When testing a capacitor with an analog type ohmmeter, a good capacitor will be indicated when _____________. A. there is no meter deflection B. the meter deflects to a low resistance value and remains there C. the meter deflects to a low resistance value and slowly increases towards infinity D. the meter deflects to a low resistance value and increases rapidly to a higher value, but stays fairly low

When testing a capacitor with an analog type ohmmeter, a good capacitor will be indicated when _____________. A. there is no meter deflection B. the meter deflects to a low resistance value and remains there C. the meter deflects to a low resistance value and slowly increases towards infinity D. the meter deflects to a low resistance value and increases rapidly to a higher value, but stays fairly low
by

1 Answer

Answer :

Answer: C
by

Related questions

Which of the following conditions indicates a short circuited capacitor when checking its condition with an ohmmeter? A. The capacitor shows charging, but the final resistance reading is appreciably less than normal. B. The reading is practically zero and remains there. C. The capacitor shows no charging action, but indicates a very high resistance. D. The pointer moves quickly to the low resistance side of the scale, then slowly recedes toward infinity.

Description : Which of the following conditions indicates a short circuited capacitor when checking its condition with an ohmmeter? A. The capacitor shows charging, but the final resistance reading is appreciably less ... moves quickly to the low resistance side of the scale, then slowly recedes toward infinity.

Last Answer : Answer: B

Which of the listed statements is correct when using an analog multimeter as an ohmmeter? A. The pointer should be adjusted to zero each time a new resistance range is selected. B. The pointer will move to infinity when the meter is not in use. C. Ohmmeters are not sufficiently sized to measure conductor insulation resistance. D. All of the above.

Description : Which of the listed statements is correct when using an analog multimeter as an ohmmeter? A. The pointer should be adjusted to zero each time a new resistance range is selected. B. The ... C. Ohmmeters are not sufficiently sized to measure conductor insulation resistance. D. All of the above.

Last Answer : Answer: D

When troubleshooting motor controllers, a shorted relay or contactor coil is often indicated by _______________. A. a resistance reading of 'infinity' on an ohmmeter B. charred insulation and/or a blown control fuse C. a reading of 'zero' on a megger from one of the coil's leads to ground D. a higher-than-normal voltage reading across the winding

Description : When troubleshooting motor controllers, a shorted relay or contactor coil is often indicated by _______________. A. a resistance reading of 'infinity' on an ohmmeter B. charred insulation and/or a blown ... of the coil's leads to ground D. a higher-than-normal voltage reading across the winding

Last Answer : Answer: B

A capacitor can be tested using a megohmmeter or an ohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value for the capacitor B. first swing quickly to 'zero', then gradually move up the scale as the capacitor charges C. immediately deflect to and remain at zero D. immediately swing to a high reading and then gradually decrease

Description : A capacitor can be tested using a megohmmeter or an ohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance ... deflect to and remain at zero D. immediately swing to a high reading and then gradually decrease

Last Answer : Answer: C

Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointers to mid-scale B. change the meter's batteries C. center the meter's pointer at infinity D. short the test leads and calibrate the meter

Description : Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointers to mid-scale B. change the meter's batteries C. center the meter's pointer at infinity D. short the test leads and calibrate the meter

Last Answer : Answer: D

Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointer to mid-scale B. short the test leads and calibrate the meter reading to 'zero' C. change the meter's batteries D. center the meter's pointer at infinity

Description : Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointer to mid-scale B. short the test leads and calibrate the meter reading to 'zero' C. change the meter's batteries D. center the meter's pointer at infinity

Last Answer : Answer: B

When a megohmmeter is being used to test insulation resistance, current leakage along the surface of the insulation is indicated by the megohmmeter pointer _____________. A. fluctuating around a constant resistance reading B. dipping towards 'zero', then rising slowly C. kicking slightly downscale as voltage is applied D. continually rising as the test voltage is applied

