Struts are load carrying members of a frame structure which are subjected to
(A) Axial tension loads
(B) Axial compressive loads
(C) Torsional loads
(D) Transverse loads
Description : Ties are load carrying members of a frame, which are subjected to (A) Transverse loads (B) Axial tension loads (C) Axial compressive loads (D) Torsional loads
Last Answer : (B) Axial tension loads
Description : A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular
Last Answer : b) Transverse loads and couples
Description : The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending ... at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.
Last Answer : (d) Compressive strength based on slenderness ratio and gross cross-sectional area.
Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (D) Torsional shear stress
Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Description : A long vertical member, subjected to an axial compressive load, is called (A) A column (B) A strut (C) A tie (D) A stanchion
Last Answer : (A) A column
Description : The base of a column is subjected to moment. If the intensity of bearing pressure due to axial load is equal to stress due to moment, then the bearing pressure between the base and the concrete ... Tension at one end and compression at the other end (d) Compression, verying as a parabolic profile
Last Answer : (b) Zero at one end and compression at the other end
Description : Cotter joint is employed when the members are subjected to which sort of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the above
Last Answer : c) Axial tensile or compressive
Description : Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned
Description : When loads are applied proportionately to a frame structure containing its members in one plane, the structure is called (A) Grid frame (B) Plane frame (C) Space frame (D) Truss frame
Last Answer : (C) Space frame
Description : During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above
Last Answer : C) Bending stresses
Description : During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above
Last Answer : c. Bending stresses
Description : The spokes of the flywheel are subjected to 1. direct shear stress 2. torsional shear stress 3. tensile stress 4. compressive stress
Last Answer : 3. tensile stress
Description : The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress
Last Answer : 1. direct tensile stress and bending stress
Description : The spokes of the flywheel are subjected to, (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (C) Tensile stress
Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (C) Bending stress
Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (A) Direct shear stress
Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Description : What is a mts frame axial torsional machine
Last Answer : Read about it here > http://www.mts.com/en/products/producttype/test-systems/load-frames-multiaxial/axial-torsional/index.htm
Description : When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress
Last Answer : B Bending stress
Description : When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress
Last Answer : (B) Bending stress
Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress
Last Answer : b) bending stress
Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) tensile stress c) compressive stress d) none of the mentioned
Last Answer : b) tensile stress
Description : The type of stress induced in a closed coiled helical tension spring is a. tensile b. compressive c. torsional shear d. tensile and compressive
Last Answer : c. torsional shear
Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive
Last Answer : (C) 26.67 kg/cm2 tensile
Description : A doubly reinforced section is used (a) When the members are subjected to alternate external loads and the bending moment in the sections reverses. (b) When the member are subjected to loading eccentric in ... . (c) When the members are subjected to accidental lateral loads . (d) All of the above
Last Answer : (d) All of the above
Description : A closely coiled helical spring of radius R, contains n turns and is subjected to an axial load W. If the radius of the coil wire is r and modulus of rigidity of the coil material is C, the deflection of the coil is (A) WR3n/Cr4 (B) 2WR3n/Cr4 (C) 3WR3n/Cr4 (D) 4WR3n/Cr
Last Answer : (D) 4WR3n/Cr
Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 ... 6 N/mm2 s = 12 N/mm2 (D) b = 5 N/mm2 s = 10 N/mm
Last Answer : (A) b = 10 N/mm2 s = 20 N/mm
Description : If a cohesive soil specimen is subjected to a vertical compressive load, the inclination of the cracks to the horizontal is (A) 90° (B) 45° (C) 22.5° (D) 0
Last Answer : (B) 45°
Description : In a spherical dome subjected to concentrated load at crown or uniformly distributed load, the meridional force is always (A) Zero (B) Tensile (C) Compressive (D) Tensile or compressive
Last Answer : (C) Compressive
Description : Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco ... (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above
Last Answer : (D) All the above
Description : If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) ... l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)
Last Answer : Answer: Option D
Description : The members which support covering material of a sloping roof, are (A) Rafters (B) Purlins (C) Battens (D) Struts
Last Answer : Answer: Option A
Description : When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the ... (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets
Last Answer : (c) Tacking rivets
Description : Buckling of a column occurs under (a) Axial load (b) Transverse load (c) Direct load (d) None
Last Answer : (a) Axial load
Description : Bending of beam occurs under (a) Axial load (b) Transverse load (c) Direct load (d) None
Last Answer : (b) Transverse load
Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity
Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity
Description : The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned
Last Answer : (c) both radial and axial loads
Description : Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load
Last Answer : C. Axial tensile or compressive load
Description : TIES : STRUTS : a.purlins : piers b.angle : tee c.rolle support : hinge d.compression : tension e.107 dynes
Last Answer : d. compression : tension
Description : What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data
Last Answer : c. 39.60 Mpa
Description : When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing
Last Answer : (c) Torsion
Description : Equivalent bending moment in a shaft subjected to axial load P, torque T and bending moment M is (a) Meq = 0.5 [M + (M2 + T2)0.5]0.5 (b) Meq = 0.5 [M + (M2 + T2)0.5] (c) Meq = ( M2 + T2)0.5 (d) None
Last Answer : (b) Meq = 0.5 [M + (M2 + T2)0.5]
Description : Equivalent torque in a shaft subjected to axial load P, torque T and bending moment M is (a) Teq = (Pa2 + M2 + T2) (b) Teq = (Pa2 + M2 + T2)0.5 (c)Teq = ( M2 + T2)0.5 (d) None
Last Answer : c)Teq = ( M2 + T2)0.5
Description : When a vertical member is carry by mainly axial loads, is called as (a) Strut (b) Column (c) Tie (d) All of these
Last Answer : (b) Column
Description : Pick up the correct statement from the following: (A) The roof slabs of multi-storeyed buildings are constructed monolithically to carry the various floor loads (B) The beams of multi-storeyed ... slab is spanned across the secondary beams provided between the main beams (D) All of these
Description : Pick up the correct statement from the following: (A) The moment of inertia is calculated about the axis about which bending takes place (B) If tensile stress is less than axial ... tensile stress is equal to axial stress, the section experiences compressive stress (D) All the above
Description : When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress