Enlist general principle of jig and fixture design.

Enlist general principle of jig and fixture design.
by

1 Answer

Answer :

General principle of jig and fixture design.

1. The jig and fixture should be as open as possible to minimize chip or burr accumulation and to enable the operator to remove the chips easily with a brush or an air jet.

2. Fool Proofing

3. Clearance

4. Rigidity

5. Trunions

6. Burr grooves

7. Ejectors

8. Inserts

9. Design for safety

10. Sighting surfaces

11. Simplicity in Design

12. Economical 
by

Related questions

Differentiate in between Jig and fixture.

Description : Differentiate in between Jig and fixture.

Last Answer : Difference between jig and fixture. 

Explain general principles of jigs/fixture design

Description : Explain general principles of jigs/fixture design

Last Answer : 1. Before planning the design of a tool, compare the cost of production of the work with present tools with the expected cost of production, using the tool to be made. Confirm that the cost of ... nearly as possible opposite to some bearing point of the work to avoid springing. 11. Round all corners

State at least eight principles of jigs/ fixture design

Description : State at least eight principles of jigs/ fixture design

Last Answer : The following principles should be considered for design of jigs/ fixtures 1.Rigidity: jigs/ fixtures should be sufficiently stiff/rigid to achieve required accuracy during machining. 2.Fool ... or clearance grooves should be provided for easy removal of metal chips, burrs after machining

Draw proportionate sketch of template jig. State its use.

Description : Draw proportionate sketch of template jig. State its use.

Last Answer : Use of Template jig:- 1) This jig avoids the marking operation completely 2) Drilling is done quickly 3) Easy and Fast loading and unloading of work pieces 4) For drilling flat work pieces they can be accommodated in this jig Sketch :-

Draw the labelled sketch of turning fixture.

Description : Draw the labelled sketch of turning fixture.

Last Answer : Figure: Back plate of Turning Fixture

Enlist general principles of jigs and fixtures

Description : Enlist general principles of jigs and fixtures 

Last Answer : Principles of Jigs and Fixtures:- [1] Location Principle [2] Clamping and guiding Principle [3] Loading and unloading Principle [4] Motion Economy [5] Fool proofing [6] Rigidity [7] Clearance ... safety [14] Ejectors [15] Truninos [16] Inserts [17] Provision of coolant [18] Economy

Enlist the various functions of PPC. Describe: (i) Scheduling (ii) Routing in details.

Description : Enlist the various functions of PPC. Describe: (i) Scheduling (ii) Routing in details.

Last Answer : Functions of PPC: Function related to material selection. Function related to selection of method. Function related to selection of machines and equipment. Routing. * Estimating. Loading ... of operation, machine used, tools and gauges used and standard time for any particular operation.

Enlist any four basic components used in robotics systems also write their functions.

Description : Enlist any four basic components used in robotics systems also write their functions.

Last Answer : Basic components used in robotics system with their functions: 1. Arm: The arm is the part of the robot that positions the end effectors and sensors to do their pre-programmed task. 2. End-effectors ... 6. Drive: The drive is the engine or motor that moves the links into their designated positions.

Enlist any four factors which affect selection of material handling system. Explain which type of material handling system is suitable for: (i) Unloading two wheelers from truck ii) Stacking of pallets in store racks.

Description : Enlist any four factors which affect selection of material handling system. Explain which type of material handling system is suitable for: (i) Unloading two wheelers from truck ii) Stacking of pallets in store racks.

Last Answer : Four Factors affecting Selection of Material Handling System: [1] Adaptability and Flexibility [2] Type of Material to be handled [3] Type of Layout [4] Type of Production [5] ... [11] Cost of installation and handling Suitable Material Handling Devices for Following Activities:

State the types of production system. Enlist four features of mass production system.

Description : State the types of production system. Enlist four features of mass production system.

Last Answer : List of Production System: 1. Intermittent production a. Job order production system. b. Batch order production system. 2. Continuous production a. Mass production system. b. Process production. ... on account of constant repetition of the same job. 9. Per unit cost of product is less

Enlist the various functions of PPC.

Description : Enlist the various functions of PPC.

Last Answer : Functions of Production Planning and Control (PPC):  [1] Material Function: It includes the specification of materials, delivery dates, variety reduction procurement (Standardization) and make or ... all the factors influencing PPC which helps to identify the weak spots and corrective action.

