Description : The illustrated lead acid battery is about to be placed in service. The negitive plate, labeled 'E', is made of_______. EL-0031 A. sponge lead (Pb) B. lead peroxide (PbO2) C. lead sulfate (PbSO4) D. zinc oxide (ZnO2)
Last Answer : Answer: A
Description : If the illustrated device is fully discharged, what will be the result? EL-0061 A. The battery will be short circuited because the mud space will be filled with lead sulfate B. The electrolyte ... minimum sulfuric acid. D. The plates will be maximum lead oxide and sponge lead minimum lead sulfate.
Last Answer : Answer: C
Description : If the illustrated device is fully discharged, what will be the result? EL-0061 A. The plates will be maximum lead sulfate minimum sponge lead and lead oxide, the electrolyte will be ... lead oxide and sponge lead minimum lead sulfate, the electrolyte will be maximum water minimum sulfuric acid
Description : Which of the processes listed occurs during the charging of a lead-acid storage battery? A. Negative plates change to lead peroxide. B. Positive plates change to lead peroxide. C. Both plates change to lead peroxide. D. Both plates change to lead sulfate.
Last Answer : Answer: B
Description : In the illustration, the component labeled 'G' is ______. EL-0031 A. hard rubber, plastic or bituminous composition B. porous inside to absorb excess positive ions C. precharged for (-) and (+) in manufacturing D. All the above
Description : The plates of a NiCad storage battery are made of ________. A. potassium hydroxide with a small amount of sulfuric acid B. lead and lead peroxide C. silver oxide and lead sulfate D. combinations of nickel powder and nickel & cadmium salts
Last Answer : Answer: D
Description : Caution must be exercised during the charging of lead-acid storage batteries as _____________. A. the acid will become weaker B. hydrogen gas is being continuously liberated C. both plates are changing chemically to lead sulfate D. lead peroxide in the negative plate is poisonous
Description : Which of the problems listed will occur if a lead-acid battery is allowed to remain in a discharged condition for a long period of time? A. The battery may be unable to accept a full charge ... . C. The concentrated sulfuric acid will attack the lead peroxide plates. D. The separators will harden.
Description : When charging lead-acid batteries, the charging rate should be reduced as the battery nears its full charge to ____________. A. prevent damaging battery plates B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation
Description : When charging lead-acid batteries, you should reduce the charging rate as the battery nears its full charge capacity to ______________. A. prevent excessive gassing and overheating B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation
Description : In the illustration, the component labeled 'G' _________. EL-0031 A. is lined with cardboard to maintain a moisture (electrolyte) barrier between cells B. is a one piece container with compartments for each individual cell C. must be UL approved for shipboard use D. can only contain one cell
Description : In the illustration, the component 'B' is attached to the component 'G' by _________. EL-0031 A. melting the top of 'G' and pressing 'B' onto it B. 'C' holding it in place C. sealing compound made of bituminous substance D. vacuum created in the battery by electrolytic action
Description : In the illustrated 450 VAC system, what should be provided between the bus and the device labeled 'F'? EL-0003 A. a potential transformer B. a current transformer C. an emergency disconnect device D. an audible alarm and indicating light
Description : In the illustrated device, the part labeled '1A' _________. EL-0001 A. are start and run windings for a single phase shaded pole induction motor B. is the stator for a polyphase induction ... armature for a squirrel cage rotor motor D. are direct current shunt field windings for a universal motor
Description : Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on ... be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.
Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value
Description : Which of the following conditions indicates that a lead-acid battery is being charged too rapidly? A. Sparks occurring at the positive terminal. B. Unusually high electrolyte specific gravity. C. Low plate potentials being developed. D. Excessively high temperatures and gassing rates.
Description : Which of the following activities occurs during the charging process of a lead-acid storage battery? A. The specific gravity of the acid increases. B. Both plates change chemically to lead sulfate. C. The specific gravity of the acid decreases. D. Hydrogen gas is absorbed.
Description : The electrolyte used in a nickel-cadmium battery is distilled water and ______________. A. diluted sulfuric acid B. potassium hydroxide C. lead sulfate D. zinc oxide
Description : In the illustration, if one of the devices labeled 'TURB' should fail the ___________. EL-0003 A. device labeled 'EXC' will drive the alternator B. device labeled 'BKR' for that ... -alternator D. emergency generator should automatically start and be placed on line to supply emergency load centers
Description : From the standpoint of safety, you should never allow salt water to enter a leadacid storage battery or come in contact with sulfuric acid because ______________. A. the resulting gas is ... peroxide D. combining salt water with lead-acid creates an invisible gas resulting in severe corrosion
Description : Which of the listed components does line 'C' represent for the transistor illustrated? EL-0068 A. Grid B. Plate C. Emitter D. Collector
Description : Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent ... D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components
Description : What is the total current of the illustrated circuit if the battery is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps
Description : The illustrated circuits are used to measure ___________. EL-0024 A. resistance B. gauss or magnetic field strength C. battery discharge rate in Amp-hours D. current
Description : In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts
Description : In the illustrated circuit, what is the resistance across R2 if the battery voltage is 32 VDC, the resistance of R1 is 1.2 kohms and the current through R2 is 18.82 milliamps? EL-0036 A. 500 ohms B. 1,200 ohms C. 10 ohms D. The answer can not be found with the information given.