Description : When a megohmmeter is being used to test insulation resistance, current leakage along the surface of the insulation is indicated by the megohmmeter pointer _____________. A. fluctuating around a ... slightly downscale as voltage is applied D. continually rising as the test voltage is applied

Last Answer : Answer: C

While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Description : While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Last Answer : Answer: B

The basic meter movement responds to the flow of current through its coil. Therefore, this meter movement may be used as a/an _____________. A. voltmeter by placing a resistance in parallel with the coil B. ohmmeter by placing another meter movement in parallel with the coil C. wattmeter by placing a battery in parallel with the coil D. ammeter by placing a low resistance in parallel with the coil

Description : The basic meter movement responds to the flow of current through its coil. Therefore, this meter movement may be used as a/an _____________. A. voltmeter by placing a resistance in parallel with the ... in parallel with the coil D. ammeter by placing a low resistance in parallel with the coil

Last Answer : Answer: D

When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a low resistance initially...

Description : When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a low resistance initially and then slowly came to infinity position. This shows that capacitor is ?

Last Answer : When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a low resistance initially and then slowly came to infinity position. This shows that capacitor is all right.

When a megohmmeter is being used to test insulation resistance, current leakage along the surface of the insulation is indicated by the megohmmeter's pointer _____________. A. dipping toward zero then raising slowly B. continually rising as test voltage is applied C. kicking slightly down scale as voltage is applied D. fluctuating around a constant resistance reading

Description : When a megohmmeter is being used to test insulation resistance, current leakage along the surface of the insulation is indicated by the megohmmeter's pointer _____________. A. dipping toward ... kicking slightly down scale as voltage is applied D. fluctuating around a constant resistance reading

Last Answer : Answer: C

You are testing the insulation in an AC generator with a megohmeter. The resistance value of a dry, clean winding will ____________. A. continue to rise as the test potential is maintained, becoming fairly steady as the leakage current stabilizes B. remain constant as the temperature of the windings increases C. continue to drop as the potential is maintained, becoming fairly steady after 5 to 7 minutes D. stabilize after approximately 2 to 4 minutes of fluctuation

Description : You are testing the insulation in an AC generator with a megohmeter. The resistance value of a dry, clean winding will ____________. A. continue to rise as the test potential is maintained, ... fairly steady after 5 to 7 minutes D. stabilize after approximately 2 to 4 minutes of fluctuation

Last Answer : Answer: A

Before using a volt-ohmmeter to measure resistance readings, you should _____________. A. replace all batteries B. test the insulation resistance of the leads C. make sure the test leads do not touch D. hold the leads together and 'zero' the meter

Description : Before using a volt-ohmmeter to measure resistance readings, you should _____________. A. replace all batteries B. test the insulation resistance of the leads C. make sure the test leads do not touch D. hold the leads together and 'zero' the meter

Last Answer : Answer: D

A grounded switch or cable will be indicated by a megohmmeter reading of _____________. A. infinity B. 'zero' C. being unsteady in the high range D. being unsteady in the low range

Description : A grounded switch or cable will be indicated by a megohmmeter reading of _____________. A. infinity B. 'zero' C. being unsteady in the high range D. being unsteady in the low range

Last Answer : Answer: B

The final step in testing a circuit for a ground involves the use of a megohmmeter. A grounded switch or cable will be indicated by a megohmmeter reading of ____________. A. 'zero' B. infinity C. steady in the high range D. unsteady in the low range

Description : The final step in testing a circuit for a ground involves the use of a megohmmeter. A grounded switch or cable will be indicated by a megohmmeter reading of ____________. A. 'zero' B. infinity C. steady in the high range D. unsteady in the low range

Last Answer : Answer: A

A capacitor is to be tested with a megohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value B. deflect to zero and remain at that position C. swing to a high reading and gradually decrease D. swing to zero then gradually increase with slight pointer movements down scale

Description : A capacitor is to be tested with a megohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value ... and gradually decrease D. swing to zero then gradually increase with slight pointer movements down scale

Last Answer : Answer: B

When you are testing the gain of an audio-frequency transistor with an ohmmeter, what is indicated by a 10-to-1 resistance ratio?

