Which of the following statements describes the effects of ambient temperature on local action within lead-acid storage batteries? A. Increasing ambient temperature increases local action. B. Increasing ambient temperature decreases local action. C. Ambient temperature has no effect on local action. D. At 90°F all local action virtually ceases.

Which of the following statements describes the effects of ambient temperature on local action within lead-acid storage batteries? A. Increasing ambient temperature increases local action. B. Increasing ambient temperature decreases local action. C. Ambient temperature has no effect on local action. D. At 90°F all local action virtually ceases.
by

1 Answer

Answer :

Answer: A
by

Related questions

When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the battery amp-hour rating C. the source of power for charging should be 2.5 volts per cell D. gassing within the battery decreases when nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Description : When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the ... nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Last Answer : Answer: C

Which of the following represents the corrected specific gravity of a lead acid battery, with a temperature of 90°F, and a hydrometer reading of 1160? A. 1150 B. 1156 C. 1160 D. 1164

Description : Which of the following represents the corrected specific gravity of a lead acid battery, with a temperature of 90°F, and a hydrometer reading of 1160? A. 1150 B. 1156 C. 1160 D. 1164

Last Answer : Answer: D

Which of the following statements describes the significance of ambient temperature in relation to the service life of electronic components? A. Ambient temperature should be as high as possible to drive off moisture. B. Increased ambient temperature decreases the service life of electronic components. C. Ambient temperature is not significant as long as the relative humidity is kept low. D. A reduced ambient temperature causes a corresponding reduced service life.

Description : Which of the following statements describes the significance of ambient temperature in relation to the service life of electronic components? A. Ambient temperature should be as high as possible to drive ... is kept low. D. A reduced ambient temperature causes a corresponding reduced service life.

Last Answer : Answer: B

Local action in a dry-cell, or lead-acid storage battery is the process whereby ________________. A. hydrogen gas is liberated B. the electrolyte compensates for overcharging C. potassium hydroxide absorbs carbon dioxide from the air D. the battery becomes discharged without being connected to a load

Description : Local action in a dry-cell, or lead-acid storage battery is the process whereby ________________. A. hydrogen gas is liberated B. the electrolyte compensates for overcharging C. potassium hydroxide ... carbon dioxide from the air D. the battery becomes discharged without being connected to a load

Last Answer : Answer: D

Which of the following activities occurs during the charging process of a lead-acid storage battery? A. The specific gravity of the acid increases. B. Both plates change chemically to lead sulfate. C. The specific gravity of the acid decreases. D. Hydrogen gas is absorbed.

Description : Which of the following activities occurs during the charging process of a lead-acid storage battery? A. The specific gravity of the acid increases. B. Both plates change chemically to lead sulfate. C. The specific gravity of the acid decreases. D. Hydrogen gas is absorbed.

Last Answer : Answer: A

At high discharge rates, nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. require fewer cells for the same voltage and less mounting space B. are able to produce higher voltages and do not have to be charged as often C. can be charged and discharged many times without much damage D. have no individual cells to replace at the end of useful life

Description : At high discharge rates, nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. require fewer cells for the same voltage and less mounting space B. are able to ... times without much damage D. have no individual cells to replace at the end of useful life

Last Answer : Answer: C

Nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. put out higher voltages and require no maintenance B. can remain idle and keep a full charge for a long time C. need fewer cells in series and use less mounting space D. all of the above

Description : Nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. put out higher voltages and require no maintenance B. can remain idle and keep a full charge for a long time C. need fewer cells in series and use less mounting space D. all of the above

Last Answer : Answer: B

Caution must be exercised during the charging of lead-acid storage batteries as _____________. A. the acid will become weaker B. hydrogen gas is being continuously liberated C. both plates are changing chemically to lead sulfate D. lead peroxide in the negative plate is poisonous

Description : Caution must be exercised during the charging of lead-acid storage batteries as _____________. A. the acid will become weaker B. hydrogen gas is being continuously liberated C. both plates are changing chemically to lead sulfate D. lead peroxide in the negative plate is poisonous

