Applying a pressure drop across a capillary results in a volumetric flow rate 'Q' under laminar flow conditions. The flow rate for the same pressure drop, in a capillary of the same length but half the radius is (A) Q/2 (B) Q/4 (C) Q/8 (D) Q/16

Applying a pressure drop across a capillary results in a volumetric flow
rate 'Q' under laminar flow conditions. The flow rate for the same pressure
drop, in a capillary of the same length but half the radius is
(A) Q/2
(B) Q/4
(C) Q/8
(D) Q/16
by

1 Answer

Answer :

(D) Q/16
by

Related questions

For laminar flow of a shear thinning liquid in a pipe, if the volumetric flow rate is doubled, the pressure gradient will increase by a factor of (A) 2 (B) < 2 (C) > 2 (D) 1/2

Description : For laminar flow of a shear thinning liquid in a pipe, if the volumetric flow rate is doubled, the pressure gradient will increase by a factor of (A) 2 (B) < 2 (C) > 2 (D) 1/2

Last Answer : (A) 2

Discharge in laminar flow through a pipe varies (A) As the square of the radius (B) Inversely as the pressure drop (C) Inversely as the viscosity (D) As the square of the diameter

Description : Discharge in laminar flow through a pipe varies (A) As the square of the radius (B) Inversely as the pressure drop (C) Inversely as the viscosity (D) As the square of the diameter

Last Answer : (A) As the square of the radius

In laminar flow through a round tube, the discharge varies (A) Linearly as the viscosity (B) Inversely as the pressure drop (C) Inversely as the viscosity (D) As the square of the radius

Description : In laminar flow through a round tube, the discharge varies (A) Linearly as the viscosity (B) Inversely as the pressure drop (C) Inversely as the viscosity (D) As the square of the radius

Last Answer : (C) Inversely as the viscosity

. If a single tube pass heat exchanger is converted to two pass, then for the same flow rate, the pressure drop per unit length in tube side will (A) Increase by 1.8 times (B) Decrease by 2 2 (C) Increase by 2 16 (D) Remain unchanged

Description : . If a single tube pass heat exchanger is converted to two pass, then for the same flow rate, the pressure drop per unit length in tube side will (A) Increase by 1.8 times (B) Decrease by 2 2 (C) Increase by 2 16 (D) Remain unchanged

Last Answer : (C) Increase by 2 16

For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Description : For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Last Answer : (B) 1/μ

For laminar flow of a fluid through a packed bed of spheres of diameter d, the pressure drop per unit length of bed depends upon the sphere diameter as (A) d (B) d 2 (C) d 4 (D) d

Description : For laminar flow of a fluid through a packed bed of spheres of diameter d, the pressure drop per unit length of bed depends upon the sphere diameter as (A) d (B) d 2 (C) d 4 (D) d

Last Answer : (D) d

The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe) (A) A (B) D (C) 1/A (D) 1/A2

Description : The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe) (A) A (B) D (C) 1/A (D) 1/A2

Last Answer : (C) 1/A

The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

Description : The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

Last Answer : (A) P, Q and R

Assuming flow to be laminar, if the diameter of the pipe is halved, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Be quadrupled

Description : Assuming flow to be laminar, if the diameter of the pipe is halved, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Be quadrupled

Last Answer : (A) Increase

In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder (C) Velocity profile varies hyperbolically and the shear stress remains constant over the cross-section (D) Average flow occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder

Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocity(B) Newton's law of viscosity is not applicable to the turbulent flow of fluidwith linear velocity distribution(C) Laminar flow of viscous liquids is involved in the lubrication of varioustypes of bearings(D) Rise of water in capillary tubes reduces with the increasing diameter ofcapillary tubes

Description : Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocit (B) Newton's law of viscosity is not applicable to the ... types of bearings (D) Rise of water in capillary tubes reduces with the increasing diameter of capillary tubes

Last Answer : (B) Newton's law of viscosity is not applicable to the turbulent flow of fluid with linear velocity distribution

The loss of head due to viscosity for laminar flow in pipes is (where d = Diameter of pipe, l = Length of pipe, v w = Specific weight of the flowing liquid) (A) 4 (B) 8 (C) 16 (D) 32

Description : The loss of head due to viscosity for laminar flow in pipes is (where d = Diameter of pipe, l = Length of pipe, v w = Specific weight of the flowing liquid) (A) 4 (B) 8 (C) 16 (D) 32

