Describe ionosphere with neat sketch.

Describe ionosphere with neat sketch.
by

1 Answer

Answer :

image

The Ionosphere is the upper portion of the atmosphere. The ultra violet radiation from the sun will ionize the upper layer of the atmosphere. Due to ionization these part of the atmosphere becom3es electrically charged. In this layer free electrons and positive and negative ions are present and hence this layer of ions is known as ionosphere. There are four layers: D, E, F1 and F2.

1. D Layer:- It is lowest layer at an height of 70 kms with thickness 10 km.

The ionization density is maximum at noon and disappears at night.

2. E Layer:- It is the next layer at an height of 100 kms with thickness 25 km. The layer disappears at night due to recombination of ions and molecules.

3. F1Layer:- It is the next layer at an height of 180 kms with thickness 20 km. It provides more absorption for HF waves.

4. F2Layer:- It is the next layer at an height of 250-400 kms with thickness 200 km. It is having highest electron density of all layers, due to this F2 layer remains present at night time

 

by

Related questions

Describe the effect of ionosphere on sky wave propagation.

Description : Describe the effect of ionosphere on sky wave propagation.

Last Answer : The Ionosphere is the upper portion of the atmosphere. The ultra violet radiation from the sun will ionize the upper layer of the atmosphere. In this layer free electrons and positive and negative ions are ... layer. Its Frequency Range is from 3 MHz to 30 MHz Polarization: Vertical.  

Explain duct propagation with neat sketch.

Description : Explain duct propagation with neat sketch.

Last Answer : Duct propagation is a special type and used for very high microwave frequencies. New phenomenon which occurs in super-refraction, also known as ducting. As the height above earth increases, ... in the standard atmosphere. The Duct propagation is used for very high frequencies in GHz range.

Explain “BALUN” with neat sketch

Description : Explain “BALUN” with neat sketch

Last Answer : Diagram- Explaination

Explain virtual height with respect to wave propagation with neat sketch.

Description : Explain virtual height with respect to wave propagation with neat sketch.

Last Answer : In ionization layer the incident wave refracts and bends down gradually than sharply.   The incident and refracted rays follow paths that are exactly the same as they would have been if reflection had taken place from a surface located at a greater height called virtual height of this layer. 

Explain isotropic radiator with neat sketch.

Description : Explain isotropic radiator with neat sketch. 

Last Answer : An isotropic radiator is a point source that radiates equally in all the directions. It is a hypothetical antenna used as a reference to describe real antenna. The radiation is represented by a sphere with center coincides with location of isotropic radiator.

Explain ground wave propogation with neat sketch.

Description : Explain ground wave propogation with neat sketch. 

Last Answer : Sketch-   Explanationi) It consists of direct wave which travels near the ground from Transmitter to Receiver. ii) The electromagnetic wave leaves the transmitting antenna & remains close to earth surface ... . The ground wave is the path chosen when frequency in between 30 KHz & 3 MHz 

Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Description : Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Last Answer : Loop antenna:-The single turn coil carrying RF current through it having length less than the wavelength.   Advantages:- 1. highly directive 2. Small size Applications:- 1. For direction finding 2. In portable receivers 3. In navigation 

Define stub. Explain single and double stub in brief with neat sketch.

Description : Define stub. Explain single and double stub in brief with neat sketch.

Last Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching. 

Define and explain the term beam width related to antenna with a sketch.

Description : Define and explain the term beam width related to antenna with a sketch.

Last Answer : Definition: The beam width of an antenna is described as the angles created by comparing the half power point (3dB) on the main radiation lobe to its maximum power point. As an example the beam width ... max voltage at center of lobe (these point are known as half power points.) Sketch-  

Compare between simplex and full duplex communication on the basis of: 1) Definition 2) Sketch

Description : Compare between simplex and full duplex communication on the basis of: 1) Definition 2) Sketch

Last Answer : Compare between simplex and full duplex communication on the basis of: 1) Definition 2) Sketch

Explain with a neat diagram of ratio detector. Why limiter stage is not used before ratio detector.

Description : Explain with a neat diagram of ratio detector. Why limiter stage is not used before ratio detector.

Last Answer : With diode D2 reversed , O is positive with respect to b, so that Vab is a sum voltage rather than the difference it was in the discriminator it is now possible to connect a large capacitor ... of limiter stage due to large capacitor C5 .Hence, limiter stage is not used in ratio detector.  

With the help of neat diagram, explain the working of phase discriminator.

