Find the standing wave ratio, when a load impedance of 250 ohm is connected to a 75 ohm line. a) 0.3 b) 75 c) 250 d) 3.33

Find the standing wave ratio, when a load impedance of 250 ohm is connected to a 75 ohm
line.
a) 0.3
b) 75
c) 250
d) 3.33
by

1 Answer

Answer :

d) 3.33
by

Related questions

The minimum impedance of a 75 ohm transmission line with a SWR of 2.5 is a) 100 b) 50 c) 25 d) 30

Description : The minimum impedance of a 75 ohm transmission line with a SWR of 2.5 is a) 100 b) 50 c) 25 d) 30

Last Answer : d) 30

A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Last Answer : Solution :

The maximum impedance of a 50 ohm transmission line with SWR of 3 is a) 50/3 b) 3/50 c) 150 d) 450

Description : The maximum impedance of a 50 ohm transmission line with SWR of 3 is a) 50/3 b) 3/50 c) 150 d) 450

Last Answer : c) 150

For matched line, the standing wave ratio will be a) 0 b) ∞ c) -1 d) 1

Description : For matched line, the standing wave ratio will be a) 0 b) ∞ c) -1 d) 1

Last Answer : d) 1

Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Last Answer : D. The standing wave ratio is one.

The intrinsic impedance of free space is given by a) 272 ohm b) 412 ohm c) 740 ohm d) 377 ohm

Description : The intrinsic impedance of free space is given by a) 272 ohm b) 412 ohm c) 740 ohm d) 377 ohm

Last Answer : d) 377 ohm

The standing wave ratio of short circuited and open circuited lines will be a) 0 b) 1 c) -1 d) ∞

Description : The standing wave ratio of short circuited and open circuited lines will be a) 0 b) 1 c) -1 d) ∞

Last Answer : d) ∞

The range of the standing wave ratio is a) 0 < S < 1 b) -1 < S < 1 c) 1 < S < ∞ d) 0 < S < ∞

Description : The range of the standing wave ratio is a) 0 < S < 1 b) -1 < S < 1 c) 1 < S < ∞ d) 0 < S < ∞

Last Answer : c) 1 < S < ∞

The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

Description : The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

Last Answer : The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be 4.

A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Description : A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Description : A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

The maxima and minima voltage of the standing wave are 6 and 2 respectively. The standing wave ratio is a) 2 b) 3 c) 1/2 d) 4

Description : The maxima and minima voltage of the standing wave are 6 and 2 respectively. The standing wave ratio is a) 2 b) 3 c) 1/2 d) 4

Last Answer : b) 3

Standing wave ratio is defined as the a) Ratio of voltage maxima to voltage minima b) Ratio of current maxima to current minima c) Product of voltage maxima and voltage minima d) Product of current maxima and current minima

Description : Standing wave ratio is defined as the a) Ratio of voltage maxima to voltage minima b) Ratio of current maxima to current minima c) Product of voltage maxima and voltage minima d) Product of current maxima and current minima

Last Answer : a) Ratio of voltage maxima to voltage minima

Standing waves occurs due to a) Impedance match b) Impedance mismatch c) Reflection d) Transmission

Description : Standing waves occurs due to a) Impedance match b) Impedance mismatch c) Reflection d) Transmission

Last Answer : b) Impedance mismatch

What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Description : What is the term for the ratio of actual velocity at which a signal travels through a line to the speed of light in a vacuum? A. Velocity factor B. Characteristic impedance C. Surge impedance D. Standing wave ratio

Last Answer : A. Velocity factor

What will be the reflection coefficient of the wave of load connected to transmission line if surge impedance of the line is equal to load ? (a) Zero (b) Unity (c) Infinity (d) None of the above

Description : What will be the reflection coefficient of the wave of load connected to transmission line if surge impedance of the line is equal to load ? (a) Zero (b) Unity (c) Infinity (d) None of the above

Last Answer : (a) Zero

The phase shift in the electric and magnetic fields in an EM wave is given by which parameter? a) phase constant b) attenuation constant c) propagation constant d) intrinsic impedance

Description : The phase shift in the electric and magnetic fields in an EM wave is given by which parameter? a) phase constant b) attenuation constant c) propagation constant d) intrinsic impedance

Last Answer : d) intrinsic impedance

The total power of a wave with average power 15 units in a surface density of 0.5 units is a) 15 b) 30 c) 7.5 d) 0.75