Last Answer : Answer: Option D

Pressure drop in a packed bed for laminar flow is given by the __________ equation. (A) Kozeny-Carman (B) Blake-Plummer (C) Leva's (D) Fanning friction factor

Description : Pressure drop in a packed bed for laminar flow is given by the __________ equation. (A) Kozeny-Carman (B) Blake-Plummer (C) Leva's (D) Fanning friction factor

Last Answer : (A) Kozeny-Carman

The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Description : The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Last Answer : (B) Pseudo-plastic

The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Description : The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Last Answer : (A) Newtonian

The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Description : The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Last Answer : (A) Dilatent

Two fluids are flowing through two similar pipes of the same diameter. The Reynold's number is same. For the same flow rate if the viscosity of a fluid is reduced to half the value of the first fluid, the pressure drop will (A) Increase (B) Decrease (C) Remain unchanged (D) Data insufficient to predict relative pressure drop

Description : Two fluids are flowing through two similar pipes of the same diameter. The Reynold's number is same. For the same flow rate if the viscosity of a fluid is reduced to half the value of the ... (A) Increase (B) Decrease (C) Remain unchanged (D) Data insufficient to predict relative pressure drop

Last Answer : (B) Decrease

Which of the following is not a dimension-less group used in catalysis? (Where, D = dispersion co-efficient, cm2 /sec.D1 = diffusion co-efficient; cm2 /sec L = length of the reactor, cm t = time, sec, v = volumetric flow rate, cm3 /sec. V = volume, cm3 .) (A) Reactor dispersion number (D/vL) (B) Reduced time (vt/V) (C) Thiele modulus L √(k/D1 ) (D) None of these

Description : Which of the following is not a dimension-less group used in catalysis? (Where, D = dispersion co-efficient, cm2 /sec.D1 = diffusion co-efficient; cm2 /sec L = length of the reactor, cm t = time, sec, v = volumetric ... (D/vL) (B) Reduced time (vt/V) (C) Thiele modulus L √(k/D1 ) (D) None of these

Last Answer : (D) None of these

For turbulent flow of an incompressible fluid through a pipe, the flow rate ‘Q’ is proportional to (Δ P)n, where ΔP is the pressure drop. The value of exponent 'n' is (A) 1 (B) 0 (C) < 1 (D) > 1

Description : For turbulent flow of an incompressible fluid through a pipe, the flow rate ‘Q’ is proportional to (Δ P)n, where ΔP is the pressure drop. The value of exponent 'n' is (A) 1 (B) 0 (C) < 1 (D) > 1

Last Answer : (C) < 1

he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe at the same flow rate/average velocity, then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Description : he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe ... then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Last Answer : (B) 2Δp

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

The distribution of shear stress in a stream of fluid in a circular tube is(A) Linear with radius for turbulent flow only(B) Linear with radius for laminar flow only(C) Linear with radius for both laminar & turbulent flow(D) Parabolic with radius for both laminar & turbulent flow

Description : The distribution of shear stress in a stream of fluid in a circular tube is (A) Linear with radius for turbulent flow only (B) Linear with radius for laminar flow only (C) Linear with radius for both laminar & turbulent flow (D) Parabolic with radius for both laminar & turbulent flow

Last Answer : (C) Linear with radius for both laminar & turbulent flow

In a fully turbulent flow (Re > 10 5 ) in a pipe of diameter 'd', for a constant pressure gradient, the dependence of volumetric flow rate of an incompressible fluid is (A) d(B) d2(C) d2.5(D) d

Description : In a fully turbulent flow (Re > 10 5 ) in a pipe of diameter 'd', for a constant pressure gradient, the dependence of volumetric flow rate of an incompressible fluid is (A) d (B) d 2 (C) d 2.5 (D) d

Last Answer : (C) d 2.5

Horsepower increase of a centrifugal gas compressor without altering the volumetric flow rate will __________ the gas discharge pressure. (A) Increase (B) Decrease (C) Not change (D) Exponentially decrease

Description : Horsepower increase of a centrifugal gas compressor without altering the volumetric flow rate will __________ the gas discharge pressure. (A) Increase (B) Decrease (C) Not change (D) Exponentially decrease

Last Answer : (A) Increase

For flow of fluids through packed bed, the superficial velocity is (A) Less than the average velocity through channels (B) More than the average velocity through channels (C) Dependent on the pressure drop across the bed (D) Same as the average velocity through channels

