To electrically decrease the length of an antenna. A. add an inductor in series B. add an inductor in parallel C. add a resistor in series D. add a capacitor in series

To electrically decrease the length of an antenna.
A. add an inductor in series
B. add an inductor in parallel
C. add a resistor in series
D. add a capacitor in series
by

1 Answer

Answer :

D. add a capacitor in series
by

Related questions

Increasing the electrical length of an antenna means A. add an inductor in parallel B. add a capacitor in series C. add an inductor series D. add a resistor is series

Description : Increasing the electrical length of an antenna means A. add an inductor in parallel B. add a capacitor in series C. add an inductor series D. add a resistor is series

Last Answer : C. add an inductor series

How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Description : How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Last Answer : D. By connecting an inductor in series with the antenna

Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Description : Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Last Answer : A. adding a capacitor in series and reducing the physical length

To lengthen an antenna electrically, add a A. resistor B. battery C. condult D. coil

Description : To lengthen an antenna electrically, add a A. resistor B. battery C. condult D. coil

Last Answer : D. coil

When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Description : When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Last Answer : D. Antenna resonant frequency increases

What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Description : What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Last Answer : A. The antenna’s resonant frequency will increase

One of the following makes an antenna physically long but electrically short A. Adding L in series B. Adding C in series C. Top loading D. Both A and C

Description : One of the following makes an antenna physically long but electrically short A. Adding L in series B. Adding C in series C. Top loading D. Both A and C

Last Answer : B. Adding C in series

What makes an antenna physically long but electrically short? A. Top loading B. Adding C in series C. Adding L in series D. All of these

Description : What makes an antenna physically long but electrically short? A. Top loading B. Adding C in series C. Adding L in series D. All of these

Last Answer : B. Adding C in series

The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an ____________. A. capacitor B. inductor C. resistor D. transistor

Description : The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an ____________. A. capacitor B. inductor C. resistor D. transistor

Last Answer : Answer: C

The most inefficient method of voltage reduction from the stand point of power loss, is a/an _____________. A. capacitor in series with the load B. inductor in series with the load C. capacitor and inductor in series with the load D. resistor in series with the load

Description : The most inefficient method of voltage reduction from the stand point of power loss, is a/an _____________. A. capacitor in series with the load B. inductor in series with the load C. capacitor and inductor in series with the load D. resistor in series with the load

Last Answer : Answer: D

Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Description : Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Last Answer : D. loading coil

If an antenna is too short for the wavelength being used, the effective length can be increased by adding: A. capacitance in series B. inductance in series C. resistance in parallel D. resistance in series

Description : If an antenna is too short for the wavelength being used, the effective length can be increased by adding: A. capacitance in series B. inductance in series C. resistance in parallel D. resistance in series

Last Answer : B. inductance in series

The 'Choke' used with a tube light is basically – (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Description : The 'Choke' used with a tube light is basically – (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Last Answer : (1) an inductor Explanation: In electronics, a choke is an inductor used to block higher-frequency alternating current (AC) in an electrical circuit, while passing lower-frequency or direct ... created by suddenly interrupting the current in choke, which is connected in series with the tubelight.

Device used to store energy in electrical circuits is A. resistor B. inductor C. capacitor D. diode

Description : Device used to store energy in electrical circuits is A. resistor B. inductor C. capacitor D. diode

Last Answer : capacitor

insulator which is placed between 2 plates of capacitor isA. electric B. dielectric C. inductor D. resistor

Description : insulator which is placed between 2 plates of capacitor isA. electric B. dielectric C. inductor D. resistor

Last Answer : dielectric

Draw the symbol of i) Iron core inductor ii) variable capacitor iii) resistor iv) Ferrite core inductor

Description : Draw the symbol of i) Iron core inductor ii) variable capacitor iii) resistor iv) Ferrite core inductor

Last Answer :  Iron core inductor:  Ferrite core inductor:  

The ‘Choke’ used with a tube light is basically (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Description : The ‘Choke’ used with a tube light is basically (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Last Answer : an inductor

State the applications and specification of (i) Resistor (ii) Capacitor (iii)Inductor

Description : State the applications and specification of (i) Resistor (ii) Capacitor (iii)Inductor

Last Answer : Application of resistor: 1.Resistors are used in high frequency instrument. 2.Resistor is used in power control circuit. 3.It is used in DC power supplies. 4.Resistors are used ... DC Current  3.Electromagnetic Interference (EMI)  4.Magnetic Saturation Flux Density  5.Curie Temperature 