Explain the GANTT chart used in PPC. Enlist advantages and disadvantages of it

Description : Explain the GANTT chart used in PPC. Enlist advantages and disadvantages of it

Last Answer : Gantt chart used in production planning and control. Gantt Chart is a project planning tool that can be used to represent the timing of tasks required to complete a project. Because Gantt chats ... time to maintain. 4. Lack of adequate depiction interrelationship between the separate tasks.

Enlist types of joints used in robotic arm and draw sketch of any two

Description : Enlist types of joints used in robotic arm and draw sketch of any two

Last Answer : Types of Joints [1] Linear Joint or Prismatic joint [2] Orthogonal Joint [3] Rotational joint [4] Twisting Joint [5] Revolving joint

Define dispatching and enlist four functions of dispatching department.

Description : Define dispatching and enlist four functions of dispatching department.

Last Answer : Definition of Dispatching: It is defined as physical handling over of manufacturing order to the operating faculties through release of orders and instructions in accordance with previously developed plan ... and other document from the shops.  6. Issue of inspection order of each operation.

State the types of production system. Enlist four features of batch production system.

Description : State the types of production system. Enlist four features of batch production system.

Last Answer : Types of production system: a. Intermittent production:  1. Job Production 2.Batch production b. Continuous production:  1. Mass production 2. Flow production Features of batch ... adopted in batch production. Example: Pharmaceutical products, ready-made Clothes, Furniture, castings, etc

Explain the principle of working of hydraulic actuator and state its advantages.

Description : Explain the principle of working of hydraulic actuator and state its advantages.

Last Answer : Working Principle of Hydraulic Actuator  1. According to Pascal, when there is an increase in pressure at any point in a confined incompressible fluid, then there is an equal increase at every point in ... better performance than others. 3. Power to weight ratio of these actuators is high.

State and explain the basic principle to be followed to develop a good plant layout.

Description : State and explain the basic principle to be followed to develop a good plant layout.

Last Answer : Following are the basic principle to be followed to develop a good plant layout. 1. Overall integration: A good layout is one that integrates men, materials, machine and supporting ... to the production process. For this purpose there must be sufficient space between different machines.

Explain 3-2-1 principle of locations with suitable example and neat diagram

Description : Explain 3-2-1 principle of locations with suitable example and neat diagram

Last Answer : 3-2-1 Principle of Location used in Jig & Fixtures: It is also known as six pin or six point location principle. In this, the three adjacent locating surfaces of the blank (work piece) are ... [7] Another pin F in the second vertical face of the fixed body, arrests degree of freedom 9.

Explain 3-2-1 principle of location with neat sketch.

Description : Explain 3-2-1 principle of location with neat sketch.

Last Answer : 3-2-1 principle of location  It is also known as six pin or six point location principle. In this, the three adjacent locating surfaces of the blank (work piece) are resting against 3, 2 and 1 pins ... above method of locating a work piece in a fixture is called the 3-2-1 Principle  

What is ejector? Explain role and necessity of ejector in the design of jigs and fixtures.

Description : What is ejector? Explain role and necessity of ejector in the design of jigs and fixtures.

Last Answer : Ejector: Ejector is used to remove the work piece from close fitted locators and is present behind the work piece. Ejector speed up the operation by reducing unloading time. This increases the ... [6] The combined mechanism used in Ejectors can be powered hydraulically or by compressed air. 

List down various types of clamping devices used in design of Jigs. Explain any one with sketch.

Description : List down various types of clamping devices used in design of Jigs. Explain any one with sketch.

Last Answer : List of Types of clamping devices used in design of jigs. i. Screw clamp ii. Pivoted clamp. iii. Equalizing clamp. iv. Latch clamp. v. Wedge clamp. vi. Hinged jaw clamp. ... to be gripped on its edges as shown in figure. This arrangement ensures easy machining of the work piece 

What is ejector? State its necessity in the design of jigs and fixtures.

Description : What is ejector? State its necessity in the design of jigs and fixtures.

Last Answer : Concept of ejector: A device, which is used to remove the work piece from the machine after completion of operation, is known as ejector. Necessity: In the design of jigs and fixture , ... been machined. Ejector speeds up the unloading of the work piece and thus increases the production rate.

Explain the design principles of plant layout.

Description : Explain the design principles of plant layout.

Last Answer : Design Principles of Plant Layout: S.N. Design Principles Description 1 Principle of Integration All the plant facilities should be fully integrated into a single operating unit ... should be utilized in an optimum manner so as to result in minimum initial capital investment.

