State any Four specifictions of capacitor and explain any two in details.

State any Four specifictions of capacitor and explain any two in details.
by

1 Answer

Answer :

Specifictions of capacitor:

1.Dielectric material

2.Capacitance value

3.Working voltage

4.Tolerence

5.Temperature coefficient

6.Power factor

7.C/V ratio

9.Insulation resistance

Explanation:

1.Working voltage : It is the maximum voltage at which capacitor can operate without failure

2.Power factor : It is the ratio of resistance to reactance at the operating frequency.

3 Tolerance: It is the maximum possible deviation on either side from actual value.

4.C/V ratio: It is the ratio of capacitance to volume.
by

Related questions

Write four specifications of capacitor. Write the range of values for any one type of capacitor.

Description : Write four specifications of capacitor. Write the range of values for any one type of capacitor.

Last Answer : Specifications of capacitor are: i. Working voltage ii. Capacitive reactance iii. Dissipation factor iv. Frequency characteristics v. Equivalent series resistance vi. Quality Factor vii. Tolerance Electrolytic capacitor= 0.47μF to 10,000μF

Explain the colour coding using colour band system in capacitor with an example.

Description : Explain the colour coding using colour band system in capacitor with an example.

Last Answer : 1. First and second band gives the significant digit reading from left to right. 2. Third colour band gives the multiplier. 3. Fourth colour band gives the tolerance value. 4. Fifth and sixth bands ... , Violet, Yellow To find : Value of capacitor Solution: Yellow: 4  Violet: 7

Explain the working principle of electrolytic capacitor.

Description : Explain the working principle of electrolytic capacitor.

Last Answer : Principle: Electrolytic capacitors are using a chemical feature of some special metals, on which by anodically oxidation, an insulating oxide layer or dielectric originates. The metal is placed in an ... form the thin oxide dielectric, this type of capacitor is called electrolytic'.

With help of constructional diagram, explain working of air-gang capacitor.

Description : With help of constructional diagram, explain working of air-gang capacitor.

Last Answer : Construction of air-gang capacitor : Air gang capacitors are capacitors which use air as their dielectric. The simplest air capacitors are made of two conductive plates separated by an air gap.   ... capacitor. The rotor plates are attached to the shaft that is used to adjust the capacitance. 

With help of circuit diagram and waveform, explain shunt capacitor filter.

Description : With help of circuit diagram and waveform, explain shunt capacitor filter.

Last Answer : Circuit diagram and Waveform: OR Explanation: A filter circuit is one which removes the ac component present in the rectified output and allows the dc component to reach the ... which allows ac components. The remaining dc components present in the signal are collected at the output. 

State the advantages and disadvantages of series inductor and shunt capacitor filter.

Description : State the advantages and disadvantages of series inductor and shunt capacitor filter.

Last Answer : Advantages of series inductor filter 1. It has low ripple factor at heavy load currents (i.e. low load resistance) 2. It has no surge current through the diode. 3. It reduces the ripple in the DC ... . 3. It has low output voltages for heavy loads. 4. Ripple factor is dependent on the load.

State the functions of following essential parts of electrolytic capacitor. 1. Aluminium foil 2. Oxide film 3. Spacers 4. Aluminium container

Description : State the functions of following essential parts of electrolytic capacitor. 1. Aluminium foil 2. Oxide film 3. Spacers 4. Aluminium container

Last Answer : 1. Aluminium Foil – It serves as a positive electrode called anode  2. Oxide film – It acts as a dielectric medium.  3. Spacer- It is used to provide separation and hold the electrolyte.  4. Aluminium container- It serves as a negative electrode called cathode.

State the specifications of capacitor.

Description : State the specifications of capacitor.

Last Answer : The important specifications of capacitor are: 1. Capacitance ( C ) Value 2. Dielectric material 3. Working Voltage (WV) 4. Power factor 5. Physical Size 6. Insulation resistance 7. C/ ... ( %) 9 Leakage Current 10 Temperature Coefficient (TC) 11 Equivalent Series Resistance ( ESR )

Draw construction of PVC gang capacitor and describe it’s working.

Description : Draw construction of PVC gang capacitor and describe it’s working.

Last Answer :  Diagram Working  In plastic core capacitor, poly-vinyl chloride (PVC) type of plastic film is used as dielectric between the fixed & movable vanes instead of air. This increases ... & results in great reduction of size of capacitor in comparison with the air core capacitor.

Describe construction of Aluminium Electrolytic capacitor.

Description : Describe construction of Aluminium Electrolytic capacitor.