Last Answer : Answer: B

The charging of lead-acid storage batteries will always result in __________. A. dangerous acid burns B. a dangerously explosive gas being liberated C. the danger of lead poisoning D. all of the above

Description : The charging of lead-acid storage batteries will always result in __________. A. dangerous acid burns B. a dangerously explosive gas being liberated C. the danger of lead poisoning D. all of the above

Last Answer : Answer: B

Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with decrease in pressure ratio C. It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Description : Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with ... It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Last Answer : ANSWER : A

Unless it can be shown that a 45°C ambient temperature will not be exceeded, motors within a machinery space must be designed for an ambient temperature of _____________. A. 45°C B. 50°C C. 55°C D. 60°C

Description : Unless it can be shown that a 45°C ambient temperature will not be exceeded, motors within a machinery space must be designed for an ambient temperature of _____________. A. 45°C B. 50°C C. 55°C D. 60°C

Last Answer : Answer: B

Increasing concave length_______ seed separation at diminishing rate a) Increases b) Decreases c)No effect d) None of the

Description : Increasing concave length_______ seed separation at diminishing rate a) Increases b) Decreases c)No effect d) None of the

Last Answer : a) Increases

Consider the following statements 1. Large cold storage plants use ammonia as refrigerant while domestic refrigerators use chlorofluorocarbons. 2. Ammonia can be liquefied at ambient temperatures and at low pressures. 3. Chlorofluorocarbons are air pollutants. The correct statement(s) is/are: (a) 1 and 3 only (b) 2 and 3 only (c) 1, 2 and 3 (d) 3 only

Description : Consider the following statements 1. Large cold storage plants use ammonia as refrigerant while domestic refrigerators use chlorofluorocarbons. 2. Ammonia can be liquefied at ambient temperatures and at low pressures. 3. Chlorofluorocarbons are ... 3 only (b) 2 and 3 only (c) 1, 2 and 3 (d) 3 only

Last Answer : Ans:(a)

Nickel-cadmium batteries are superior to lead-acid batteries at high discharge rates because they _______________. A. deliver a large amount of power and can be recharged in a shorter time B. need fewer cells in connected series and less mounting space C. have higher output voltages and require no maintenance D. all of the above

Description : Nickel-cadmium batteries are superior to lead-acid batteries at high discharge rates because they _______________. A. deliver a large amount of power and can be recharged in a shorter time B. need ... less mounting space C. have higher output voltages and require no maintenance D. all of the above

Last Answer : Answer: A

Which one of the following statements are correct for reciprocating air compressor? A. Its volumetric efficiency increases with increasing clearance ratio B. Its volumetric efficiency increases with pressure ratio C. Its volumetric efficiency does not vary with change in clearance ratio and pressure ratio D. Its volumetric efficiency decreases with increasing clearance ratio and pressure ratio

Description : Which one of the following statements are correct for reciprocating air compressor? A. Its volumetric efficiency increases with increasing clearance ratio B. Its volumetric efficiency increases ... ratio D. Its volumetric efficiency decreases with increasing clearance ratio and pressure ratio

Last Answer : ANSWER : D

increasing the capacity of a screen __________ the screen effectiveness. (A) Decreases (B) Increases (C) Does not effect (D) None of these

Description : increasing the capacity of a screen __________ the screen effectiveness. (A) Decreases (B) Increases (C) Does not effect (D) None of these

Last Answer : (A) Decreases

A lead-acid battery is considered fully charged when the ______________. A. electrolyte gasses freely B. battery charger ammeter indicates a positive reading C. terminal voltage reaches a constant value at a given temperature D. specific gravity of all cells reaches the correct value and no longer increases over a period of 1 to 4 hours

Description : A lead-acid battery is considered fully charged when the ______________. A. electrolyte gasses freely B. battery charger ammeter indicates a positive reading C. terminal voltage reaches a constant value at a ... cells reaches the correct value and no longer increases over a period of 1 to 4 hours

Last Answer : Answer: D

When troubleshooting a lead-acid storage battery, a weak or dead cell is best detected by _________________. A. measuring and comparing all cells' specific gravity B. taking an open circuit voltage test of individual cells C. visually inspecting the electrolyte levels of each cell D. taking each cell's temperature with a calibrated mercury thermometer

