The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.
by

1 Answer

Answer :

The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be 4.

by

Related questions

Determine the standing wave ratio of a 300-Ω line whose load is 400+j150 Ω. A. 3.55 B. 1.67 C. 5.53 D. 3.35

Description : Determine the standing wave ratio of a 300-Ω line whose load is 400+j150 Ω. A. 3.55 B. 1.67 C. 5.53 D. 3.35

Last Answer : B. 1.67

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Description : A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Last Answer : D. 112 Ω

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Description : An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Last Answer : B. Either A or C

Find the standing wave ratio, when a load impedance of 250 ohm is connected to a 75 ohm line. a) 0.3 b) 75 c) 250 d) 3.33

Description : Find the standing wave ratio, when a load impedance of 250 ohm is connected to a 75 ohm line. a) 0.3 b) 75 c) 250 d) 3.33

Last Answer : d) 3.33

What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150Ω D. 2 Ω

Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω

Last Answer : C. 150 Ω

It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Description : It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Last Answer : A. when comparing the gains of directional antennas

Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Last Answer : D. The standing wave ratio is one.

When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern hemisphere) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Last Answer : A. When comparing the gains of directional antennas

The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Description : The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Last Answer : A. 1

For transmission line, the incident voltage Ei = 6V, and Er = 3V. Calculate: (1) Reflection coefficient (2) Standing wave ratio

Description : For transmission line, the incident voltage Ei = 6V, and Er = 3V. Calculate: (1) Reflection coefficient (2) Standing wave ratio

Last Answer : (1)Reflection coefficient  (2) Standing wave ratio (1)Reflection coefficient Reflection coefficient R=Er/Ei  =3/6  R=0.5 (2) Standing wave ratio SWR=Ei+Er/Ei-Er  =6+3/6-3  SWR =3

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system

Description : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

Last Answer : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: 1200 Hz

A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Last Answer : Solution :

If Voltage Standing Wave Ratio, (VSWR) of a wave is 2, its reflection coefficient will be _____.

Description : If Voltage Standing Wave Ratio, (VSWR) of a wave is 2, its reflection coefficient will be _____.

Last Answer : If Voltage Standing Wave Ratio, (VSWR) of a wave is 2, its reflection coefficient will be 1/3.

A waveguide may also be terminated in a resistive load that is matched to the characteristic impedance of the waveguide. The resistive load is most often called a _____

Description : A waveguide may also be terminated in a resistive load that is matched to the characteristic impedance of the waveguide. The resistive load is most often called a _____

Last Answer : Dummy resistor

A single-phase transmission line of impedance j 0.8 ohm supplies a resistive...

Description :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is?

Last Answer :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is 0.6 lagging.

A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the

Description : A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and ... reactances are neglected, the primary current is  A)1.41A B)2A C) 2.24A D)3A

Last Answer : A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and leakage reactances are neglected, the primary current is 2.24A

A travelling wave of surge resistance, Ro on a transmission line is terminated by a load resistance, RL...

Description : A travelling wave of surge resistance, Ro on a transmission line is terminated by a load resistance, RL. If RL > Ro then there is (A) no reflected wave (B) partial reflection of reversal ... (C) partial reflection of reversal of voltage only (D) reflection of reversal of both current and voltage

Last Answer : A travelling wave of surge resistance, Ro on a transmission line is terminated by a load resistance, RL. If RL > Ro then there is partial reflection of reversal of current only

What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Description : What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Last Answer : A. Velocity factor

For matched line, the standing wave ratio will be a) 0 b) ∞ c) -1 d) 1

Description : For matched line, the standing wave ratio will be a) 0 b) ∞ c) -1 d) 1

Last Answer : d) 1

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Last Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is ...

Description : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

Last Answer : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is 150 W

The parameters of Transmission line are R = 50 Ω/ km, L= 1mH/km ,C = 0.1µf/km, G = 2µV/km. calculate characteristic impedance.

Description : The parameters of Transmission line are R = 50 Ω/ km, L= 1mH/km ,C = 0.1µf/km, G = 2µV/km. calculate characteristic impedance.

Last Answer : The parameters of Transmission line are R = 50 Ω/ km, L= 1mH/km ,C = 0.1µf/km, G = 2µV/km. calculate characteristic impedance.

For a transmission line open circuit and short circuit impedances are 20 Ω and 5 Ω. Then characteristic

Description : For a transmission line open circuit and short circuit impedances are 20 Ω and 5 Ω. Then characteristic impedance is: (1) 100 Ω (2) 50 Ω (3) 25 Ω (4) 10 Ω

Last Answer : For a transmission line open circuit and short circuit impedances are 20 Ω and 5 Ω. Then characteristic impedance is: 10 Ω

If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge

Description : If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge factor is :  (A) 2.8 (B) 2.6 (C) 4.6 (D) 3.6

Last Answer : If Poisson's ratio of a resistance wire strain gauge is 1.8, then neglecting piezo-resistive effects, its Gauge factor is : 4.6

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

Description : For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

Last Answer : For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is 0.707 lead

Results in reduction in the power of light wave as it travels down the cable. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Description : Results in reduction in the power of light wave as it travels down the cable. ∙ A. power loss ∙ B. absorption loss ∙ C. resistive loss ∙ D. heat loss