Last Answer : A plain foil dry electrolytic capacitor is made by forming a coating of aluminium oxide on both sides of an aluminium foil. Two strips of aluminium foil used are then separated by two layers of porous ... is rolled up the ends closed with wax and then sealed into an aluminium container.

Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Description : Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Last Answer : Fig: Shunt capacitor filter along with full wave rectifier Fig: Waveform of full wave rectifier output and shunt capacitor filter output.

What is dielectric material? Enlist dielectric material used in capacitor.

Description : What is dielectric material? Enlist dielectric material used in capacitor.

Last Answer : A dielectric material is an electrical insulator that can be polarized by an applied electric field. Dielectric materials used in capacitor: porcelain (ceramic), mica, glass, plastics, and the oxides of various metals

Describe working of variable air gang capacitor with neat sketch.

Description : Describe working of variable air gang capacitor with neat sketch.

Last Answer : ( OR)   working: Consider the structure of the above figure. It mainly consists of two sets of aluminium plates separated from each other by air. These metal plates may be rotary or ... when the shaft is rotated. Sometimes, two or more such capacitors are operated by a single shaft.  

Draw and describe constructional diagram of electrolytic capacitor.

Description : Draw and describe constructional diagram of electrolytic capacitor.

Last Answer : Electrolytic capacitor is a polarized capacitor. This type of capacitor consists of pasty, semiliquid electrolyte between aluminum foil electrodes or plates. An electrolytic capacitor is a type ... the ends closed with wax and then sealed into an aluminium container as shown in fig. 

Draw the symbol of i) Iron core inductor ii) variable capacitor iii) resistor iv) Ferrite core inductor

Description : Draw the symbol of i) Iron core inductor ii) variable capacitor iii) resistor iv) Ferrite core inductor

Last Answer :  Iron core inductor:  Ferrite core inductor:  

Give the detail classification of capacitor.

Description : Give the detail classification of capacitor. 

Last Answer : classification of capacitor :

State four applications of PIN diode.

Description : State four applications of PIN diode. 

Last Answer : i. Used in rectifier circuit. ii. Used in clipping and clamping circuit. iii. Used for A.M detection. iv. Used for voltage multiplier.

Draw construction of Schottky diode and state it’s four applications.

Description : Draw construction of Schottky diode and state it’s four applications.

Last Answer : Applications :- 1. RF mixer and detector diode: 2. Power rectifier 3. Voltage clamping 4. Stand alone photovoltaic systems in order to prevent batteries from discharging purpose for the solar panels at night 5. Rectifiers in power supplies.

State any Four applications of PN junction diode.

Description : State any Four applications of PN junction diode.

Last Answer : 1. Rectifiers in power supplies, 2. Detectors in RF, 3 .Clippers, 4. In clamping networks used as DC Restorers, 5. As switches in digital logic circuits.

List four specifications of zener diode or P- N junction diode.

Description : List four specifications of zener diode or P- N junction diode.

Last Answer : Specifications of zener diode: 1. Zener voltage 2. Power dissipation 3. Maximum power dissipation PD(max) 4. Breakdown current 5. Dynamic resistance 6. Maximum reverse current. (OR) ... Reverse saturation current 5. Power dissipation 6. Junction temperature 7. Peak inverse voltage (PIV)

Give the classification of resistors. List any four materials used for manufacturing of resistors.

Description : Give the classification of resistors. List any four materials used for manufacturing of resistors.

Last Answer : Materials used for manufacturing of resistors: Carbon Composition Resistor (carbon dust or graphite paste) Film or Cermet Resistor (conductive metal oxide paste) Nichrome, enamel LDR- Cadmium sulphide, Cadmium selenide, lead sulphide TDR- Cobalt, Nickel, Manganese

List four dielectric materials used for capacitors.

Description : List four dielectric materials used for capacitors. 

Last Answer : 1. Mica, glass, ceramic 2. High permittivity ceramic 3. Paper and metallized paper 4. Electrolytic : Oxide film, tantalum 5. Dielectrics such as polystyrene, polythene polytetrafluoroethylene.

List any four applications of laser diode.

Description : List any four applications of laser diode.

Last Answer : 1. As light source in fiber optic communication. 2. In the infrared spectrometers. 3. In the medical field. 4. In military applications. 5. To measure distance, alignment angle etc. 6. For flow ... . 9. For welding. 10. For sound recording and reproduction (in CD players) 11. In holography.

List four specifications of resistor.

Description : List four specifications of resistor.

Last Answer : specifications of resistor: 1. Resistance value 2. Tolerance 3. Power rating 4. Maximum operating temperature 5. Maximum operating voltage 6. Frequency range 7. Temperature coefficient of resistance 8. Wattage

State and explain superposition theorem.

