A. 312 to 552 kHz B. 300 to 600 kHz C. 60 to 2540 kHz D. 60 to 108 kHz
Last Answer : A. 312 to 552 kHz
Description : The frequency spectrum of the stereophonic FM signal. A. 67 kHz B. 59.5 to 74.5 kHz C. 19 to 38 kHz D. 30 to 53 kHz
Last Answer : D. 30 to 53 kHz
Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone
Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz
Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage
Last Answer : D. final RF stage
Description : One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. ... capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors
Last Answer : B. Heating of capacitor in the oscillator
Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit
Last Answer : C. Use of regulated power supply
Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley
Last Answer : B. MOPA
Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.
Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.
Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.
Last Answer : D. DC and RF heating of resistors, causing then to change values.
Description : Refer to the deviation of the operating frequency of a crystal oscillator from its nominal value due to temperature variations. A. Drift B. Flash over C. Frequency deviation D. Deviation ratio
Last Answer : A. Drift
Description : In BTU system, one BTU is equal to-----? A. 2055 Joule B. 1155 Joule C. 2155 Joule D. 1055 Joule (Answer)
Last Answer : D. 1055 Joule (Answer)
Description : Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?
Last Answer : Reason for LO frequency to be greater than signal frequency The local oscillator frequency (f0) is made greater than signal frequency (Fs) in radio receiver: Local oscillator frequency range is 995 ... frequency of desired signal because the IF is constant and same for all the incoming RF signal.
Description : A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz
Last Answer : C. 999.8 kHz, 1000 kHz, and 1000.2 kHz
Description : Where does the AM broadcast band located in the spectrum band? A. HF band B. VHF band C. LF band D. MF band
Last Answer : D. MF band