Description : Pick out the wrong statement. (A) A slight haze at the top of chimney indicates good combustion in the furnace (B) A bag filter incurs very small pressure drop and is very efficient for ... dust collection equipment for removal of submicronic dust particles present in flue gas (D) None of these
Last Answer : (B) A bag filter incurs very small pressure drop and is very efficient for removal of submicronic dust particles from flue gases at very high temperature
Description : The percentage increase in power consumption of a compressor with suction side air filter and with the pressure drop across the filter of 200 mmWc is ____ a) 1.0% b) 3% c) 2.4% d) 1.6%
Last Answer : d) 1.6%
Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. insure that the voltage across the governor coil (EG-3P) never exceeds .6 VDC B. compensate for the ... heating up C. protect the electronic governor from counter EMF D. act as a filter to prevent hunting
Last Answer : Answer: C
Description : Filter aid is used to (A) Increase the rate of filtration (B) Decrease the pressure drop (C) Increase the porosity of the cake (D) Act as a support base for the septum
Last Answer : (C) Increase the porosity of the cake
Description : Bag filter design is predominantly dependent on gas temperature, as it affects the gas density & viscosity and the selection of filtering material. The pressure drop in a bag filter is (A) Inversely proportional to ... the gas (C) Proportional to the pressure of the gas (D) Both (B) and (C)
Last Answer : (D) Both (B) and (C)
Description : What is the pressure drop across an air intake system?
Last Answer : Look up venturi and fluid dynamics on a search engine.
Description : With increase in the pressure drop across the cake, the specific cake resistance for the compressible sludge (A) Increases (B) Decreases (C) Remains constant (D) Increases linearly
Last Answer : (A) Increases
Description : Pick out the wrong statement. (A) Heat transfer by radiation cannot occur across an absolute volume (B) In case of a shell and tube heat exchanger, the pressure drop through the shell is ... The amount of heat involved in the condensation or vaporisation of 1 kg of a fluid is the same
Last Answer : (A) Heat transfer by radiation cannot occur across an absolute volume
Description : The actual temperature drop across the heating surface in an evaporator depends on the (A) Feed (B) Depth of liquid over heating surface (C) Pressure difference between steam chest and vapour space (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : The actual temperature drop across the heating surface of an evaporator depends on the (A) Liquid depth over the heating surface (B) Solution being evaporated (C) Pressure difference between the steam chest and the vapor space above the boiling liquid (D) All (A), (B) and (C)
Description : For flow of fluids through packed bed, the superficial velocity is (A) Less than the average velocity through channels (B) More than the average velocity through channels (C) Dependent on the pressure drop across the bed (D) Same as the average velocity through channels
Last Answer : (A) Less than the average velocity through channels
Description : . A 0.5 m high bed made up of a 1 mm dia glass sphere (density 2500 kg/m3 ) is to be fluidised by water (density 1000 kg/m3 ). If at the point of incipient fluidisation, the bed voidage is 40%, the pressure drop across the bed is (A) 4.4 KPa (B) 2.94 KPa (C) 3.7 KPa (D) None of these
Last Answer : (A) 4.4 KPa
Description : Applying a pressure drop across a capillary results in a volumetric flow rate 'Q' under laminar flow conditions. The flow rate for the same pressure drop, in a capillary of the same length but half the radius is (A) Q/2 (B) Q/4 (C) Q/8 (D) Q/16
Last Answer : (D) Q/16
Description : A 2" gate valve fitted in a pipe is replaced by a similar globe valve. Pressure drop in gate valve was Δp. For the same discharge, the pressure drop across globe valve is (A) Δp (B) < Δp (C) > Δp (D) Δp
Last Answer : (C) > Δp
Description : Are there any alternatives to scraping a shell and tube if a capacity increase will make the pressure drop across the exchanger too large?
Last Answer : When an increase in capacity will cause excessive pressure drop, you may not have to junk the heat exchangers. A relatively inexpensive alteration is to reduce the number of tube passes. ... the exchangers in parallel or using lowfins or other special tubing. Source: Gulley Computer Associates
Description : Permanent loss in a Venturimeter is about __________ percent of the pressure drop in the upstream cone. (A) 1 (B) 10 (C) 40 (D) 70
Last Answer : (B) 10
Description : The horizontal line which cuts across 'L1' shown in figure 'A' of the illustration indicates a/an ______________. EL-0091 A. iron core B. saturable core C. air gap D. capacitive coupling
Last Answer : Answer: B
Description : A few drops of sap were collected by cutting across a plant stem by a suitable method. The sap was tested chemically. Which one of the following test results indicates that it is phloem sap? (a) Acidic (b) Alkaline (c) Low refractive index (d) Absence of sugar
Last Answer : (b) Alkaline
Description : Fuel oil is subjected to visbreaking to reduce its (A) Pour point (B) Viscosity (C) Pressure drop on pumping (D) All (A), (B) and (C
Last Answer : (D) All (A), (B) and (C
Description : Pitch (a product of coal tar distillation) is always mixed with creosote oil, when it is to be burnt in a burner, because (A) Its calorific value is very less (B) Tar neutralises the residual acids ... for its transportation through pipelines at economic pressure drop (D) All (A), (B) and (C)
Last Answer : (C) It reduces viscosity and imparts fluidity for its transportation through pipelines at economic pressure drop
Description : In Fraunhofer diffraction pattern for single slit, a central maximum is obtained when angle of diffraction q is equal to zero. What it actually indicates? A. All the diffracted rays are parallel and focused ... are diffracted by the slit in all the directions D. The rays are reflected by the slit
Last Answer : A. All the diffracted rays are parallel and focused by slit at a single point on screen
Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting
Last Answer : Answer: A
Description : Would window/door screen material work to filter particles out of grease?