Description : When you are testing the gain of an audio-frequency transistor with an ohmmeter, what is indicated by a 10-to-1 resistance ratio?

Last Answer : Normal gain.

A low voltage source is being used for testing armature coils. A coil short circuit will be indicated by a _______. A. high voltage reading, while the other coil readings will have an equal or lower value B. low or zero voltage reading, while the other coils will have higher readings C. fluctuating voltmeter reading, while the other coil readings are steady D. steady voltmeter reading, while the other coil readings are fluctuating

Description : A low voltage source is being used for testing armature coils. A coil short circuit will be indicated by a _______. A. high voltage reading, while the other coil readings will have an ... the other coil readings are steady D. steady voltmeter reading, while the other coil readings are fluctuating

Last Answer : Answer: B

A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Description : A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Last Answer : Answer: D

When you are using an ohmmeter to test a transistor for leakage, what is indicated by a low, but not shorted, reverse resistance reading?

Description : When you are using an ohmmeter to test a transistor for leakage, what is indicated by a low, but not shorted, reverse resistance reading?

Last Answer : A leaking transistor

When the voltage remains constant and the resistance is increased in a series circuit, the flow of current _____________. A. increases by the square of the original value B. increases C. remains the same D. decreases

Description : When the voltage remains constant and the resistance is increased in a series circuit, the flow of current _____________. A. increases by the square of the original value B. increases C. remains the same D. decreases

Last Answer : Answer: D

Conductor resistance may be INDIRECTLY measured by using a/an _____________. A. voltmeter only B. ammeter only C. voltmeter and an ammeter D. ohmmeter only

Description : Conductor resistance may be INDIRECTLY measured by using a/an _____________. A. voltmeter only B. ammeter only C. voltmeter and an ammeter D. ohmmeter only

Last Answer : Answer: C

With both ends of a three conductor cable disconnected and arranged without the conductors touching each other, an ohmmeter reading of 'zero' ohms between the ends of one conductor would indicate _____________. A. continuity B. a partial ground C. the resistance is infinite D. a short circuit

Description : With both ends of a three conductor cable disconnected and arranged without the conductors touching each other, an ohmmeter reading of 'zero' ohms between the ends of one conductor would indicate _____________. A. continuity B. a partial ground C. the resistance is infinite D. a short circuit

Last Answer : Answer: A

When the length and cross sectional area of a wire are both tripled, the resistance _____________. A. increases nine fold B. increases three fold C. remains the same D. decreases six fold

Description : When the length and cross sectional area of a wire are both tripled, the resistance _____________. A. increases nine fold B. increases three fold C. remains the same D. decreases six fold

Last Answer : Answer: C

When the voltage remains constant, and the resistance increases in a series circuit, current flow _____________. A. decreases B. remains the same C. increases D. increases by the square

Description : When the voltage remains constant, and the resistance increases in a series circuit, current flow _____________. A. decreases B. remains the same C. increases D. increases by the square

Last Answer : Answer: A

When using a megohmmeter to test insulation, good insulation will be indicated by _____________. A. slight kicks of the needle down scale B. a downward dip followed by a gradual climb to the true resistance value C. a gradual rise in the pointer reading at the outset D. the initial dip of the pointer

Description : When using a megohmmeter to test insulation, good insulation will be indicated by _____________. A. slight kicks of the needle down scale B. a downward dip followed by a gradual climb to the true resistance ... C. a gradual rise in the pointer reading at the outset D. the initial dip of the pointer

Last Answer : Answer: B

Prior to using an analog type ohmmeter, the leads are purposely shorted together. Which of the following actions should be taken if, when adjusting to 'zero' ohms, the indicating needle can not be returned to 'zero' on the scale? A. The lead clips should be replaced. B. The batteries should be replaced. C. The test reading should be added to each final reading. D. The test reading should be subtracted from each final reading.