Description : State and explain superposition theorem.

Last Answer : Superposition theorem states that: In a linear circuit with several sources the voltage and current responses in any branch is the algebraic sum of the voltage and current responses due to each source acting ... branch to find the response on the branch due to the combined effect of all the sources.

State and explain Thevenin’s theorem

Description : State and explain Thevenin’s theorem

Last Answer : Thevenin's Theorem states that Any linear circuit containing several voltages and resistances can be replaced by just one single voltage in series with a single resistance connected across the load . ... Thevenin's equivalent resistance Rth forms Thevenin's equivalent circuit as shown below.

State and explain Thevenin’s theorem with suitable example.

Description : State and explain Thevenin’s theorem with suitable example.

Last Answer : Statement: Any network containing active and/or passive elements and one or more dependent and/or independent voltage/or current sources can be replaced by an equivalent network containing a voltage source ( ... given by IL =VTH/ (RTH+RL) figures above illustrate the concept of Thevenin s theorem

List specifications of resistors and explain any two.

Description : List specifications of resistors and explain any two.

Last Answer : List specifications of resistors are as follows: 1. Maximum voltage rating. 2. Power rating. 3. Temperature co- efficient of resistance. 4. Tolerance. 5. Operating temperature. 6. Ohmic ... form of energy. Tolerance: It is defined as deviation from nominal value of resistance in percent.

Explain the working principle of slug tuned inductor.

Description : Explain the working principle of slug tuned inductor.

Last Answer : The value of inductor increases, when the slug (moving coil) is moved into the coil winding and hence decreases the resonant frequency of the tuned circuit. Similarly, when the slug is moved out of the ... be varied by using movable core which can be moved up or down by using screw driver.

Explain the following terms 1. Bilateral Network 2. Linear Network

Description : Explain the following terms 1. Bilateral Network 2. Linear Network

Last Answer : Bilateral Network If the magnitude of current flowing through a circuit element is not affected when the polarity of the applied voltage is changed, then the element is known as a bilateral element. ... network comprising of one or more linear number of elements is known as a linear network.

Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode.

Description : Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode. 

Last Answer : Construction A PIN diode is made up of three semiconductor materials; two heavily doped P- and N- type material separated by an intrinsic (undoped) semiconductor (I) as shown in above figure ... . This advantage allows the PIN diode to process even weak signals.  Characteristics

Explain the working of TDR along with its symbol and characteristics.

Description : Explain the working of TDR along with its symbol and characteristics. 

Last Answer : TDR are also called as thermistors. Thermally sensitive materials are used to manufacture thermistors. Depending on the temperature co- efficient of resistance value thermistors are classified as ... used when a drastic change in resistance is required at specific temperature. RαT

With help of circuit diagram and waveform, explain working of positive series clipper.

Description : With help of circuit diagram and waveform, explain working of positive series clipper.

Last Answer : Series Clipper (Positive):-   Working: For positive cycle the diode D is reverse biased. Hence there is no voltage across the load RL While for negative half wave, the diode D is forward biased. Hence ... positive cycle of the input voltage gets clipped off. Input & o/p wave form:-   

With help of circuit diagram and waveform, explain working of CLC or π- filter.

Description : With help of circuit diagram and waveform, explain working of CLC or π- filter.

Last Answer : Circuit diagram CLC or Π filter:   Working : It consist of a filter capacitor C1 connected across the rectifier o/p , a choke L is series and another filter capacitor C2 connected across the load. ... to block. Therefore, only d.c component appears across the load and that is what we desire.  

Draw and explain V-I characteristics of a P-N junction diode.

Description : Draw and explain V-I characteristics of a P-N junction diode.

Last Answer : V-I Characteristics of a P-N junction: V-I characteristics of a Diode: The V-I characteristics can be divided in two parts. 1. Forward characteristics. 2. Reverse ... plot a graph with reverse voltage on horizontal axis and current on vertical axis, we obtain reverse characteristics.

With help of constructiobal diagram, explain working of slug tunned inductor.

Description : With help of constructiobal diagram, explain working of slug tunned inductor.

Last Answer : The variable inductor having an adjustable ferrite core is known as slug tuned inductor. The value of inductance increases or decreases respectively, due to the movement of a ferrite core into or out of ... be varied by using movable core which can be moved up or down by using screw driver. 

With help of constructional diagram, explain working of LDR.

Description : With help of constructional diagram, explain working of LDR.

Last Answer : Working of LDR: Due to the radiant energy supplied to the semiconductor, the covalent bonds are broken and the electron hole pairs are generated resulting into flow of current. These increased ... resistance of the LDR will decrease with increase in the intensity of incident light.