From which of the following is robot programming language. (A) VAL (B) AML(C) ABD (D) Both (A) & (B)

Description : From which of the following is robot programming language. (A) VAL (B) AML (C) ABD (D) Both (A) & (B)

Last Answer : D

____ grippers are used to transfer ferrous material. (A) Magnetic grippers (B) Mechanical grippers (C) Adhesive grippers (D) Vacuum cup grippers

Description : ____ grippers are used to transfer ferrous material. (A) Magnetic grippers (B) Mechanical grippers (C) Adhesive grippers (D) Vacuum cup grippers

Last Answer : A

____ grippers are used to pick up light weight materials such as paper,cloth etc. (A) Mechanical grippers (B) Adhesive grippers (C) Vacuum cup grippers (D) Magnetic grippers

Description : ____ grippers are used to pick up light weight materials such as paper,cloth etc. (A) Mechanical grippers (B) Adhesive grippers (C) Vacuum cup grippers (D) Magnetic grippers

Last Answer : B

From which of the following is the type of robot. (A) Point to point robots (B) Continue path robot (C) Jointed arm robots (D) All of the above

Description : From which of the following is the type of robot. (A) Point to point robots (B) Continue path robot (C) Jointed arm robots (D) All of the above

Last Answer : D

Grippers are used to_____. (A) Hold the objects (B) Sense the objects (C) Move the objects (D) Both (A) & (C)

Description : Grippers are used to_____. (A) Hold the objects (B) Sense the objects (C) Move the objects (D) Both (A) & (C)

Last Answer : D

The capacity of robot to carry load is known as_____. (A) Load carrying capacity (B) Work envelope (C) Maximum reach (D) None of the above

Description : The capacity of robot to carry load is known as_____. (A) Load carrying capacity (B) Work envelope (C) Maximum reach (D) None of the above

Last Answer : A

The capacity of robot to carry load is known as_____. (A) Load carrying capacity (B) Work envelope (C) Maximum reach (D) None of the above

Description : The capacity of robot to carry load is known as_____. (A) Load carrying capacity (B) Work envelope (C) Maximum reach (D) None of the above

Last Answer : C

The speed at which robot is capable of manipulating its end effector is known as the____. (A) Velocity of robot (B) Maximum reach (C) Speed of movement (D) Load carrying capacity

Description : The speed at which robot is capable of manipulating its end effector is known as the____. (A) Velocity of robot (B) Maximum reach (C) Speed of movement (D) Load carrying capacity

Last Answer : C

Which is also known as work volume of robot. (A) Work envelope (B) Speed of movement(C) Load carrying capacity (D) Precision of movement

Description : Which is also known as work volume of robot. (A) Work envelope (B) Speed of movement(C) Load carrying capacity (D) Precision of movement

Last Answer : A

From which of the following is benefit of robot. (A) Variety of task (B) Computer control (C) Repetitive task (D) All of the above

Description : From which of the following is benefit of robot. (A) Variety of task (B) Computer control (C) Repetitive task (D) All of the above

Last Answer : D

Which is area of engineering and science which understand the different principles, structure and programming of robot. (A) Mechatronics (B) Robotics (C) Aeronautics (D) None of the above

Description : Which is area of engineering and science which understand the different principles, structure and programming of robot. (A) Mechatronics (B) Robotics (C) Aeronautics (D) None of the above

Last Answer : B

What is end effector? Give its classification

Description : What is end effector? Give its classification 

Last Answer : In robotics, an end effector is a device or tool that's connected to the end of a robot arm where the hand would be. The end effector is the part of the robot that interacts with the ... designed. Classification:- i) Mechanical clamping ii) Magnetic clamping iii) Vocum (suction) gripping

How ‘5s’ can be used as inventory reduction technique?

Description : How ‘5s’ can be used as inventory reduction technique? 

Last Answer : By applying 5S in industry to systematically results- Total organization, cleanliness and standardization in work piece. Well organized workplace. More efficient workplace. More ... of waste & making cleanliness  4. SEIKETSU means standardizing 5. SHITSUKE means self discipline 

What allowances are considered while calculating standard time?

Description : What allowances are considered while calculating standard time? 

Last Answer : following types of allowances are considered while calculating standard time. 1) Relaxation allowance a) Personal need allowance b) Fatigue allowance i) Basic fatigue allowance ii) Variable ... 2) Contingency allowance 3) Special allowance 4) Process allowance 5) Interference allowance

What is group technology? Give its applications.