Description : When troubleshooting a lead-acid storage battery, a weak or dead cell is best detected by _________________. A. measuring and comparing all cells' specific gravity B. taking an open circuit ... electrolyte levels of each cell D. taking each cell's temperature with a calibrated mercury thermometer

Last Answer : Answer: A

Common nickel-cadmium and nickel-iron storage batteries utilize _______________. A. acid primary cells B. alkaline primary cells C. acid secondary cells D. alkaline secondary cells

Description : Common nickel-cadmium and nickel-iron storage batteries utilize _______________. A. acid primary cells B. alkaline primary cells C. acid secondary cells D. alkaline secondary cells

Last Answer : Answer: D

High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ percent. (A) 5 to 10 (B) 15 to 25 (C) 45 to 50 (D) 75 to 80

Description : High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ ... to 10 (B) 15 to 25 (C) 45 to 50 (D) 75 to 80

Last Answer : (C) 45 to 50

What are the effects of temperature in lead acid battery?

Description : What are the effects of temperature in lead acid battery?  

Last Answer : Higher electrolyte temp - ah capacity increases but life reduces. Lower electrolytic temp - ah capacity reduces since chemical reaction rate reduces. 

When Alternator excitation increases and machine is operating at lagging power factor then a) I increase b) I decreases c) No effect on current d) None

Description : When Alternator excitation increases and machine is operating at lagging power factor then a) I increase b) I decreases c) No effect on current d) None

Last Answer : Ans: I increase

A disadvantage of using the configuration in the illustrated circuit is _________. EL-0045 A. no current gain B. high input resistance C. high voltage gain D. becomes unstable with an increase of ambient temperature

Description : A disadvantage of using the configuration in the illustrated circuit is _________. EL-0045 A. no current gain B. high input resistance C. high voltage gain D. becomes unstable with an increase of ambient temperature

Last Answer : Answer: A

One item listed on the name plate of a cargo pump motor is 'degrees centigrade rise.' This number is based on _____________. A. normal temperature change from cold to hot B. an ambient temperature of 40°C C. minimum heat rise from no load to full load D. maximum degrees centigrade rise from absolute zero

Description : One item listed on the name plate of a cargo pump motor is 'degrees centigrade rise.' This number is based on _____________. A. normal temperature change from cold to hot B. an ambient temperature ... . minimum heat rise from no load to full load D. maximum degrees centigrade rise from absolute zero

Last Answer : Answer: B

Ambient temperature is the _____________. A. amount of temperature rise with no load B. amount of temperature developed by an operating motor C. temperature of the compartment where the motor is located D. normal operating temperature, less the room temperature

Description : Ambient temperature is the _____________. A. amount of temperature rise with no load B. amount of temperature developed by an operating motor C. temperature of the compartment where the motor is located D. normal operating temperature, less the room temperature

Last Answer : Answer: C

Ambient temperature is the _____________. A. amount of temperature rise with no load B. temperature of the compartment where the motor is located C. normal operating temperature, less the room temperature D. amount of temperature developed by an operating motor

Description : Ambient temperature is the _____________. A. amount of temperature rise with no load B. temperature of the compartment where the motor is located C. normal operating temperature, less the room temperature D. amount of temperature developed by an operating motor

Last Answer : Answer: B

Motor name plate data includes '°°C rise'. This indicates the _____________. A. actual running temperature of the winding from no load to full load B. permissible temperature rise of the windings above the designed ambient temperature C. maximum allowable temperature rise above normal full load operating temperature D. maximum allowable temperature rise for continuous no load service

Description : Motor name plate data includes '°°C rise'. This indicates the _____________. A. actual running temperature of the winding from no load to full load B. permissible temperature rise ... above normal full load operating temperature D. maximum allowable temperature rise for continuous no load service

Last Answer : Answer: B

Three 12 volt, lead-acid, batteries connected in series will develop __________. A. 12 volts B. 24 volts C. 36 volts D. 48 volts

Description : Three 12 volt, lead-acid, batteries connected in series will develop __________. A. 12 volts B. 24 volts C. 36 volts D. 48 volts