If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Description : If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Last Answer : D. decrease

One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. Heating of capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Description : One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. ... capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Last Answer : B. Heating of capacitor in the oscillator

What component in the telephone set has the primary function of interfacing the handset to the local loop? A. Varistor B. Induction coil C. Resistor D. Capacitor

Description : What component in the telephone set has the primary function of interfacing the handset to the local loop? A. Varistor B. Induction coil C. Resistor D. Capacitor

Last Answer : B. Induction coil

What component in the telephone set has the primary function of interfacing the handset to the local loop? A. Varistor B. Induction coil C. Resistor D. Capacitor

Description : What component in the telephone set has the primary function of interfacing the handset to the local loop? A. Varistor B. Induction coil C. Resistor D. Capacitor

Last Answer : B. Induction coil

What would be the physical length of a tpical coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz? A. 20 meters B. 3.51 meters C. 2.33 meters D. 0.25 meter

Description : What would be the physical length of a tpical coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz? A. 20 meters B. 3.51 meters C. 2.33 meters D. 0.25 meter

Last Answer : B. 3.51 meters

What is the phase angle of an ohm inductor in series with an ohm resistor connected to a 5 KHz source?

Description : What is the phase angle of an ohm inductor in series with an ohm resistor connected to a 5 KHz source?

Last Answer : You need to provide values of resistor and inductor etc to find the phase angle.

A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.

Description : A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.

Last Answer : ANSWER: X -- CURRENT WILL LAG BY 26 DEGREES.

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

State the advantages and disadvantages of series inductor and shunt capacitor filter.

Description : State the advantages and disadvantages of series inductor and shunt capacitor filter.

Last Answer : Advantages of series inductor filter 1. It has low ripple factor at heavy load currents (i.e. low load resistance) 2. It has no surge current through the diode. 3. It reduces the ripple in the DC ... . 3. It has low output voltages for heavy loads. 4. Ripple factor is dependent on the load.

An inductor of Q factor 10 is connected in series with a capacitor having a Q factor of 100. The overall Q factor

Description : An inductor of Q factor 10 is connected in series with a capacitor having a Q factor of 100. The overall Q factor of the circuit is :  (A) 100/11 (B) 11/100 (C) 110 (D) 1000

Last Answer : An inductor of Q factor 10 is connected in series with a capacitor having a Q factor of 100. The overall Q factor of the circuit is : 100/11

How is a wattmeter electrically connected in a circuit? A. In series B. In parallel C. In series-parallel D. Inductively

Description : How is a wattmeter electrically connected in a circuit? A. In series B. In parallel C. In series-parallel D. Inductively

Last Answer : Answer: C

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Description : Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Last Answer : D. both A and B

The parasitic element of an antenna system will A. decrease its directivity B. increase its directivity C. give the antenna unidirectional properties D. both B and C

Description : The parasitic element of an antenna system will A. decrease its directivity B. increase its directivity C. give the antenna unidirectional properties D. both B and C

Last Answer : D. both B and C

What is the RC time constant of a series RC circuit that contains a 12-megohm resistor and a 12-microfarad capacitor?

Description : What is the RC time constant of a series RC circuit that contains a 12-megohm resistor and a 12-microfarad capacitor?

Last Answer : 144 seconds (t=R x C)

At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?

Description : At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?

Last Answer : At the instant of the initiation of the action.

A simple half-wavelength antenna radiates the strongest signal A. at 45 degrees to its axis B. parallel to its axis C. at right angles to its axis D. at 60 degrees to its axis

Description : A simple half-wavelength antenna radiates the strongest signal A. at 45 degrees to its axis B. parallel to its axis C. at right angles to its axis D. at 60 degrees to its axis

Last Answer : C. at right angles to its axis

How will you increase the gain of an antenna? A. By adding several antennas in parallel B. By focusing the radiated energy in one desired direction C. By making antenna rods thicker D. By making the antenna size larger

Description : How will you increase the gain of an antenna? A. By adding several antennas in parallel B. By focusing the radiated energy in one desired direction C. By making antenna rods thicker D. By making the antenna size larger

