Description : 1357 + 294 + 487 -3412 +8765 -5793= ? a) 1444 b) 2588 c) 1698 d) 2155 e) 1241
Last Answer : ? =(1357 + 294 +487+8765)-(3412+5793) =10903-9205=1698 Answer: c)
Description : The maximum velocity of a body in SHM with amplitude of 150 mm and a frequency 2 vibrations/sec is equal to a.1.885 m/sec b.0.01885 m/sec c.0.1885 m/sec d.18.55 m/sec e.185.5 m/sec
Last Answer : a. 1.885 m/sec
Description : A wire of mild steel has initial length 1.5 m and diameter 0.60 mm is extended by 6.3 mm
Last Answer : A wire of mild steel has initial length 1.5 m and diameter 0.60 mm is extended by 6.3 mm when a ... is 2.1 1011 N/m2, calculate the force applied.
Description : A thick wire of radius `r=5 mm` carries a steady current `I=10 A`. An electron leaves its surface perpendicularly with velocity `v_(0)=10^(6) m//s`. F
Last Answer : A thick wire of radius `r=5 mm` carries a steady current `I=10 A`. An electron leaves its ... from the surface of the wire before it turns back.
Description : The temperature coefficient of copper is `0.004^(@)C^(-1)`. Find the resistance of a 5 m long copper wire of diameter 0.2 mm at `100^(@)C`, if the res
Last Answer : The temperature coefficient of copper is `0.004^(@)C^(-1)`. Find the resistance of a 5 m long copper wire of ... `0^(@)C` is `1.7xx10^(-8) Omega` m.
Description : A current of 2 A is flowing through a wire of length 4 m and cross-sectional area `1 mm^(2)`. If each cubic metre of the wire contains `10^(29)` free
Last Answer : A current of 2 A is flowing through a wire of length 4 m and cross-sectional area `1 mm^(2)` ... taken by an electron to cross the length of the wire.
Description : What length of a wire of diameter 0.46 mm and specific resistance `50xx10^(-6) Omega`m would be required to make a coil of resistance `10 Omega` ?
Last Answer : What length of a wire of diameter 0.46 mm and specific resistance `50xx10^(-6) Omega`m would be required to make a coil of resistance `10 Omega` ?
Description : A rheostat has 100 turns of a wire of radius 0.4 mm having resistivity `4.2xx10^(-7) Omega`m. The diameter of each turn is 3 cm. What is the maximum v
Last Answer : A rheostat has 100 turns of a wire of radius 0.4 mm having resistivity `4.2xx10^(-7) ... the maximum value of resistance that it can introduce ?
Description : Calculate the resistance of a 2 m long nichrome wire of radius 0.321 mm. Resistivity of nichrome is `15xx10^(-6) Omega` m. If a potential difference o
Last Answer : Calculate the resistance of a 2 m long nichrome wire of radius 0.321 mm. Resistivity of nichrome is ` ... wire, what will be the current in the wire ?
Description : The resistance of a conductivity wire of length 1.1 m and of diameter 0.14 mm is `30 Omega`. Calculate its resistivity.
Last Answer : The resistance of a conductivity wire of length 1.1 m and of diameter 0.14 mm is `30 Omega`. Calculate its resistivity.
Description : What is 720 mm in m?
Last Answer : Since a millimeter is 0.001 meters, 720 mm equal 0.72meters.
Description : Is 60 mm greater than 6 m?
Last Answer : is 6cm greater than 60mm
Description : Which of the following statements about septic shock are true? A. A circulating myocardial depressant factor may account for the cardiac dysfunction sometimes seen with shock due to sepsis or ... animal studies that demonstrate a significant improvement in survival with the use of such agents.
Last Answer : Answer: AB DISCUSSION: Shock due to sepsis or SIRS frequently manifests as a hyperdynamic cardiovascular response, consisting of an elevated CI and a decreased SVR or SVRI. Occasionally, ... been encouraging thus far in human clinical trials, despite the promising results from many animal studies
Description : A sewer pipe contains 1 mm sand particles of specific gravity 2.65 and 5 mm organic particles of specific gravity 1.2, the minimum velocity required for removing the sewerage, is A. 0.30 m/sec B. 0.35 m/sec C. 0.40 m/sec D. 0.45 m/sec
Last Answer : ANS: D
Description : The settling velocity of the particles larger than 0.06 mm in a settling tank of depth 2.4 is 0.33 m per sec. The detention period recommended for the tank, is A. 30 minutes B. 1 hour C. 1 hour and 30 minutes D. 2 hours
Description : At what particular wavelength is solar flux measured? A. 10.7 mm band B. 10.7 m band C. 10.7 cm band D. 10.7 nm band
Last Answer : C. 10.7 cm band
Description : What is the typical separation between the two conductors in a parallel wire line? A. 0.001 to 0.01 m B. 200 to 500 mm C. 0.635 to 15.24 cm D. 2.5 to 5 in.