Explain the following terms: (1) Unilateral network (2) Bilateral network

Description : Explain the following terms: (1) Unilateral network (2) Bilateral network

Last Answer : Unilateral network: It is a network whose properties or characteristics change with the direction of its operation. Eg: Network consisting of Diode. Current flows in only one direction.  Bilateral ... directions. In this network impedance is same in both directions. Eg: All resistive networks.

Draw and explain the working of combinational Clipper with waveforms.

Description : Draw and explain the working of combinational Clipper with waveforms.

Last Answer : Explanation:- As shown in figure the combinational clipper is the combination of positive biased and negative biased clipper. The combinational clipper can be used to clip both two independent ... open circuit. Hence the value of output voltage cannot exceed the voltage level of VB2. 

Explain with neat circuit, concept of open circuit and short circuit.

Description : Explain with neat circuit, concept of open circuit and short circuit.

Last Answer : Open Circuit  Two points in a circuit are said to be open circuited if there is no circuit element or direct connection between them. An open circuit exist between points A and B in ... short circuited in below figure. The resistance between short circuited points is zero. RAB= 0Ω

With the help of constructional diagram, explain the working of LDR with neat sketch.

Description : With the help of constructional diagram, explain the working of LDR with neat sketch.

Last Answer : Working Principle The resistance depends on the intensity of light, as resistance decreases with increase in light intensity. Characteristics Applications of LDR 1. They are often ... circuits, light intensity meters, for counting the packages moving on a conveyor belt, etc.

With the help of circuit diagram and waveforms, explain working of RC differentiator.

Description : With the help of circuit diagram and waveforms, explain working of RC differentiator.

Last Answer : Fig: RC differentiating circuit Figure shows a RC differential circuit. It is also known as high pass filter. The reactance of a capacitor decreases with increasing frequency. The higher ... i.e. the output signal is directly proportional to the derivative of the input signal.  

Draw and explain B-H curve.

Description : Draw and explain B-H curve.

Last Answer : Diagram: Explanation: B-H curve is obtained while plotting the graph between B & H for a magnetic material while magnetized through one complete cycle of magnetization. The value of ... measure of the energy dissipated due to hysteresis, more the area higher is the hysteresis loss. 

Draw negative clamper circuit and explain its working.

Description : Draw negative clamper circuit and explain its working. 

Last Answer : Diagram: Working: During the positive half cycle of the input AC signal, the diode is forward biased and hence no signal appears at the output. In forward biased condition, the diode allows ... - 2Vm} which have the same polarity with each other. As a result, the signal shifted downwards. 

State two functions of slug- tuned inductor and write the expression of self-inductance.

Description : State two functions of slug- tuned inductor and write the expression of self-inductance.

Last Answer : It is kind of variable inductor. The value of inductance increases, when the slug is moved into the coil winding and decreases the resonant frequency. When the slug is moved out of the coil ... decreases and resonant frequency of the tuned circuit increases. Self-inductance (L)= N x φ /I

Draw the characteristics of tunnel diode, showing operating regions. State two applications of tunnel diode.

Description : Draw the characteristics of tunnel diode, showing operating regions. State two applications of tunnel diode.

Last Answer : Applications: One of the important application of a tunnel diode is in high speed computers where the switching times in the order of nanoseconds or picoseconds are desirable. A tunnel diode can be ... In digital networks. 2. As a high speed switch. 3. As a high frequency oscillator.

Write working principle of photodiode and state its two applications.

Description : Write working principle of photodiode and state its two applications.

Last Answer : Working principle of photodiode:   Working principle: A photodiode is a PN- junction diode that consumes light energy to produce electric current. Sometimes it is also called as photo- ... Optical remote control Smoke detectors Flame detectors Intruder alert security system 

What is magnetic material ? State it’s two applications.

Description : What is magnetic material ? State it’s two applications.

Last Answer : Magnetic materials are those materials that can be either attracted or repelled when placed in an external magnetic field and can be magnetized themselves. OR The materials which provide path to ... . Applications: 1.Floppy disc ,hard disc  2.Motors and generators  3.Biomedical equipment

Draw the star and delta connection. State any one conversion formula.

Description : Draw the star and delta connection. State any one conversion formula.

Last Answer : star and delta connection

State the condition for RC differentiator. Draw the output waveform of RC integrator for square wave input.

Description : State the condition for RC differentiator. Draw the output waveform of RC integrator for square wave input.

Last Answer : Condition for RC differentiator: If the time duration T of the input waveform is comparable with the RC time constant (product of R and C) then the output waveform of the differentiator gets distorted. Hence for proper differentiator the condition is as follows: T >>RC