Part of the transformer which is most subject to damage from overheating is?

1 Answer

Answer :

Part of the transformer which is most subject to damage from overheating is winding insulation.

Related questions

Description : Which of the following is not a part of transformer installation?  (A) Conservator (B) Breather (C) Buchholz Relay (D) Exciter

Last Answer : Which of the following is not a part of transformer installation?  (A) Conservator (B) Breather (C) Buchholz Relay (D) Exciter

Description : What can I do about my Chevrolet 4.3 v6 engine overheating?

Last Answer : answer:Overheating problems are usually fairly easy to diagnose and I would think if your dad is the owner of a 100 year old truck, he knows how to spin a wrench. I would assume he either didnt ... usually ID that if there is fluid leaking from the heads or the rad fluid is spotty or milky.

Last Answer : Overheating of relay contacts or contact born out is due to slow making and breaking of load circuit contacts, foreign matter on the contact surface, too low contact pressure.

Description : How to Repair Water Damage

Last Answer : How to Repair Water Damage Our homes are our frontline protection against the elements. Over time, the wear and tear will begin to show, and some of them come in the form of water damage. ... now prime with more primer-sealer before letting dry completely. Re-paint the formerly water damaged area.

Description : How to Clean Water Damage to Carpet

Last Answer : How to Clean Water Damage to Carpet Carpets can make or break a room's overall look. While carpets are lovely additions to our home, they can stain easily and leave a very unsightly impression. Carpets ... with a utility knife. You can then attach a new piece from a remnant using a carpet adhesive.

Description : What is Part Programming? Enlist Basic Requirement for part programming with suitable example.

Last Answer : Definition: The part program is a sequence of instructions, which describe the work, which has to be done on a part, in the form required by a computer under the control of a numerical ... Defining the work part geometry. (b) Defining the repetition work. (c) Specifying the operation sequence

Last Answer : In Hopknison demand rate or two part tariff the demand rate or fixed charges are dependent upon the maximum demand of the consumer.

Last Answer : In two part tariff, variation in load factor will affect operating or running charges.

Description : Are you good at calculating, what would the effects be for these [details inside]?

Last Answer : answer:It depends on many things: What is the comet made of? What is its mass? Does it strike in one piece or break into several or many pieces at atmospheric contact? How fast is it approaching and at what angle?

Description : I'm not sure if my head gasket it blown but will adding sealant just to make sure hurt it in anyway?

Last Answer : Check the radiator; make sure that’s working. Check oil and antifreeze levels. Make sure there are no leaks. Check fans.

Description : Why would my 96 Ford Contour GL have no heat, and overheat after about 30 minutes?

Last Answer : If the heater core is blocked, you’re not getting the circulation you think you are, and nor have you bled the system, because there will still be trapped air. Can you rig a temp hose and bypass the heater core? (As opposed to taking the car to a dealer) and see if that’s the problem?

Description : The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by which part of the transformer?

Last Answer : The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by conservator.

Description : Explain the effect of Harmonics on the Transformer.

Last Answer : Effect of Harmonics on the Transformer:  1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations.  5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

Description : List two special feature of welding transformer.

Last Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

Description : State two applications of isolation transformer

Last Answer : Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.

Description : State why a transformer always have an efficiency of more than 90%.

Last Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.

Description : Equivalent circuit of transformer

Last Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

Description : Single phase transformer

Last Answer : Single phase Transformer Transformer

Description : What is the use of transformer?

Last Answer : The use of transformer  is to do lower or raise  the voltage or currents in an electrical  circuit.  That's quite so simple. 

Description : Write about transformer on DC.

Last Answer : Transformer on DC : Transformer cannot work on DC. Transformer works on electromagnetic induction principle. Electromagnetic induction principle means when flux linking with coil changes and EMF induced in it ... winding insulation will burn.

Description : State and justify which of the following two transformers is better:  Transformer A = 4% voltage regulation  Transformer B = 6% voltage regulation

Last Answer : Transformer A with 4% voltage regulation is better.  Justification: Voltage regulation refers to the percentage change in secondary voltage when load is changed from no-load to full-load with primary voltage ... 4% voltage regulation, which is less as compared to 6% of transformer B, it is better.

Description : State any four characteristics of core type transformer.

Last Answer : Characteristics of core type transformer: i) It has one window. ii) It has one magnetic circuit. iii) Core surrounds the winding. iv) Average length of core is more. v) Area of cross ... Better cooling for winding. vii) Mechnical strength is comparatively less. viii) Repair and maintenance is easy.

Description : Explain construction and working of single phase Auto transformer.

Last Answer : Construction of single phase auto transformer: (i) It has only one winding wound on a laminated circular magnetic core. (ii) The core is made of silicon steel stampings. (iii) The two terminals of the ... help of handle. 5) The same transformer can be used as step-up or step down auto-transformer

Last Answer : No-load current in a transformer lags behind the voltage by about 75°.

Last Answer : The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

Last Answer : In the transformer low voltage winding has got more cross-sectional area.

Last Answer : A transformer cannot raise or lower the voltage of a D.C. supply because Faraday's laws of electromagnetic induction are not valid since the rate of change of flux is zero.

Last Answer : Primary winding of a transformer could either be a low voltage or high voltage winding.

Last Answer : High voltage winding in a transformer has more number of turns.

Last Answer : The efficiency of a power transformer is of the order of 98 percent.

Last Answer : The no load current in a transformer lags behind the applied voltage by an angle of about 75°.

Last Answer : In a transformer, routine efficiency depends upon load current and power factor of load.

Last Answer : The maximum efficiency of a distribution transformer is at 50% full load.

Last Answer : Transformer breaths in when load on it decreases.

Last Answer : No-load current of a transformer has small magnitude and low power factor.

Last Answer : The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

Last Answer : The power transformer is a constant main flux device.

Last Answer : In a transformer, the tappings are generally provided on low voltage side.

Last Answer : The use of higher flux density in the transformer design reduces weight per kVA.

Last Answer : The chemical used in breather for transformer should have the quality of cleansing the transformer oil.

Last Answer : An ideal transformer has infinite values of primary and secondary inductances. The statement is false.

Last Answer : The transformer ratings are usually expressed in terms of kVA.

Last Answer : Material used for construction of transformer core is usually silicon steel.

Last Answer : The thickness of laminations used in a transformer is usually 0.4 mm to 0.5 mm.

Last Answer : conservator or a reservoir tank for insulating oil in transformer which used for balanced the onload oil level with help of oil level indicator which mount on middle part of reservoir tank.

Last Answer : A transformer oil must be free from moisture.

Last Answer : Gas is usually not liberated due to dissociation of transformer oil unless the oil temperature exceeds 150°C.

Last Answer : The main reason for generation of harmonics in a transformer could be saturation of core.

Last Answer : Delta/star transformer works satisfactorily when on balanced as well as unbalanced loads.

Last Answer : The magnetising current of a transformer is usually small because it has small air gap.