Description : For flow of fluids through packed bed, the superficial velocity is (A) Less than the average velocity through channels (B) More than the average velocity through channels (C) Dependent on the pressure drop across the bed (D) Same as the average velocity through channels

Last Answer : (A) Less than the average velocity through channels

Pick out the wrong statement. (A) Momentum transfer in laminar flow results from velocity gradient (B) A fluid in equilibrium is not free from shear stress (C) The viscosity of a non-Newtonian fluid is a function of temperature only (D) Both (B) and (C)

Description : Pick out the wrong statement. (A) Momentum transfer in laminar flow results from velocity gradient (B) A fluid in equilibrium is not free from shear stress (C) The viscosity of a non-Newtonian fluid is a function of temperature only (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Momentum transfer in laminar flow of fluids results due to the (A) Viscosity (B) Density (C) Velocity gradient (D) None of these

Description : Momentum transfer in laminar flow of fluids results due to the (A) Viscosity (B) Density (C) Velocity gradient (D) None of these

Last Answer : (C) Velocity gradient

A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across each field coil C. using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Description : A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across ... using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Last Answer : Answer: B

Asymptotic conditions is reached, when for a fluid flowing in laminar flow through a long tube (A) Exit-fluid temperature > wall temperature (B) Exit fluid temperature < wall temperature (C) Exit fluid temperature = wall temperature (D) Graetz number > 100

Description : Asymptotic conditions is reached, when for a fluid flowing in laminar flow through a long tube (A) Exit-fluid temperature > wall temperature (B) Exit fluid temperature < wall temperature (C) Exit fluid temperature = wall temperature (D) Graetz number > 100

Last Answer : (C) Exit fluid temperature = wall temperature

f = 16/NRe , is valid for (A) Turbulent flow (B) Laminar flow through an open channel(C) Steady flow(D) None of these

Description : f = 16/NRe , is valid for (A) Turbulent flow (B) Laminar flow through an open channel (C) Steady flow (D) None of these

Last Answer : (D) None of these

The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Description : The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Last Answer : (B) x0.8

For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1(B) 0.794 h1(C) 0.574 h1(D) 1.741 h1

Description : For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1 (B) 0.794 h1 (C) 0.574 h1 (D) 1.741 h1

Last Answer : (B) 0.794 h1

Derivation of Thiem's formula Q = 2 (s1 - s2)/2.3 log10 (r2/r1) is based on the assumption (A) The aquifer is homogeneous, isotropic and of infinite depth and area (B) The well is sunk through the full depth of the aquifer (C) The flow lines are radial and horizontal, and the flow is laminar (D) All the above

Description : Derivation of Thiem's formula Q = 2 (s1 - s2)/2.3 log10 (r2/r1) is based on the assumption  (A) The aquifer is homogeneous, isotropic and of infinite depth and area  (B) The well is sunk ... (C) The flow lines are radial and horizontal, and the flow is laminar  (D) All the above 

Last Answer : (D) All the above 

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Description : Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Last Answer : (D) Highly turbulent

The Prandtl mixing length is (A) Zero at the pipe wall and is a universal constant (B) Independent of radial distance from the pipe axis (C) Independent of the shear stress (D) Useful for computing laminar flow problems

Description : The Prandtl mixing length is (A) Zero at the pipe wall and is a universal constant (B) Independent of radial distance from the pipe axis (C) Independent of the shear stress (D) Useful for computing laminar flow problems

Last Answer : (D) Useful for computing laminar flow problems

Prandtl mixing length is (A) Applicable to laminar flow problems (B) A universal constant (C) Zero at the pipe wall (D) None of these

Description : Prandtl mixing length is (A) Applicable to laminar flow problems (B) A universal constant (C) Zero at the pipe wall (D) None of these

Last Answer : (C) Zero at the pipe wall

Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Description : Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Last Answer : (A) Length of the pipe

The most important factor which governs diffusion of drugs across capillaries other than those in the brain is: A. Blood flow through the capillary B. Lipid solubility of the drug C. pKa value of the drug D. pH of the medium

Description : The most important factor which governs diffusion of drugs across capillaries other than those in the brain is: A. Blood flow through the capillary B. Lipid solubility of the drug C. pKa value of the drug D. pH of the medium

Last Answer : A. Blood flow through the capillary

The most important factor which governs diffusion of drugs across capillaries other than those in the brain is: A. Blood flow through the capillary B. Lipid solubility of the drug C. pKa value of the drug D. pH of the medium

