Description : The nature of .fuse wire is – (1) high resistance and low melting point. (2) high resistance and high melting point. (3) low resistance and high melting point. (4) low resistance and low melting point.
Last Answer : (1) high resistance and low melting point. Explanation: A fuse or fusable link works by opening an electrical circuit when the current becomes too high. As the current increases, the temperature ... be connected in series with the appliance. Besides, it should have a comparatively high resistance.
Description : A Fuse wire is characterized by – (1) High resistance and low melting point (2) High resistance and high melting point (3) Low resistance and high melting point (4) Low resistance and low melting point
Last Answer : (4) Low resistance and low melting point Explanation: A fuse is a type of low resistance resistor that acts as a sacrificial device to provide over current protection, of either the load or source ... melt if a current more than the safe current for the appliance starts flowing through the circuit.
Description : A Fuse wire is characterised by (1) High resistance and low melting point (2) High resistance and high melting point (3) Low resistance and high melting point (4) Low resistance and low melting point
Last Answer : Low resistance and low melting point
Description : Safety fuse wire used in domestic electrical appliances is made of metal of low (1) Resistance (2) Melting point (3) Specific gravity (4) Conductance
Last Answer : (2) Melting point Explanation: The fuse wire is based on the Joules law of heating which says that when the electric current is allowed to pass through a conductor, the conductor heats up and is ... . For this purpose the material used as fuse wire should have high resistance and low melting point.
Last Answer : Melting point
Description : The material used for a fuse wire should have (a) high resistivity (b) high ductility (c) high melting point (d) low melting point
Last Answer : Ans:(d)
Description : The melting point of fuse wire should be high or low?
Last Answer : low
Description : The material used for fuse must have (a) low melting point and high specific resistance (b) low melting point and -low specific resistance (c) high melting point and low specific resistance (d) low melting point and any specific resistance
Last Answer : (a) low melting point and high specific resistance
Description : Nichrome wire is used in an electric heater because _______. (1) It has high resistance (2) It has high melting point (3) It can resist a current upto approx 5 amperes (4) For all of the above reasons
Last Answer : (4) For all of the above reasons
Description : For photoelectric effect to take place, the metal used as the cathode should have – (1) high melting point (2) low melting point (3) low work function (4) low resistance
Last Answer : (3) low work function Explanation: The photoelectric effect is the propensity of high-energy electromagnetic radiation to eject electrons from a given material. The photoelectric effect has been utilized in devices called photocells, consisting of two electrodes in a sealed vacuum tube.
Description : For photoelectric effect to take place, the metal used as the cathode should have______ (1) high melting point (2) low melting point (3) low work function (4) low resistance
Last Answer : low work function
Description : Which of the following low melting alloy containing bismuth and lead is used for electric fuse? (A) Wood's metal (B) Babbitt metal (C) Monel metal (D) Duralumin
Last Answer : Option A
Description : An instantaneous-trip-type fuse will _____________. A. open as soon as the load current exceeds its set point B. allow a preset delay between overcurrent and melting C. open a circuit by using a time delay element with a magnetic trip D. reset itself when the overcurrent is corrected
Last Answer : Answer: A
Description : Since fuse elements are made of zinc or any alloy of tin and lead, the melting point of the fuse element must be _____________. A. higher than that of copper B. lower than that of copper C. equal to that of copper D. reached when the conductor it is protecting becomes 'white hot.'
Last Answer : Answer: B
Description : Why is it a poor practice to use a high wattage soldering iron when soldering or desoldering components on a printed circuit board? A. The circuit board will blister and warp. B. The foil wire bonded ... board has a low melting temperature. D. The solder is kept to a dull heat dissipating finish.
Description : Fuse wire is made of an alloy of – (1) Tin and Lead (2) Tin and Copper (3) Lead and Copper (4) Copper and Silver
Last Answer : (1) Tin and Lead Explanation: The common material used as fuse wire is an alloy of tin and lead (63% tin and 37% lead). Fuse wires provide over current protection of an electrical circuit ... wire or strip that melts when too much current flows through it, thereby interrupting the flow of current.
Description : A fuse wire is made of: (1) an alloy of tin and copper (2) an alloy of tin and lead (3) an alloy of tin and aluminium (4) an alloy of nickel and chromium
Last Answer : (2) an alloy of tin and lead Explanation: Electric fuse wire is an alloy made of tin (63 % lead 37 %. The cross sectional area determines the melting point at a certain current. Alloys (e.g. ... resulting combination of good conductivity (due to the tin) with a low melting point due to the lead).
Description : The earth-wire of a cable is connected to – (1) the outer metallic body of the appliance (2) the fuse of the appliance (3) the filament of the appliance (4) short circuitry of the appliance
Last Answer : (2) the fuse of the appliance Explanation: Earth wire prevents Electric shocks. It is connected to the electrical cable of an appliance to prevent electric shocks. Actually it has very low resistance and allows current to pass through it easily.
Description : Fuse wire is made of an alloy of (1) Tin and Lead (2) Tin and Copper (3) Lead and Copper (4) Copper and Silver
Last Answer : Tin and Lead
Last Answer : an alloy of tin and lead
Description : The earth-wire of a cable is connected to (1) the outer metallic body of the appliance (2) the fuse of the appliance (3) the filament of the appliance (4) short circuitry of the appliance
Last Answer : the fuse of the appliance
Description : Refractory metals are known for which of the following properties: w) lack of chemical reactivity x) low density y) high melting point z) high thermal conductivity
Last Answer : ANSWER: Y -- HIGH MELTING POINT
Description : The fuse in our domestic electric circuit melts when there is a high rise in – (1) Inductance (2) Current (3) Resistance (4) Capacitance
Last Answer : (2) Current Explanation: In electronics and electrical engineering, a fuse is a type of low resistance resistor that acts as a sacrificial device to provide over protection, of either the load ... fuse interrupts excessive current (blows) so that further damage by overheating or fire is prevented.