Description : With the help of neat diagram, explain the working of phase discriminator.

Last Answer : Explanation:- This discriminator is also known as the center tuned discriminator or the Foster Seeley discriminator after its inventors. It is possible to obtain the same S- Shape response curve from a circuit in ... fin = fc, fin > fc + Δf and fin<fc- Δf should be given marks

Explain effect of 'm' on AM with neat waveforms.

Description : Explain effect of 'm' on AM with neat waveforms.

Last Answer : i)m< 1  If m < 1 or if the percentage of modulation is less than 100% the this type of modulation is known as under modulation The amplitude of modulating signal less than carrier ... greater amplitude part of its information is lost in the process of modulation which is undesirable.

State the need of AGC. List the different types of AGC with neat graph.

Description : State the need of AGC. List the different types of AGC with neat graph.

Last Answer : Need of AGC:- The need or purpose of AGC circuit is to maintain the output voltage level (volume) of radio receiver constant over a wide range of RF input signal level.  AGC also helps to smooth out the rapid ... of AGC:- 1) Simple AGC 2) Delayed AGC Graphical representation of AGC:- 

Explain skip zone and skip distance with neat diagram.

Description : Explain skip zone and skip distance with neat diagram.

Last Answer : Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wav of fixed frequency returns back to the earth. Skip zone: skip zone where signal is not detectable

Explain ionospheric propagation with neat sketch. Explain two properties of layers of ionosphere.

Description : Explain ionospheric propagation with neat sketch. Explain two properties of layers of ionosphere.

Last Answer : Diagram :   Explanation: The transmitted signal travels into the upper atmosphere where it is reflected back to earth due to the presence of layers called as ionosphere in the upper ... having highest electron density of all layers, due to this F2 layer remains present at night time.

Describe the functions of mixer and local oscillator in radio receiver

Description : Describe the functions of mixer and local oscillator in radio receiver

Last Answer : Frequency Mixer:- The function of frequency mixer is to heterodyne signal frequency fs and local oscillator frequency fo. At the output, it produces the difference frequency known as ... local oscillator frequency fo is then mixed with incoming frequency to give intermediate frequency. 

Describe the block diagram of FM superhetrodyne receiver

Description : Describe the block diagram of FM superhetrodyne receiver

Last Answer : RF amplifier:- There are two important functions of RF amplifier: 1) To increase the strength of weak RF signal. 2) To reject image frequency signal. In FM broadcast the ... FM broadcast, the maximum modulating frequency is 15 kHz. Hence the audio amplifier must have large bandwidth.

Describe line of sight propagation in brief.

Description : Describe line of sight propagation in brief.

Last Answer : Line of sight propagation or Space wave propagation:-   Explanation:- Space wave propagation of electromagnetic energy includes radiated energy that travels in the lower few miles of Earth's ... waves reflected by Earth's surface as they propagate between the transmit and receive antennas. 

Describe the block diagram of basic communication system.

Description : Describe the block diagram of basic communication system.

Last Answer : Describe the block diagram of basic communication system.

Describe with respect to antenna (i) radiation pattern (ii) directive gain (iii) power gam (iv) polarization

Description : Describe with respect to antenna (i) radiation pattern (ii) directive gain (iii) power gam (iv) polarization

Last Answer : (i) Radiation pattern:-A graph or diagram which tells us about the manner in which an antenna radiates more power in different directions is known as the radiation patteren of antenna.  ( ... as the direction of the electric vector in the electromagnetic wave radiated by the transmitting antenna. 

Describe the term virtual height with the help of diagram showing ionized layer and the path of wave.

Description : Describe the term virtual height with the help of diagram showing ionized layer and the path of wave.

Last Answer : Virtual height: -The incident wave returns back to the earth due to refraction. In this process it bends down gradually and not sharply, but the incident and reflected rays follow exactly ... . It is also defined as the maximum height that the hypothetical reflected wave would have reached. 

Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Description : Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Last Answer : Antenna Resistance - The resistance of an antenna has two components: 1. Its radiation resistance due to conversion of power into electromagnetic waves 2. The resistance due to actual losses in the ... the transmitter power divided by the surface area of a sphere (4πR2) at that distance.

Draw practical set-up and explain the procedure to measure selectivity of radio receiver.

Description : Draw practical set-up and explain the procedure to measure selectivity of radio receiver.

Last Answer : Procedure to measure selectivity of radio receiver: Throughout the measurement the receiver is kept tuned to desired frequency 950 Khz. Now the generator output frequency is deviated below ... the generator output voltage is adjusted to get a standard 50 miliwatt receiver output power.