Last Answer : B. By focusing the radiated energy in one desired direction

To limit the current flow through a DC voltmeter to as low a value as possible, the moving coil circuit is provided with a/an _____________. A. high series resistance B. high parallel resistance C. series inductor D. external shunt

Description : To limit the current flow through a DC voltmeter to as low a value as possible, the moving coil circuit is provided with a/an _____________. A. high series resistance B. high parallel resistance C. series inductor D. external shunt

Last Answer : Answer: A

Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Description : Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Last Answer : B. The location of the antenna with respect to nearby objects

In the case if Marconi antenna, the actual length if the radiating element is A. one-half wavelength B. one-quarter wavelength C. one wavelength D. one-eight wavelength

Description : In the case if Marconi antenna, the actual length if the radiating element is A. one-half wavelength B. one-quarter wavelength C. one wavelength D. one-eight wavelength

Last Answer : B. one-quarter wavelength

What is the usual electrical length of a driven element in an HF beam antenna? A. ¼ wavelength B. ¾ wavelength C. ½ wavelength D. 1 wavelength

Description : What is the usual electrical length of a driven element in an HF beam antenna? A. ¼ wavelength B. ¾ wavelength C. ½ wavelength D. 1 wavelength

Last Answer : C. ½ wavelength

What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Description : What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Last Answer : D. The frequency range over which an antenna can be expected to operate satisfactorily

If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its resonant frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Description : If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its ... frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Last Answer : C. its resonant frequency will be increased

The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Description : The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Last Answer : B. 44 MHz

The length of a Marconi antenna to operate with 985 kHz is ______. A. 200 ft B. 500 ft C. 250 ft D. 999 ft

Description : The length of a Marconi antenna to operate with 985 kHz is ______. A. 200 ft B. 500 ft C. 250 ft D. 999 ft

Last Answer : C. 250 ft

Part of a microwave link can be approximated by free space conditions. The antenna gain are each 40 dB, the frequency is 10 GHz, and the path length is 80 km. Calculate the receive power for a transmitted power of 10 W? A. 0.871 μW B. 871 μW C. 0.871 mW D. 871 nW

Description : Part of a microwave link can be approximated by free space conditions. The antenna gain are each 40 dB, the frequency is 10 GHz, and the path length is 80 km. Calculate the receive power for a transmitted power of 10 W? A. 0.871 μW B. 871 μW C. 0.871 mW D. 871 nW

Last Answer : A. 0.871 μW

The typical length of the rhombic antenna is ____. A. 2λ to 8λ B. 10λ to 20λ C. 1λ to 3λ D. 5λ to 10λ

Description : The typical length of the rhombic antenna is ____. A. 2λ to 8λ B. 10λ to 20λ C. 1λ to 3λ D. 5λ to 10λ

Last Answer : A. 2λ to 8λ

What is meant by the term antenna bandwidth A. Antenna length divided by the number of elements. B. The angle between the half-power radiation points C. The frequency range over which and antenna can be expected to perform well D. The angle formed between two imaginary line drawn through the ends of the elements

Description : What is meant by the term antenna bandwidth A. Antenna length divided by the number of elements. B. The angle between the half-power radiation points C. The frequency range over which and antenna ... perform well D. The angle formed between two imaginary line drawn through the ends of the elements

Last Answer : C. The frequency range over which and antenna can be expected to perform well

The frequency of operation of a dipole antenna cut to length of 3.4 m. A. 42.9 MHz B. 61.3 MHz C. 38.5 MHz D. 53.5 MHz

Description : The frequency of operation of a dipole antenna cut to length of 3.4 m. A. 42.9 MHz B. 61.3 MHz C. 38.5 MHz D. 53.5 MHz

Last Answer : A. 42.9 MHz

The component used for tuning a radio is basically a variable – (1) Resistor (2) Condenser (3) Inductor (4) Transformer

Description : The component used for tuning a radio is basically a variable – (1) Resistor (2) Condenser (3) Inductor (4) Transformer

Last Answer : (2) Condenser Explanation: A tuning capacitor or tuning condenser is a variable capacitor used in an electronic circuit of a radio. It usually connects in parallel to a loop antenna and its capacitance may be intentionally and repeatedly changed mechanically or electronically.

A component that allows only unidirectional current to pass through it is A. resistor B. inductor C. transformer D. diode

Description : A component that allows only unidirectional current to pass through it is A. resistor B. inductor C. transformer D. diode

Last Answer : diode