Description : The total power of a wave with average power 15 units in a surface density of 0.5 units is a) 15 b) 30 c) 7.5 d) 0.75

Last Answer : c) 7.5

Calculate the ratio of sine of incident angle to the sine of reflected angle when the refractive indices of medium 1 and 2 are given as 2.33 and 1.66 respectively. a) 0.71 b) 1.4 c) 2 d) 3.99

Description : Calculate the ratio of sine of incident angle to the sine of reflected angle when the refractive indices of medium 1 and 2 are given as 2.33 and 1.66 respectively. a) 0.71 b) 1.4 c) 2 d) 3.99

Last Answer : a) 0.71

The intrinsic impedance is the ratio of square root of a) Permittivity to permeability b) Permeability to permittivity c) Phase constant to wavelength d) Wavelength to phase constant

Description : The intrinsic impedance is the ratio of square root of a) Permittivity to permeability b) Permeability to permittivity c) Phase constant to wavelength d) Wavelength to phase constant

Last Answer : b) Permeability to permittivity

It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Description : It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Last Answer : A. when comparing the gains of directional antennas

Determine the standing wave ratio of a 300-Ω line whose load is 400+j150 Ω. A. 3.55 B. 1.67 C. 5.53 D. 3.35

Description : Determine the standing wave ratio of a 300-Ω line whose load is 400+j150 Ω. A. 3.55 B. 1.67 C. 5.53 D. 3.35

Last Answer : B. 1.67

When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern hemisphere) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Last Answer : A. When comparing the gains of directional antennas

The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Description : The standing wave ratio is equal to ________ if the load is properly matched with the transmission line. A. 1 B. 50 C. 10 D. 2

Last Answer : A. 1

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

Find the dissipation factor when series resistance is 5 ohm and capacitive resistance is 10 unit. a) 2 b) 0.5 c) 1 d) 0

Description : Find the dissipation factor when series resistance is 5 ohm and capacitive resistance is 10 unit. a) 2 b) 0.5 c) 1 d) 0

Last Answer : b) 0.5

Find the time constant in a series R-L circuit when the resistance is 4 ohm and the inductance is 2 H. a) 0.25 b) 0.2 c) 2 d) 0.5

Description : Find the time constant in a series R-L circuit when the resistance is 4 ohm and the inductance is 2 H. a) 0.25 b) 0.2 c) 2 d) 0.5

Last Answer : d) 0.5

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

A single-phase transmission line of impedance j 0.8 ohm supplies a resistive...

Description :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is?

Last Answer :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is 0.6 lagging.

Find the flux density of line charge of radius (cylinder is the Gaussian surface) 2m and charge density is 3.14 units? a) 1 b) 0.75 c) 0.5 d) 0.25

Description : Find the flux density of line charge of radius (cylinder is the Gaussian surface) 2m and charge density is 3.14 units? a) 1 b) 0.75 c) 0.5 d) 0.25

Last Answer : d) 0.25

As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100.

Description : As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is A) 25 A B) 50 A C) 100 A D) 200A

Last Answer : As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is 50 A

The effective skin resistance of a material with conductivity 120 and skin depth of 2μm is a) 4.16 kilo ohm b) 4.16 mega ohm c) 41.6 kilo ohm d) 41.6 mega ohm

Description : The effective skin resistance of a material with conductivity 120 and skin depth of 2μm is a) 4.16 kilo ohm b) 4.16 mega ohm c) 41.6 kilo ohm d) 41.6 mega ohm

Last Answer : a) 4.16 kilo ohm

Find the current in a conductor with resistance 2 ohm, electric field 2 units and distance 100cm. a) 1A b) 10mA c) 10A d) 100mA

Description : Find the current in a conductor with resistance 2 ohm, electric field 2 units and distance 100cm. a) 1A b) 10mA c) 10A d) 100mA

Last Answer : a) 1A

The resistivity of a material with resistance 200 ohm, length 10m and area twice that of the length is a) 200 b) 300 c) 400 d) 500

Description : The resistivity of a material with resistance 200 ohm, length 10m and area twice that of the length is a) 200 b) 300 c) 400 d) 500

Last Answer : c) 400

What is the end impedance of a half-wave dipole? A. 73 Ω B. 72 Ω C. 250 Ω D. 2500 Ω