Last Answer : Answer: C

When lead-acid batteries are charging, they always give off hydrogen gas that is _____________. A. considered inert B. highly explosive C. extremely toxic D. heavier than air

Description : When lead-acid batteries are charging, they always give off hydrogen gas that is _____________. A. considered inert B. highly explosive C. extremely toxic D. heavier than air

Last Answer : Answer: B

When charging lead-acid batteries, the charging rate should be reduced as the battery nears its full charge to ____________. A. prevent damaging battery plates B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Description : When charging lead-acid batteries, the charging rate should be reduced as the battery nears its full charge to ____________. A. prevent damaging battery plates B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Last Answer : Answer: A

Routine maintenance of lead acid batteries should include _____________. A. keeping the terminals clean B. coating cable connections with petroleum jelly C. maintaining a trickle charge D. all of the above

Description : Routine maintenance of lead acid batteries should include _____________. A. keeping the terminals clean B. coating cable connections with petroleum jelly C. maintaining a trickle charge D. all of the above

Last Answer : Answer: D

When charging lead-acid batteries, you should reduce the charging rate as the battery nears its full charge capacity to ______________. A. prevent excessive gassing and overheating B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Description : When charging lead-acid batteries, you should reduce the charging rate as the battery nears its full charge capacity to ______________. A. prevent excessive gassing and overheating B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Last Answer : Answer: A

Valve Regulated Lead Acid (VRLA) Batteries Advantages

Description : Valve Regulated Lead Acid (VRLA) Batteries Advantages

Last Answer : Valve Regulated Lead Acid (VRLA) Batteries are popularly termed as maintenance free lead acid batteries. Each cell in VRLA battery will have a value (automating operating) to allow the gas ... same voltage of the cells, to continue in using existing charging equipment VRLA batteries are economical

Breathing loss" on storage of gasoline occurs due to the (A) Presence of unsaturated air (B) Fluctuation of ambient temperature during day and night (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Breathing loss" on storage of gasoline occurs due to the (A) Presence of unsaturated air (B) Fluctuation of ambient temperature during day and night (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (B) Fluctuation of ambient temperature during day and night

The absorptivity of a grey body at a given temperature __________ with increasing wavelength of radiation. (A) Increases (B) Decreases (C) Remain constant (D) May increase or decrease; depends on the material

Description : The absorptivity of a grey body at a given temperature __________ with increasing wavelength of radiation. (A) Increases (B) Decreases (C) Remain constant (D) May increase or decrease; depends on the material

Last Answer : (D) May increase or decrease; depends on the material

Pick out the wrong statement pertaining to solvent extraction of oil. Rate of extraction (A) Decreases with decrease of thickness of the flakes(B) Increases with the increasing flake size keeping the flake thicknessconstant(C) Increases considerably with the rise of temperature(D) Decreases as the moisture content of flakes increases

Description : Pick out the wrong statement pertaining to solvent extraction of oil. Rate of extraction (A) Decreases with decrease of thickness of the flakes (B) Increases with the increasing flake size ... considerably with the rise of temperature (D) Decreases as the moisture content of flakes increases

Last Answer : (D) Decreases as the moisture content of flakes increases

The ink of a pen leaks out in an airplane because (a) Atmospheric pressure increases (b) Pressure of ink inside is more than the ambient pressure (c) High speed of the aeroplane (d) Temperature difference

Description : The ink of a pen leaks out in an airplane because (a) Atmospheric pressure increases (b) Pressure of ink inside is more than the ambient pressure (c) High speed of the aeroplane (d) Temperature difference

Last Answer : Ans:(b)

The torque and current curves for a three-phase induction motor with a cage rotor, are shown in the illustration. Which of the following statements is true concerning the depicted curves? EL-0056 A. As slip increases, rotor reactance decreases. B. The pullout point on the torque curve is about seven times the normal full load torque value. C. At stand still, stator current is 150% of normal. D. If the motor is loaded to the point where 40% slip has resulted, it will stall.

Description : The torque and current curves for a three-phase induction motor with a cage rotor, are shown in the illustration. Which of the following statements is true concerning the depicted curves? EL-0056 A. As slip ... D. If the motor is loaded to the point where 40% slip has resulted, it will stall.