Description : The most important factor which governs diffusion of drugs across capillaries other than those in the brain is: A. Blood flow through the capillary B. Lipid solubility of the drug C. pKa value of the drug D. pH of the medium

Last Answer : A. Blood flow through the capillary

Which of the following can be used for the direct measurement of volumetric flow rate of slurry? (A) Venturimeter (B) Orificemeter (C) Rotameter (D) Pitot tube

Description : Which of the following can be used for the direct measurement of volumetric flow rate of slurry? (A) Venturimeter (B) Orificemeter (C) Rotameter (D) Pitot tube

Last Answer : (C) Rotameter

A second order liquid phase reaction, A → B, is carried out in a mixed flow reactor operated in semi batch mode (no exit stream). The reactant A at concentration CAF is fed to the reactor at a volumetric flow rate of F. The volume of the reacting mixture is V and the density of the liquid mixture is constant. The mass balance for A is (A) d(VCA )/dt = -F (CAF - CA ) - kCA 2V (B) d(VCA )/dt = F (CAF - CA ) - kCA 2V (C) d(VCA )/dt = -FCA - kCA 2V (D) d(VCA )/dt = FCAF - kCA 2V

Description : A second order liquid phase reaction, A → B, is carried out in a mixed flow reactor operated in semi batch mode (no exit stream). The reactant A at concentration CAF is fed to the reactor at a volumetric flow rate of F. The volume ... 2V (C) d(VCA )/dt = -FCA - kCA 2V (D) d(VCA )/dt = FCAF - kCA 2V

Last Answer : (D) d(VCA )/dt = FCAF - kCA 2V

The velocity profile for a Bingham plastic fluid flowing (under laminar conditions) in a pipe is (A) Parabolic (B) Flat (C) Flat near the wall and parabolic in the middle (D) Parabolic near the wall and flat in the middle

Description : The velocity profile for a Bingham plastic fluid flowing (under laminar conditions) in a pipe is (A) Parabolic (B) Flat (C) Flat near the wall and parabolic in the middle (D) Parabolic near the wall and flat in the middle

Last Answer : (D) Parabolic near the wall and flat in the middle

In a dry packed bed, the pressure drop will be changed by increasing the flow rate as (A) V1.8 (B) V-0.8 (C) V (D) V-1

Description : In a dry packed bed, the pressure drop will be changed by increasing the flow rate as (A) V1.8 (B) V-0.8 (C) V (D) V-1

Last Answer : (A) V1.8

The length of a wire is increased by 1 mm on the application of a certain load. In a wire of the same material but of twice the length and half the radius, the same force will produce an elongation of (a) 0.5 mm (b) 2 mm (c) 4 mm (d) 8 mm

Description : The length of a wire is increased by 1 mm on the application of a certain load. In a wire of the same material but of twice the length and half the radius, the same force will produce an elongation of (a) 0.5 mm (b) 2 mm (c) 4 mm (d) 8 mm

Last Answer : (d) 8 mm

At the same gas flow rate, the pressure drop in a packed tower being irrigated with liquid __________ that in dry packed tower. (A) Is greater than (B) Is lower than (C) Is same as (D) Cannot be predicted as data are insufficient

Description : At the same gas flow rate, the pressure drop in a packed tower being irrigated with liquid __________ that in dry packed tower. (A) Is greater than (B) Is lower than (C) Is same as (D) Cannot be predicted as data are insufficient

Last Answer : (A) Is greater than

To reduce the tube side pressure drop for the same flow rate, the heat exchanger recommended is (A) 1-2 heat exchanger (B) 1-1 heat exchanger (C) 3-2 heat exchanger (D) 2-4 heat exchanger

Description : To reduce the tube side pressure drop for the same flow rate, the heat exchanger recommended is (A) 1-2 heat exchanger (B) 1-1 heat exchanger (C) 3-2 heat exchanger (D) 2-4 heat exchanger

Last Answer : (B) 1-1 heat exchanger

For the same heat load and mass flow rate in the tube side of a shell and tube heat exchanger, one may use multipass on the tube side, because it (A) Decreases the pressure drop (B) Decreases the outlet temperature of cooling medium (C) Increases the overall heat transfer coefficient (D) None of these

Description : For the same heat load and mass flow rate in the tube side of a shell and tube heat exchanger, one may use multipass on the tube side, because it (A) Decreases the pressure drop (B) ... the outlet temperature of cooling medium (C) Increases the overall heat transfer coefficient (D) None of these

Last Answer : (C) Increases the overall heat transfer coefficient