Description : What is the end impedance of a half-wave dipole? A. 73 Ω B. 72 Ω C. 250 Ω D. 2500 Ω

Last Answer : D. 2500 Ω

The numerical aperture of a coaxial cable with core and cladding indices given by 2.33 and 1.4 respectively is a) 3.73 b) 0.83 c) 3.46 d) 1.86

Description : The numerical aperture of a coaxial cable with core and cladding indices given by 2.33 and 1.4 respectively is a) 3.73 b) 0.83 c) 3.46 d) 1.86

Last Answer : d) 1.86

The input impedance of a short circuited loss less transmission line of characteristic impedance 50 Ohm is

Description : The input impedance of a short circuited loss less transmission line of characteristic impedance 50 Ohm is

Last Answer : Capacitive

The lossless line of characteristics impedance 300 Ohm is terminated in a pure resistance of 200 Ohm.

Description : The lossless line of characteristics impedance 300 Ohm is terminated in a pure resistance of 200 Ohm. The value of the standing wave ratio is  (a) 1.5 (b) 0.67 (c) 1.0 (d) 1.25

Last Answer : The lossless line of characteristics impedance 300 Ohm is terminated in a pure resistance of 200 Ohm. The value of the standing wave ratio is 1.5

The magnitude of the open-circuit and short circuit input impedance of a transmission line are 100 ohm and...

Description : The magnitude of the open-circuit and short circuit input impedance of a transmission line are 100 ohm and 25 ohm respectively. The characteristic impedance of line is:  (1) 25 ohm (2) 50 ohm (3) 75 ohm (4) 100 ohm

Last Answer : The magnitude of the open-circuit and short circuit input impedance of a transmission line are 100 ohm and 25 ohm respectively. The characteristic impedance of line is 25 ohm.

Find the Cartesian coordinates of B(4,250,1200) a) (0.845, 1.462, 3.625) b) (-0.845, 1.462, 3.625) c) (-8.45, 2.462, 6.325) d) (8.45, 2.462, 6.325)

Description : Find the Cartesian coordinates of B(4,250,1200) a) (0.845, 1.462, 3.625) b) (-0.845, 1.462, 3.625) c) (-8.45, 2.462, 6.325) d) (8.45, 2.462, 6.325)

Last Answer : b) (-0.845, 1.462, 3.625)

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V,

Description : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The ... (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

Last Answer : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum ... supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively 20, 50 Hz

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Description : Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Last Answer : D. load connected to the output end of a transmission line

The expression for intrinsic impedance is given by a) √(με) b) (με) c) √(μ/ε) d) (μ/ε)

Description : The expression for intrinsic impedance is given by a) √(με) b) (με) c) √(μ/ε) d) (μ/ε)

Last Answer : c) √(μ/ε)

The intrinsic impedance of free space is a) 489 b) 265 c) 192 d) 377

Description : The intrinsic impedance of free space is a) 489 b) 265 c) 192 d) 377

Last Answer : d) 377

What is the meaning of the term “velocity factor” of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial cable. C. The velocity of the wave on the transmission line multiplied by the velocity of light in a vacuum. D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of light in vacuum C. The ratio of the characteristic impedance of the line to the terminating impedance D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Description : What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

[75] Two transformers are connected in parallel. These transformers do not have equal percentage impedance which results A. Short-circuiting of the secondaries B. Power factor of one of the transformers is leading while that of the other lagging C. Transformers having higher copper losses will have negligible core losses D. Loading of the transformers not in proportion to their kVA ratings.

Description : [75] Two transformers are connected in parallel. These transformers do not have equal percentage impedance which results A. Short-circuiting of the secondaries B. Power factor of one of the ... have negligible core losses D. Loading of the transformers not in proportion to their kVA ratings.

Last Answer : D. Loading of the transformers not in proportion to their kVA ratings

The benefit of Maxwell equation is that a) Any parameter can be calculated b) Antenna can be designed c) Polarisation of the wave can be calculated d) Transmission line constants can be found

Description : The benefit of Maxwell equation is that a) Any parameter can be calculated b) Antenna can be designed c) Polarisation of the wave can be calculated d) Transmission line constants can be found

Last Answer : a) Any parameter can be calculated

The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted

Description : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be

Last Answer : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be 0.5 Ohm