Description : In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts
Description : What is the total resistance of the electrical circuit illustrated if the resistance of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.01 ohms B. 0.10 ohms C. 1.00 ohms D. 10.00 ohms
Description : In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days
Description : In the illustrated circuit, if the battery is 24 VDC, the resistance of R1 is 24 ohms, and the resistance of R2 is 24 ohms, the total current is _________. EL-0019 A. 2 amps B. 1 amp C. 1/2 amp D. 2.4 amps
Description : What is the current flowing through R3 of the illustrated circuit if the battery is 12 VDC and resistance of R1 is 2 ohms, R2 is 3 ohms, and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps
Description : What is the current through R2 of the circuit illustrated if the resistances of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.5 amp B. 1.5 amps C. 3.0 amps D. 6 amps
Description : What is the current flow through R1 of the circuit illustrated if the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms with a 12 VDC battery? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps
Description : What is the current flowing through R1 of the illustrated circuit with a 6 VDC battery if the resistance of R1 is 2 ohms, R2 is 4 ohms and R3 is 4 ohms? EL-0021 A. 0.5 amps B. 1.5 amps C. 3.0 amps D. 6 amps
Description : What is the total current in the illustrated circuit with a 6 volt battery if the resistance of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms? EL-0021 A. 0.6 amp B. 1 amp C. 4 amps D. 6 amps
Description : Which of the substances listed should be applied to battery terminals to help prevent corrosion? A. Zinc chromate B. Naval jelly C. Lead peroxide D. Petroleum jelly
Description : The circuit illustrated represents a 2 wire DC ground detecting system. If the positive bus is grounded and the test button is pushed, which of the lamps will be brightest? EL-0008 A. X B. Y C. both will be equal brightness. D. both will go out.
Description : If reading AC current with the illustrated device and unsure of the range as a precaution , the first step should be to _________. EL-0047 A. secure power and test for voltage B. disconnect the ... resistance and use Ohm's law to calculate current D. unable to safely measure current with the device
Description : In the illustrated motor controller circuit, which statment is true? EL-0023 A. The high and low speed lights operate at less than line voltage with a resistor in series. B. This controller can be ... . The wattage of the high speed light must be greater than the wattage of the low speed light.
Description : Which of the following statments is true of the illustrated motor controller? EL-0023 A. The low speed is used for starting the motor and when the controller automaticly shifts to High speed. B. The HOL relay ... D. If the overload relay opens for high speed the motor can still be run in low speed.
Description : If reading the AC voltage from the line lead of a 440 VAC controller the range switch illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. Unable to safely read with this meter.
Description : If the illustrated test is being performed to determine which winding is grounded and the light does not come on then __________. EL-0027 A. winding is grounded and you should continue on to the ... the windings but probabily in the pecker head, you should check and retape the line lead connections
Description : If the illustrated motor fails to start and gives a loud hum when the start button is pushed, the problem is ________. EL-0007 A. one of the phases to the motor is not energized because of ... electrical distribution system D. 'OL1' is open because of 'T1' overload causing the motor to single phase
Description : Violent gassing developed by a lead-acid battery during charging indicates that the ____________. A. plate separators are grounded B. cell voltages are excessive C. specific gravity in insufficient D. charging rate is excessive
Description : The specific gravity of the electrolyte in a lead-acid battery is measured by a _____________. A. gould plate B. titration pipette C. hydrometer D. litmus paper test
Description : Violent gassing from a lead-acid battery while it is being charged, indicates that the _____________. A. plate separators are grounded B. battery compartment ventilation is inadequate C. electrolyte specific gravity is too low D. charging rate is too high
Description : If violent gassing occurs when a lead-acid storage battery is first placed on charge, the _____________. A. battery must be given an emergency charge B. charging rate is too low C. charging rate is too high D. specific gravity of the electrolyte solution is too low
Description : Which of the following problems is indicated if a lead-acid battery begins to gas violently when it is first placed on charge? A. Insufficient compartment ventilation is being provided. B. A short ... undergoing its normal charging rate. D. An excessive charging rate is being applied to the battery.
Description : The positive plants of nickel iron cell is made up of a. Nickel hydroxide b. Lead peroxide c. Ferrous hydroxide d. Potassium hydroxide
Last Answer : a. Nickel hydroxide