Description : Prior to using an analog type ohmmeter, the leads are purposely shorted together. Which of the following actions should be taken if, when adjusting to 'zero' ohms, the indicating needle can not be ... be added to each final reading. D. The test reading should be subtracted from each final reading.

Last Answer : Answer: B

The state of charge of a lead acid storage battery is best indicated by the _____________. A. testing of the individual cell voltages B. ampere hour capacity of the battery C. specific gravity of the electrolyte D. total cell voltages

Description : The state of charge of a lead acid storage battery is best indicated by the _____________. A. testing of the individual cell voltages B. ampere hour capacity of the battery C. specific gravity of the electrolyte D. total cell voltages

Last Answer : Answer: C

A milliammeter, with a full scale deflection reading of 100 milliamps, is known to have an accuracy of + or - 2%. A meter reading of 10 milliamps would indicate a line current of between _____________. A. 9.8 and 10.0 milliamperes B. 9.8 and 10.2 milliamperes C. 8.0 and 12.0 milliamperes D. 8.0 and 10.0 milliamperes

Description : A milliammeter, with a full scale deflection reading of 100 milliamps, is known to have an accuracy of + or - 2%. A meter reading of 10 milliamps would indicate a line current of between _____________. A. 9.8 ... 9.8 and 10.2 milliamperes C. 8.0 and 12.0 milliamperes D. 8.0 and 10.0 milliamperes

Last Answer : Answer: B

A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre? (A) 5 mm (B) 0.5 mm (C) 0.05 mm (D) 0.005 mm

Description : A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre? (A) 5 mm (B) 0.5 mm (C) 0.05 mm (D) 0.005 mm

Last Answer : (A) 5 mm

When checking a diode with an ohmmeter, what is indicated by two high resistance measurements?

Description : When checking a diode with an ohmmeter, what is indicated by two high resistance measurements?

Last Answer : The diode is open or has a high-forward resistance.

When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors are tight B. test each resistor and capacitor on the card with an ohmmeter C. check the continuity of all printed circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit

Description : When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors ... circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit

Last Answer : Answer: A

. A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Description : . A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Last Answer : Zero.

A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Description : A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Last Answer : Zero.

An AC circuit has capacitance arranged in series. If the line voltage remains constant, the capacitive reactance value can be varied by changing the _____________. A. line frequency B. resistance C. number of commutating poles D. number of interpoles

Description : An AC circuit has capacitance arranged in series. If the line voltage remains constant, the capacitive reactance value can be varied by changing the _____________. A. line frequency B. resistance C. number of commutating poles D. number of interpoles

Last Answer : Answer: A

If the voltage applied to a moving disk frequency meter decreases, while the applied frequency remains the same, the frequency indication will _____________. A. increase B. decrease C. remain the same D. oscillate

Description : If the voltage applied to a moving disk frequency meter decreases, while the applied frequency remains the same, the frequency indication will _____________. A. increase B. decrease C. remain the same D. oscillate

Last Answer : Answer: C

When a megohmmeter is being used on a alternating current machine, the meter pointer will dip toward 'zero' and then gradually rise to the true resistance value if the motor insulation is _____________. A. grounded B. good C. shorted D. dirty

Description : When a megohmmeter is being used on a alternating current machine, the meter pointer will dip toward 'zero' and then gradually rise to the true resistance value if the motor insulation is _____________. A. grounded B. good C. shorted D. dirty

Last Answer : Answer: B

The true power indicated by a wattmeter depends on the current flow through the load, the magnitude of the potential across the load, and the _____________. A. power factor of the load B. angle of coil displacement C. inertia of the movable coil D. high resistance from the load

Description : The true power indicated by a wattmeter depends on the current flow through the load, the magnitude of the potential across the load, and the _____________. A. power factor of the load B. angle of coil displacement C. inertia of the movable coil D. high resistance from the load