Description : The filament of an electric lamp becomes white hot but the lead-in wires holding the filament are only slightly heated because they (a) have smaller current passing through them (b) have very low resistance (c) have higher melting point (d) are made of black iron
Last Answer : Ans:(b)
Description : What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage
Last Answer : Ans:(a)
Description : Ceramic nuclear metals compared to solid nuclear metals have (A) Higher melting points (B) Low strength at high temperature (C) More chances of radiation damage (D) Poorer corrosion resistance
Last Answer : (A) Higher melting points
Description : In addition to short circuits and sustained overloads, fuses are likely to blow due to _____________. A. loose fuse clips B. low ambient temperatures C. low contact resistance D. all of the above
Description : A fuse will blow for all the listed reasons EXCEPT ________. A. excessive vibration B. extremely hot surroundings C. loose fuse clips D. low contact resistance within the fuse
Last Answer : Answer: D
Description : A bird sitting on a high tension electric wire does not get electrocuted because – (1) it has high resistance (2) the body is earthed (3) it does not form a closed path for the flow of current (4) its feet are good insulators
Last Answer : (3) it does not form a closed path for the flow of current Explanation: Electricity travels from a place of high voltage to low voltage, just as water travels from high elevation to low ... When electricity travels through a body in this fashion, electrocution takes place, and the bird can die.
Description : A bird sitting on a high tension electric wire does not get electrocuted because (1) it has high resistance (2) the body is earthed (3) it does not form a closed path for the flow of current (4) its feet are good insulators
Last Answer : it does not form a closed path for the flow of current
Description : Metals are good conductors of electricity because - (1) they contain free electrons (2) the atoms are lightly packed (3) they have high melting point (4) All of the above
Last Answer : (1) they contain free electrons Explanation: Copper is used for electrical wiring because it is a good conductor of electricity. Metal particles are held together by strong metallic bonds, which is why they have high melting and boiling points.
Description : Tungsten is used for the manufacture of the filament of an electric bulb, because – (1) It is a good conductor (2) It is economical (3) It is malleable (4) It has a very high melting point
Last Answer : (4) It has a very high melting point Explanation: Tungsten is used because it has the highest melting point of all the metallic elements. It melts at 3410 degrees Celsius. When current passes ... bulb. The first successful light bulb filaments were made of carbon (from carbonized paper or bamboo).
Description : Metals are good conductors of electricity because – (1) they contain free electrons (2) the atoms are lightly packed (3) they have high melting point (4) All of the above
Description : Tungsten is used for the manufacture of the filament of an electric bulb, because (1) It is a good conductor (2) It is economical (3) It is malleable (4) It has a very high melting point
Last Answer : It has a very high melting point
Description : State difference between the wire used in the element of an electric heater and in a fuse wire. -Science
Last Answer : The wire used in the element of electric heater has a high resistivity and have a high melting point, so that even at a high temperature element do not burn while fuse wire have a low melting point and high resistivity so that it will melt if a current of large magnitude passes through the wire.
Description : Which covalent fuse wire is connected to the main circuit ?
Last Answer : The fuse wire is connected to the main circuit in a class co-op.
Description : Which wire is the fuse connected to ?
Last Answer : The fuse is connected to the live wire.
Description : To which wire is the fuse connected ?
Last Answer : The fuse is connected to the live wire
Description : What is immeterial for an electric fuse wire ?
Last Answer : What is immeterial for an electric fuse wire ? A. Its specific resistance B. Its radius C. Its length D. Current flowing through it
Description : How much current can flow through a piece if fuse wire before it melts?
Last Answer : What is the answer ?
Description : Fuse wire is made of an alloy of
Description : A fuse wire is made of:
Last Answer : An alloy of tin and lead
Description : Fuse wire is made of _____? A. 63% lead arid 37% tin B. 63% tin and 37% aluminum C. 63% tin and 37% lead D. 63% lead and 37% aluminum
Last Answer : ANSWER: C
Description : If a fuse blows frequently, one should (a) replace it with a thin wire (b) replace it with a thick copper wire (c) replace it with a paper clip (d) call an electrician
Description : In an electrical circuit, a fuse is connected (a) in the live wire (b) in the neutral wire (c) in the earth wire (d) anywhere—it makes no difference
Description : The commonly used safety fuse-wire is made of - (1) an alloy of Nickel and Lead (2) an alloy of Tin and Lead (3) an alloy of Tin and Nickel (4) an alloy of Lead and Iron
Last Answer : (2) an alloy of Tin and Lead Explanation: As a rule, fuse elements of time delay fuses contain low melting point materials, e.g. tin (Sn) or zinc (Zn) and alloys thereof.
Description : Fuse wire is made of an alloy of ______. (1) Lead and Copper (2) Tin and Copper (3) Tin and Lead (4) Copper and Silver
Last Answer : (3) Tin and Lead Explanation: The material used for making fuse element has a low melting point such as tin, lead, or zinc.
Description : A fuse wire can be indentify due to the properties
Last Answer : High Resistivity and minimum melting point
Description : Fuse wire is made of-------? A. 63% tin and 37% lead (Answer) B. 63% lead and 37% tin C. 63% tin and 37% aluminum D. 63% lead and 37% aluminum
Last Answer : A. 63% tin and 37% lead (Answer)