Draw and label the circuit diagram of ratio detector

Description : Draw and label the circuit diagram of ratio detector 

Last Answer : Draw and label the circuit diagram of ratio detector  

Draw the structure and state applications of: i) Ferrite loop (rod) antenna ii) Horn antenna

Description : Draw the structure and state applications of: i) Ferrite loop (rod) antenna ii) Horn antenna

Last Answer : Horn antenna: Application:- i) Used at microwave frequency. ii) Used in satellite tracking.  Ferrite loop antenna: Application:- In Am radio receiver to receive MW and SW band signals. In FM radio receiver

Calculate the characteristics impedance for a transmission line having L=0.5 mH/Km, C=0.08 µF and negligible R and G.

Description : Calculate the characteristics impedance for a transmission line having L=0.5 mH/Km, C=0.08 µF and negligible R and G.

Last Answer : L=0.5 mH/Km C=0.08 µF

State the need of stub. Explain single stub and double stub matching.

Description : State the need of stub. Explain single stub and double stub matching.

Last Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible. ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching.  

Explain the working of amplitude limiter in FM receiver with circuit diagram.

Description : Explain the working of amplitude limiter in FM receiver with circuit diagram.

Last Answer : Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy  Circuit Diagram:

A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Description : A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Last Answer : Given Intermediate Frequency fi=455KHz Signal frequency =fs=1000KHz Local oscillator frequency fo=fs+fi  Fo=1000KHz+455KHz  =1455KHz Image frequency is the input frequency which produces the same intermediate frequency fsi=fs+2fi  =1000KHz+2*455KHz  =1910KHz 

Draw circuit diagram of transistor reactance modulator. Explain its working.

Description : Draw circuit diagram of transistor reactance modulator. Explain its working.

Last Answer : Explanation- A reactance modulator is illustrated in figure. It is basically a standard commonemitter class A amplifier. Resistors R1 and R2 from a voltage divider to bias ... frequency, whereas a lower capacitance increases the frequency. The circuit produces direct frequency modulations.

State and explain the concept of transmission bandwidth.

Description : State and explain the concept of transmission bandwidth.

Last Answer : Bandwidth is defined as the portion of the electromagnetic spectrum occupied by a signal We may also define the bandwidth as the frequency range over which as information signal is transmitted. Bandwidth is the ... to 15 KHZ. Therefore the bandwidth is(f2-f1) BW= f2 - f1= 15000-20=14980Hz

Define critical frequency w.r. to wave propagation.

Description : Define critical frequency w.r. to wave propagation.

Last Answer : Define critical frequency w.r. to wave propagation.

Define VSWR with refernce to standing waves.

Description : Define VSWR with refernce to standing waves.

Last Answer : Voltage Standing Wave Ratio: The voltage standing wave ratio (VSWR) is the ratio of max voltage to min voltage. VSWR= VMAX /VMIN

State two disadvantages of TRF receiver over superheterodyne receiver.

Description : State two disadvantages of TRF receiver over superheterodyne receiver.

Last Answer : Disadvantages of TRF Receiver: 1. Instability due to oscillatory nature of RF amplifier. 2. Variation in bandwidth over tuning range. 3. Insufficient selectivity at high frequencies 4. Poor adjacent channel rejection capability 

Define sensitivity with graph.

Description : Define sensitivity with graph.

Last Answer : Define sensitivity with graph.

Explain operation of balanced slope detector with „s‟ curve.

Description : Explain operation of balanced slope detector with „s‟ curve.

Last Answer : Diagram: Explanation:   Curve:  

Draw block diagram of FM receiver and explain the use of limiter circuit.

Description : Draw block diagram of FM receiver and explain the use of limiter circuit.

Last Answer : Diagram Explanation Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy.

Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Description : Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Last Answer : Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Explain working of envelope detector with suitable diagram and waveform.

Description : Explain working of envelope detector with suitable diagram and waveform.

Last Answer : Envelope Detector: An Envelope Detector is an electronic circuit that takes a high frequency signal as input and provides an output which is as envelopes of the original signal. The capacitor ... decreases the responsiveness thus, real-world designs must be optimized for the application.

Draw construction of Yagi-Uda antenna and explain.

Description : Draw construction of Yagi-Uda antenna and explain.