Last Answer : Answer: A

As the reflux ratio in a distillation column is increased from the minimum, the (A) Slope of the operating line in stripping section decreases (B) Number of plates decreases very slowly first and then more and more rapidly (C) Total cost first decreases and then increases (D) Liquid flow increases while the vapor flow decreases for a system

Description : As the reflux ratio in a distillation column is increased from the minimum, the (A) Slope of the operating line in stripping section decreases (B) Number of plates decreases very slowly first ... decreases and then increases (D) Liquid flow increases while the vapor flow decreases for a system

Last Answer : (C) Total cost first decreases and then increases

On increasing the reverse bias to a large value in a p-n junction diode current (a) Increases slowly (b) Remains fixed (c) Suddenly increases (d) Decreases slowly

Description : On increasing the reverse bias to a large value in a p-n junction diode current (a) Increases slowly (b) Remains fixed (c) Suddenly increases (d) Decreases slowly

Last Answer : (c) Suddenly increases

A testing device called a 'growler' is being used to locate a shorted coil in the stator of an AC electrical machine. When the 'feeler' is moved over a slot containing the shorted coil _____________. A. a loud growling noise will be heard B. any vibration within the feeler will cease C. the meter needle will be deflected to zero D. the meter needle will be deflected to full-scale

Description : A testing device called a 'growler' is being used to locate a shorted coil in the stator of an AC electrical machine. When the 'feeler' is moved over a slot containing the shorted coil _____________. ... . the meter needle will be deflected to zero D. the meter needle will be deflected to full-scale

Last Answer : Answer: A

As shown in the illustration, which of the listed actions of the synchroscope pointer is occurring? EL-0002 A. Revolving slowly in the slow direction. B. Revolving rapidly in the slow direction. C. Revolving rapidly in the fast direction. D. It would be stationary at the 12 o'clock position since the leading edges of the A phases are in phase.

Description : As shown in the illustration, which of the listed actions of the synchroscope pointer is occurring? EL-0002 A. Revolving slowly in the slow direction. B. Revolving rapidly in the slow direction. C. ... stationary at the 12 o'clock position since the leading edges of the A phases are in phase.

Last Answer : Answer: C

The following is true of anti-H.pylori therapy except: A. It is indicated in all patients of peptic ulcer B. Resistance to any single antimicrobial drug develops rapidly C. Concurrent suppression of gastric acid enhances efficacy of the regimen D. Colloidal bismuth directly inhibits H.pylori but has poor patient acceptability

Description : The following is true of anti-H.pylori therapy except: A. It is indicated in all patients of peptic ulcer B. Resistance to any single antimicrobial drug develops rapidly C. Concurrent ... efficacy of the regimen D. Colloidal bismuth directly inhibits H.pylori but has poor patient acceptability

Last Answer : A. It is indicated in all patients of peptic ulcer

When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Description : When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Last Answer : Answer: B

A parachute descends slowly whereas a stone dropped from the same height falls rapidly, because– (1) Stone is heavier than parachute (2) Special mechanisms are present in parachute (3) A parachute has a larger surface area and air resistance is more (4) None of these

Description : A parachute descends slowly whereas a stone dropped from the same height falls rapidly, because– (1) Stone is heavier than parachute (2) Special mechanisms are present in parachute (3) A parachute has a larger surface area and air resistance is more (4) None of these

Last Answer : (3) A parachute has a larger surface area and air resistance is more Explanation: Gravity is pulling the man down while friction with the air slows him down. With the parachute out it adds more ... his parachute can make his downward speed vary between about 110 mph and 225 mph-using air resistance.

A parachute descends slowly whereas a stone dropped from the same height falls rapidly, because (1) stone is heavier than parachute (2) special mechanisms are present in parachute (3) a parachute has a larger surface area and air resistance is more (4) None of these

Description : A parachute descends slowly whereas a stone dropped from the same height falls rapidly, because (1) stone is heavier than parachute (2) special mechanisms are present in parachute (3) a parachute has a larger surface area and air resistance is more (4) None of these

Last Answer : a parachute has a larger surface area and air resistance is more