Last Answer : Answer: D

Which of the following statements is true concerning a stepdown transformer in an operating AC power circuit? A. Voltage and current will both be increased. B. Voltage and current will both be decreased C. Voltage decreases as current increases. D. Voltage increases as current decreases.

Description : Which of the following statements is true concerning a stepdown transformer in an operating AC power circuit? A. Voltage and current will both be increased. B. Voltage and current will both be decreased C. Voltage decreases as current increases. D. Voltage increases as current decreases.

Last Answer : Answer: C

In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to _____________. A. allow accurate zeroing of the meter B. help the windings to cool to ambient temperature C. release any residual capacitive charge from the windings D. help the windings to cool to the same temperature as the ground test connection

Description : In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to _____________. A. allow accurate zeroing of the meter ... the windings D. help the windings to cool to the same temperature as the ground test connection

Last Answer : Answer: C

Electric motors intended for use outside the engine room and boiler room are frequently rated to run at a designed ambient temperature of 40°C. What is the equivalent temperature in degrees Fahrenheit? A. 54.2°F B. 72.0°F C. 104.0°F D. 129.6°F

Description : Electric motors intended for use outside the engine room and boiler room are frequently rated to run at a designed ambient temperature of 40°C. What is the equivalent temperature in degrees Fahrenheit? A. 54.2°F B. 72.0°F C. 104.0°F D. 129.6°F

Last Answer : Answer: C

If a DC motor runs hot, the cause may be _____________. A. high mica condition B. low ambient temperature C. clogged ventilation ducts D. an open in the shunt field

Description : If a DC motor runs hot, the cause may be _____________. A. high mica condition B. low ambient temperature C. clogged ventilation ducts D. an open in the shunt field

Last Answer : Answer: C

Which of the listed conditions could indicate the need for cleaning electrical insulation? A. Low ambient temperature B. Low operating temperature C. High dielectric strength D. Low megger readings

Description : Which of the listed conditions could indicate the need for cleaning electrical insulation? A. Low ambient temperature B. Low operating temperature C. High dielectric strength D. Low megger readings

Last Answer : Answer: D

Magnetic controller contacts may become welded together during operating conditions as a result of _____________. A. high spring pressure B. high ambient temperature C. an open coil D. low voltage on operating coil

Description : Magnetic controller contacts may become welded together during operating conditions as a result of _____________. A. high spring pressure B. high ambient temperature C. an open coil D. low voltage on operating coil

Last Answer : Answer: D

Magnetic controller contacts may become welded together during operation because of _____________. A. excessive magnetic gap B. low contact pressure C. an open coil D. excessive ambient temperature

Description : Magnetic controller contacts may become welded together during operation because of _____________. A. excessive magnetic gap B. low contact pressure C. an open coil D. excessive ambient temperature

Last Answer : Answer: B

When troubleshooting a magnetic controller, it is found that the contacts are welded together. The most probable cause is _____________. A. excessive operation at low load B. high ambient temperature C. low voltage on the operating coil D. high voltage on the operating coil

Description : When troubleshooting a magnetic controller, it is found that the contacts are welded together. The most probable cause is _____________. A. excessive operation at low load B. high ambient temperature C. low voltage on the operating coil D. high voltage on the operating coil

Last Answer : Answer: C

Magnetic controller contacts may become welded together during operation due to _____________. A. an open coil B. low contact pressure C. excessive ambient temperature D. excessive magnetic gap

Description : Magnetic controller contacts may become welded together during operation due to _____________. A. an open coil B. low contact pressure C. excessive ambient temperature D. excessive magnetic gap

Last Answer : Answer: B

Electric strip heaters are used in motor controllers to _____________. A. prevent freezing of movable contacts B. keep the components at their design ambient temperature C. prevent condensation of moisture D. minimize resistance in internal circuits

Description : Electric strip heaters are used in motor controllers to _____________. A. prevent freezing of movable contacts B. keep the components at their design ambient temperature C. prevent condensation of moisture D. minimize resistance in internal circuits

Last Answer : Answer: C