Last Answer : Explanation A Yagi-Uda antenna, commonly known as a Yagi antenna, is a directional antenna consisting of multiple parallel elements in a line, usually half-wave dipoles made of ... receiver with a transmission line and additional parasitic elements called reflector and one or more directors.

A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Last Answer : Solution :

Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?

Description : Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?

Last Answer : Reason for LO frequency to be greater than signal frequency The local oscillator frequency (f0) is made greater than signal frequency (Fs) in radio receiver: Local oscillator frequency range is 995 ... frequency of desired signal because the IF is constant and same for all the incoming RF signal.

Draw waveform for standing waves on an open and shorted line. Prove that impedance is inverted at every quarter wavelength interval.

Description : Draw waveform for standing waves on an open and shorted line. Prove that impedance is inverted at every quarter wavelength interval.

Last Answer : Waveform- Explanation When the transmission line is short circuited voltage is zero and current is maximum.The variation is according to the wavelength. When the ... The pattern repeats for every half wavelength. Thus impedance is inverted at every quarter wavelength interval.

Write one application of following antenna i. Rectangular antenna ii. Dish antenna iii. Yagi-Uda antenna iv. Horn antenna

Description : Write one application of following antenna i. Rectangular antenna ii. Dish antenna iii. Yagi-Uda antenna iv. Horn antenna 

Last Answer : i. Rectangular antenna is used in direction finding in portable recievers. ii. Dish antenna is used to transmit and receive signal from satellite. iii. Yagi-Uda antenna is used in HF and VHF range as a TV receiving antenna. iv. Horn antenna is used in satellite tracking.

a) For a transmission line, Find SWR and reflection coefficient R if, i. There is no reflected voltage. ii. Reflected voltage and incident voltage is equal. iii. If reflected voltage=20V and incident voltage=10V. iv. If reflected voltage=10V and incident voltage =20V.

Description : a) For a transmission line, Find SWR and reflection coefficient R if, i. There is no reflected voltage. ii. Reflected voltage and incident voltage is equal. iii. If reflected voltage=20V and incident voltage=10V. iv. If reflected voltage=10V and incident voltage =20V.

Last Answer : reflection coefficient R=Vr/Vi i. There is no reflected voltage. i.e,Vr=0 R=0 SWR= 1+R/1-R=1 ii. Reflected voltage and incident voltage is equal. Vr=Vi; R=1 SWR= 1+R/1-R=1+1/1-1=infinity iii. If reflected ... and incident voltage =20V. Vr=10 and Vi=20 R=10/20=0.5 SWR= 1+R/1-R=1+.5/1-.5=3 

In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Description : In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Last Answer : Given deviation∆=75kHz i) fm=500Hz bandwidth B.W=2(∆+fm)  =2(75k+500)=151kHz  ii). fm=5KHz bandwidth B.W=2(∆+fm)  =2(75k+5k)=160KHz iii) fm=10KHz bandwidth B.W=2(∆+fm)  =2(75k+10k)=170KHz As the modulating frequency increases bandwidth also increases.

Define PAM, PWM, and PPM. Draw waveforms.

Description : Define PAM, PWM, and PPM. Draw waveforms.

Last Answer : Pulse amplitude modulation is defined as a process of varying the amplitude of the carrier pulse in accordance to the modulating signal variations. Pulse width modulation is defined as a ... of varying the position of the carrier pulse, in accordance to the modulating signal variations.

A telephone cable has following primary constants per loop kilometer ,R=30Ω, L=20mH,C=0.06µF,G=0.If the applied signal has an angular frequency of 5000 rad/sec.., Determine (i) Characteristics impedence (ii) Attenuation constant

Description : A telephone cable has following primary constants per loop kilometer ,R=30Ω, L=20mH,C=0.06µF,G=0.If the applied signal has an angular frequency of 5000 rad/sec.., Determine (i) Characteristics impedence (ii) Attenuation constant

Last Answer : A telephone cable has following primary constants per loop kilometer ,R=30Ω, L=20mH,C=0.06µF,G=0.If the applied signal has an angular frequency of 5000 rad/sec.., Determine (i) Characteristics impedence (ii) Attenuation constant

A super heterodyne AM receiver is tuned to a station operating at 1200 KHz .Find local oscillator frequency and image frequency.

Description : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz .Find local oscillator frequency and image frequency.

Last Answer : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz Intermediate frequency is 455KHz. IF frequency=f0-fs Local oscillator frequency is f0=IF +fs=455K+1200K=1655kHz The image frequency which gives the same IF is f0+2*IF=2110KHz