How can yoy change Mcpherson struts, would I need a spring compressor?

How can yoy change Mcpherson struts, would I need a spring compressor?
by

1 Answer

Answer :

You will need a spring compressor for any strut installation job.
by

Related questions

TIES : STRUTS : a.purlins : piers b.angle : tee c.rolle support : hinge d.compression : tension e.107 dynes

Description : TIES : STRUTS : a.purlins : piers b.angle : tee c.rolle support : hinge d.compression : tension e.107 dynes

Last Answer : d. compression : tension

He's a boastful, puffed-up fellow, wearing spurs; eyes gleaming yellow. As he proudly struts about, he's in charge, there is no doubt.What is he? -Riddles

Description : He's a boastful, puffed-up fellow, wearing spurs; eyes gleaming yellow. As he proudly struts about, he's in charge, there is no doubt.What is he? -Riddles

Last Answer : He is a Rooster.

instructions remove/install rear struts

Description : instructions remove/install rear struts

Last Answer : Need Answer

Shocks and Struts Replacement?

Description : Shocks and Struts Replacement?

Last Answer : form_title=Shocks and Struts Replacement form_header=Getting your shocks and struts replaced will restore vehicle handling and control while greatly improving ride comfort. What is the year, make and model of your ... on your car?=_ When was the last time your shocks and struts were replaced?=_

How do you replace the rear struts on a kia spectra?

Description : How do you replace the rear struts on a kia spectra?

Last Answer : With tools.

Struts are load carrying members of a frame structure which are subjected to (A) Axial tension loads (B) Axial compressive loads (C) Torsional loads (D) Transverse loads

Description : Struts are load carrying members of a frame structure which are subjected to  (A) Axial tension loads  (B) Axial compressive loads  (C) Torsional loads  (D) Transverse loads 

Last Answer : (B) Axial compressive loads 

Mild steel is used for (A) Structural works in beams, joints and girders (B) Small sized water pipes (C) Columns and struts (D) None of these

Description : Mild steel is used for (A) Structural works in beams, joints and girders (B) Small sized water pipes (C) Columns and struts (D) None of these

Last Answer : Answer: Option A

Cast iron is used for (A) Structural works in beams (B) Small sized water pipes (C) Columns and struts (D) None to these

Description : Cast iron is used for (A) Structural works in beams (B) Small sized water pipes (C) Columns and struts (D) None to these

Last Answer : Answer: Option C

Wrought iron is used for (A) Structural works in beams (B) Small sized water pipes (C) Columns and struts (D) None to these

Description : Wrought iron is used for (A) Structural works in beams (B) Small sized water pipes (C) Columns and struts (D) None to these

Last Answer : Answer: Option B

The members which support covering material of a sloping roof, are (A) Rafters (B) Purlins (C) Battens (D) Struts

Description : The members which support covering material of a sloping roof, are (A) Rafters (B) Purlins (C) Battens (D) Struts

Last Answer : Answer: Option A

A hand pump is usually fitted: a. For ground servicing purposes b. Lowering the landing gear in an emergency c. Pressurising the oleo struts in the air d. Retracting the gear after take-off

Description : A hand pump is usually fitted: a. For ground servicing purposes b. Lowering the landing gear in an emergency c. Pressurising the oleo struts in the air d. Retracting the gear after take-off

Last Answer : a. For ground servicing purposes

A hand pump is usually fitted: a. For ground servicing purposes b. Lowering the landing gear in an emergency c. Pressurising the oleo struts in the air d. Retracting the gear after take-off

Description : A hand pump is usually fitted: a. For ground servicing purposes b. Lowering the landing gear in an emergency c. Pressurising the oleo struts in the air d. Retracting the gear after take-off

Last Answer : a. For ground servicing purposes

Reciprocating compressor are provided with A. Simple disc/plate valve B. Poppet valve C. Spring-loaded disc valve D. Solenoid valve.

Description : Reciprocating compressor are provided with A. Simple disc/plate valve B. Poppet valve C. Spring-loaded disc valve D. Solenoid valve.

Last Answer : ANSWER : A

Which one of the following statements are correct for reciprocating air compressor? A. Its volumetric efficiency increases with increasing clearance ratio B. Its volumetric efficiency increases with pressure ratio C. Its volumetric efficiency does not vary with change in clearance ratio and pressure ratio D. Its volumetric efficiency decreases with increasing clearance ratio and pressure ratio

Description : Which one of the following statements are correct for reciprocating air compressor? A. Its volumetric efficiency increases with increasing clearance ratio B. Its volumetric efficiency increases ... ratio D. Its volumetric efficiency decreases with increasing clearance ratio and pressure ratio

Last Answer : ANSWER : D

Horsepower increase of a centrifugal gas compressor without altering the volumetric flow rate will __________ the gas discharge pressure. (A) Increase (B) Decrease (C) Not change (D) Exponentially decrease

Description : Horsepower increase of a centrifugal gas compressor without altering the volumetric flow rate will __________ the gas discharge pressure. (A) Increase (B) Decrease (C) Not change (D) Exponentially decrease

Last Answer : (A) Increase

The volumetric efficiency of the compressor ______ with the increase in altitude of place a) increases b) decreases c) does not change d) None

Description : The volumetric efficiency of the compressor ______ with the increase in altitude of place a) increases b) decreases c) does not change d) None

Last Answer : b) decreases

How Much Air Will I Need To Power My Air Compressor Tool?

Description : How Much Air Will I Need To Power My Air Compressor Tool?

Last Answer : Generally, most air tools will take around 70-100 PSI, and will consume less than 10 CFM, however consult the manual or manufacturer of your tool for exact air requirements.

Is Amp Draw Of The Compressor Something I Need To Be Concerned With?

Description : Is Amp Draw Of The Compressor Something I Need To Be Concerned With?

Last Answer : Yes, the lower the amp draw, the better the compressor is. As a rule of thumb, the maximum amperage that a compressor should require is 30amps.