Last Answer : A. power loss

What will be the reflection coefficient of the wave of load connected to transmission line if surge impedance of the line is equal to load ? (a) Zero (b) Unity (c) Infinity (d) None of the above

Description : What will be the reflection coefficient of the wave of load connected to transmission line if surge impedance of the line is equal to load ? (a) Zero (b) Unity (c) Infinity (d) None of the above

Last Answer : (a) Zero

When a wave propagates on a transmission line, it suffers reflection several times at (a) tapping (b) load end (c) sending end (d) sending and other end (e) all of the above

Description : When a wave propagates on a transmission line, it suffers reflection several times at (a) tapping (b) load end (c) sending end (d) sending and other end (e) all of the above

Last Answer : (d) sending and other end

The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω

Description : The input terminal impedance at the center of a folded dipole antenna is A. 72 Ω B. 300 Ω C. 50 Ω D. 73 Ω

Last Answer : B. 300 Ω

The standing wave ratio of short circuited and open circuited lines will be a) 0 b) 1 c) -1 d) ∞

Description : The standing wave ratio of short circuited and open circuited lines will be a) 0 b) 1 c) -1 d) ∞

Last Answer : d) ∞

The range of the standing wave ratio is a) 0 < S < 1 b) -1 < S < 1 c) 1 < S < ∞ d) 0 < S < ∞

Description : The range of the standing wave ratio is a) 0 < S < 1 b) -1 < S < 1 c) 1 < S < ∞ d) 0 < S < ∞

Last Answer : c) 1 < S < ∞

The maxima and minima voltage of the standing wave are 6 and 2 respectively. The standing wave ratio is a) 2 b) 3 c) 1/2 d) 4

Description : The maxima and minima voltage of the standing wave are 6 and 2 respectively. The standing wave ratio is a) 2 b) 3 c) 1/2 d) 4

Last Answer : b) 3

Standing wave ratio is defined as the a) Ratio of voltage maxima to voltage minima b) Ratio of current maxima to current minima c) Product of voltage maxima and voltage minima d) Product of current maxima and current minima

Description : Standing wave ratio is defined as the a) Ratio of voltage maxima to voltage minima b) Ratio of current maxima to current minima c) Product of voltage maxima and voltage minima d) Product of current maxima and current minima

Last Answer : a) Ratio of voltage maxima to voltage minima

What is the square of the voltage standing-wave ratio called?

Description : What is the square of the voltage standing-wave ratio called?

Last Answer : Power standing-wave ratio (pswr).

Ratio of the velocity of propagation of a light ray in free space to the velocity of propagation of a light ray in free space in a given material. ∙ A. refractive index ∙ B. standing wave ratio ∙ C. velocity factor ∙ D. propagation velocity

Description : Ratio of the velocity of propagation of a light ray in free space to the velocity of propagation of a light ray in free space in a given material. ∙ A. refractive index ∙ B. standing wave ratio ∙ C. velocity factor ∙ D. propagation velocity

Last Answer : ∙ A. refractive index

Define standing wave ratio.

Description : Define standing wave ratio. 

Last Answer : Standing wave ratio is defined as the ratio of maximum voltage (Vmax) to minimum voltage (Vmin). Standing wave ratio is also defined as the ratio of maximum current (Imax) to minimum current (Imin).

When adjusting an RF filter on a transmitter using a dummy load, how much watts dissipation should it stand to test a 150 watts transmitter? A. 75 watts B. 300 watts C. 50 watts D. 150 watts

Description : When adjusting an RF filter on a transmitter using a dummy load, how much watts dissipation should it stand to test a 150 watts transmitter? A. 75 watts B. 300 watts C. 50 watts D. 150 watts

Last Answer : D. 150 watts

A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2 , the depth of the joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

What is the power factor in pure resistive , capacitive , inductive load ?

Description : What is the power factor in pure resistive , capacitive , inductive load ?

Last Answer : Answer : Power factor cosΦ = 1 in pure resistive load, cosΦ = 0 in capacitive load , cosΦ = 0 in inductive load .

Is computer is Resistive load?

Description : Is computer is Resistive load?

Last Answer : It is resistive much load

For an Resistive Load and Inductive load considered for switching operation of circuit breaker, Switching of which load is difficult and Why?

Description : For an Resistive Load and Inductive load considered for switching operation of circuit breaker, Switching of which load is difficult and Why?

Last Answer : In case of switching resistive load, current and voltage will be in phase i.e,when during current zero voltage also will be zero in case of resistive load. Hence the voltage at the ... maximum. This results in re-striking of arc once again. Therefore switching inductive load will be difficult

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

The energy dissipated by a resistive load is most often in what form?

Description : The energy dissipated by a resistive load is most often in what form?

Last Answer : Heat.

When a waveguide is terminated in a resistive load, the load must be matched to what property of the waveguide?

Description : When a waveguide is terminated in a resistive load, the load must be matched to what property of the waveguide?

Last Answer : . Characteristic impedance.

One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Last Answer : d. To prevent reradiation of the local oscillator

Single-phase Midpoint controlled rectifier with Resistive load

Description : Single-phase Midpoint controlled rectifier with Resistive load

Last Answer : Single-phase Midpoint controlled rectifier with Resistive load:  1) During positive half cycle of AC supply, a is positive with respect to b , this makes T1 forward biased and T2 is reverse ... voltage reverses the polarity and T2 is turned off. The operation is as shown in waveforms.