Description : What is group technology? Give its applications.

Last Answer : Group technology is based on the general principle that many problems are similar and by grouping similar problems single solution can be found to a set of problems thus saving time and efforts. ... is used for manufacturing in automobile industry, fast food chains, doctors and dentists etc.  

State the advantages and disadvantages of combined operations.

Description : State the advantages and disadvantages of combined operations. 

Last Answer : combined operation:- if the number of operations are combined in one setting it is possible to reduce the production time and the operations can be performed with more accuracy. Advantages of ... More costly set up 3) Trained operators are necessary 4) Sometimes special machines are needed 

Explain the concept of AGV? State it’s any two applications.

Description :  Explain the concept of AGV? State it’s any two applications. 

Last Answer : AGV is the battery operated programmed vehicle, used to carry load from one location to another by following a prescribed path around the manufacturing floor. It is a driverless vehicle, ... System) 2) AGV material handling system is very suited to computer integrated manufacturing system  

Explain various Robot configurations with neat sketch.

Description : Explain various Robot configurations with neat sketch. 

Last Answer : Different Robot Configurations: Robots are being classified on the basis of their physical configuration and control systems adopted. These classifications are briefly described as below: [1] ... direction for vertical insertion tasks. It is basically used for the assembly purpose.

Explain in brief the allowances to be considered while estimating the standard time.

Description : Explain in brief the allowances to be considered while estimating the standard time.

Last Answer : Allowances to be considered while estimating the Standard Time: Allowances are added to the normal time in order to arrive at standard time. It is impossible to work throughout the day even ... under exceptional circumstances. It is used with utmost care and only in clearly defined circumstances.

State advantages and disadvantages of ERP System.

Description : State advantages and disadvantages of ERP System. 

Last Answer : Advantages of ERP System: [1] Improved efficiency across business due to timely availability of information. [2] Better decision making owing to information integration. [3] Reduced inventory costs due ... [9] Lack of support from the ERP vendor, consultancy firm or the hardware vendor.

State the functions of production planning.

Description : State the functions of production planning.

Last Answer : Function of Production Planning: Production planning is the determination, acquisition and arrangement of all facilities necessary for future production of products. It performs following functions; [1] To ... ; D. [4] To efficiently utilize the available resources and plant facilities.

Give classification of robot sensor.

Description : Give classification of robot sensor. 

Last Answer : Classification of Robot Sensor: Robot Sensors senses and capability includes vision and hand eye coordination, touch, hearing, sensors will divided into the following categories.  [1] Vision Sensor: ... and the stored vocabulary word the robot performs some actions which correspond to the word. 

Explain the concept of JIT and how does it help the manufacturing system to improve productivity?

Description : Explain the concept of JIT and how does it help the manufacturing system to improve productivity?

Last Answer : Concept of JIT: [1] JIT is a Production methodology which aims to improve overall productivity through elimination of waste and which leads to improved quality. [2] JIT concept was ... ] It improves customer satisfaction [14] It improves working condition and relation between employees. 

Explain the importance of ‘5S’ (“Five S”) Concept.

Description : Explain the importance of ‘5S’ (“Five S”) Concept.

Last Answer : Introduction of 5 S Concept: [1] 5S is a process of workplace organization and housekeeping which is carried out gradually and systematically. [2] It is a structured program to implement workplace ... In fact, 5S is a basic step in a journey towards Total Quality Management (TQM).

What are the different types of Fixtures? Explain any one with sketch.

Description : What are the different types of Fixtures? Explain any one with sketch.

Last Answer : Types of Fixtures: Following are the types of Fixtures according to the type of machine operations for which they are used. [1] Lathe (Turning) Fixture [2] Milling fixtures  [3] Grinding ... relative to the tool of the machine table and guide the broaching tool in relation to the job. 

Explain the following terms in context with work study.

Description : Explain the following terms in context with work study.

Last Answer : i. Therbligs. ii. MTM (Method Time Measurement)  Therbligs :  1. Therbligs are used to describe the basic element of movement or fundamental hand motions of the work cycle. 2. Every ... sum of these motion times is the time an operator of average skill would take to perform the task.

State the various stages at which inspection should be planned.

Description : State the various stages at which inspection should be planned. 

Last Answer : Stages of inspection: 1. Inspection of incoming materials, raw materials or received materials including bought out items. 2. In process inspection: It includes following stages; a. ... on completed assemblies under conditions similar to field conditions.  3. Inspection of finished goods.