Last Answer : I’d think cheesecloth is the way to go. Unless maybe you could line up several layers of screening, with the holes slightly offset.
Description : Is a coffee filter required for a coffee machine that has a plastic screen?
Last Answer : A coffee filter is generally not required for a coffee machine which already has a plastic screen. The plastic screen serves as the built-in filter system for the coffee machine. The most important thing ... are not leftover. This will also guarantee you a fresh and smooth cup of coffee each time.
Description : A 24 volt battery supplies three devices wired in parallel that each have a resistance of 9 ohms. What is the voltage drop across each device?
Last Answer : A simple circuit has three resistors connected in series. The resistors are 14 ohms 12 ohms and 9 ohms. What is the total resistance of the circuit?
Description : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the polarity as indicated. The ratio of potential difference acro
Last Answer : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the ... difference across `5Omega` and resistance `R` is
Description : Determine the voltage drop across the resistance `R_(1)` in the circuit given in Fig. 4.55 with `epsilon=90 V, R_(1)=5 k Omega, R_(2)=5k Omega, R_(3)=
Last Answer : Determine the voltage drop across the resistance `R_(1)` in the circuit given in Fig. 4.55 with `epsilon=90 V, ... k Omega " and " R_(4)=10 k Omega`.
Description : Consider the diagram shown below. A Voltmeter of resistance `150 Omega` is connected across A and B. The potential drop across B and C measured by vol
Last Answer : Consider the diagram shown below. A Voltmeter of resistance `150 Omega` is connected across A and B. The potential ... 29 B. 27 V C. 31 V D. 30 V
Description : The potential drop across the `3 Omega` resistor is
Last Answer : The potential drop across the `3 Omega` resistor is A. 1 V B. `1.5 V` C. 2 V D. 3 V
Description : How are the voltage drop across R and XL related in series RL circuit?
Last Answer : Voltage drop across a circuit is IZ, where I is current and Z isimpedance. In other words IZ = IR + jIX, where R is resistance andX is inductance
Description : As shown in the illustration, if 'R1' and 'R2' have unequal values, the ____________. EL-0019 A. voltage drop across 'R1' will not be equal to the voltage drop across 'R2' B. current flow ... energy dissipated in 'R2' D. current flow through 'R1' will differ from the current flow through 'R2'
Last Answer : Answer: D
Description : A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across ... using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter
Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts
Description : In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC
Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Description : What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Description : In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit
Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.
Description : In a DC series circuit, all the conductors have the same ____________. A. power expended in them B. voltage drop across them C. resistance to current flow D. current passing through them
Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω
Last Answer : 500Ω
Description : A composite flat wall of a furnace is made of two materials 'A' and 'B'. The thermal conductivity of 'A' is twice of that of material 'B', while the thickness of layer of 'A' is half that of B. If the temperature ... drop (in °K) across the layer of material 'A' is (A) 125 (B) 133 (C) 150 (D) 160
Last Answer : (D) 160
Description : In case of a multipass shell and tube heat exchanger, the temperature drop in the fluid (A) Is inversely proportional to the resistance across which the drop occurs (B) And the wall are proportional to individual resistances (C) And the wall is not related (D) None of these
Last Answer : (B) And the wall are proportional to individual resistances
Description : In a shell and tube heat exchanger, (A) The temperature drops in the two fluids and the wall are proportional to individual resistances (B) The temperature drop is inversely proportional to ... ) There is no relationship between temperature drop and resistance (D) The relationship is not generalised
Last Answer : (A) The temperature drops in the two fluids and the wall are proportional to individual resistances
Description : What is the name of a headline which very large composed of one or more lines and usually extending across a page or almost the full width of a page? a) Banner Headline b) Drop Headline c) Label Headline d) Blanket Headline
Last Answer : a) Banner Headline
Description : the voltage drop across RS and R1 determines the amount of base-emitter ____ for Q1.
Last Answer : Bias.
Description : how is (a) the current through R2 and (b) the voltage drop across R2 computed?
Last Answer : (a) By adding the bleeder current (IR1) and the current through load 1(b) By subtracting the voltage of load 1 from the voltage of load 2.
Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?
Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts
Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?
Last Answer : Zero.
Description : Three resistors which have different values are connected in series. Which one of the following statements is correct? w) The potential drop across all three resistors is the same. x) The same current passes through all three resistors. y) The same power is dissipated by all three resistors.
Last Answer : ANSWER: X -- THE SAME CURRENT PASSES THROUGH ALL THREE RESISTORS.
Description : A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)
Last Answer : ANSWER: Z -- 5 V/R