Last Answer : C. 0.635 to 15.24 cm
Description : What is the critical rotation speed in revolutions per second, for a ball mill of 1.2 m diameter charged with 70 mm dia balls? (A) 0.5 (B) 1.0 (C) 2.76 (D) 0.66
Last Answer : (D) 0.66
Description : The designation M 36 × 2 means (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch (B) Metric coarse threads of 36 mm outside diameter and 2 mm pitch (C) Metric threads of 36 mm pitch diameter and 2 mm pitch (D) Metric threads of 36 mm core diameter and 2 mm pitch
Last Answer : (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch
Description : The static deflection of a spring under gravity, when a mass of 1 kg is suspended from it, is 1 mm. Assume the acceleration due to gravity g = 10 m/s^2. The natural frequency of this spring-mass system (in rad/s) is A 100 B 150 C 200 D 250
Last Answer : A 100
Description : A cantilever shaft having 50 mm diameter and a length of 300mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the static deflection of shaft in mm. A 0.144 B 0.244 C 0.344 D 0.444
Last Answer : A 0.144
Description : From above numerical find the static deflection A 0.0245 mm B 0.0025 mm C 0.0245 m D 0.0245 cm
Last Answer : C 0.0245 m
Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free enD. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. A. 575B. 625 C. 525 D. 550
Last Answer : A. 575
Description : A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 3 . Determine the static deflection of the shaft in mm. a) 0.147 b) 0.213 c) 0.132 d) 0.112
Last Answer : a) 0.147
Description : A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Determine the frequency of transverse vibrations of the shaft. a) 31 b) 35 c) 37 d) 41
Last Answer : d) 41
Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. a) 575 b) 625 c) 525 d) 550
Last Answer : a) 575
Description : Flat rate parcel rates Flat Rate Parcel Boxes size Dimension of boxes (in mm) Weight (in Kg.) Tariff (in Rs.) Small - S 250*50*300 0 to 1 125 Medium - M 250*100*300 Above 1 to 2.5 200 Large - L 300*250*200 Above 2.5 to 5 400
Last Answer : Large - L 300*250*200 Above 2.5 to 5 400
Description : . A 0.5 m high bed made up of a 1 mm dia glass sphere (density 2500 kg/m3 ) is to be fluidised by water (density 1000 kg/m3 ). If at the point of incipient fluidisation, the bed voidage is 40%, the pressure drop across the bed is (A) 4.4 KPa (B) 2.94 KPa (C) 3.7 KPa (D) None of these
Last Answer : (A) 4.4 KPa
Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle ... fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s
Last Answer : (B) 16 mm/s
Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the ... , is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Last Answer : (C) 20 mm
Description : A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson's ratio is 0.25, the change in the volume of the bar is: (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm
Last Answer : (C) 3.125 cm
Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option
Last Answer : (C) 120 N/mm
Description : A rolled steel joist is simply supported at its ends and carries a uniformly distributed load which causes a maximum deflection of 10 mm and slope at the ends of 0.002 radian. The length of the joist will be, (A) 10 m (B) 12 m (C) 14 m (D) 16 m
Last Answer : (D) 16 m
Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 ... joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm
Last Answer : (D) 400 mm
Description : The minimum range for sliding the focusing lens in the internal focusing telescope for focusing at all distances beyond 4 m is (A) 5 mm (B) 10 mm (C) 15 mm (D) 20 mm
Last Answer : (D) 20 mm
Description : The 10 mm markings on a levelling staff placed at 20 m are separated by (A) 1/1000 radian (B) 1/1500 radian (C) 1/2000 radian (D) 1/2500 radian
Last Answer : (C) 1/2000 radian
Description : A standard steel tape of length 30 m and cross-section 15 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of ... (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these
Last Answer : (A) - 0.000909 m
Description : Which of the following introduces an error of about 1 in 1000 if 20 m chain is used? (A) Length of chain 20 mm wrong (B) One end of the chain 0.9 m off the line (C) One end of chain 0.9 m higher than the other (D) All the above
Last Answer : (D) All the above
Description : The desired sensitivity of a bubble tube with 2 mm divisions is 30". The radius of the bubble tube should be (A) 13.75 m (B) 3.44 m (C) 1375 m (D) None of these
Last Answer : (A) 13.75 m
Description : Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in ... ) A 100 m tape of cross section 10 mm 0.25 mm stretches about 10 mm under 5 kg pull
Last Answer : (B) An increase in temperature causes a tape to increase in length and the measured distance is too large
Description : A pile is being driven with a drop hammer weighing 1800 kg and having a free fall of 1.00 m. If the penetration with last blow is 5 mm, the load carrying capacity of the pile, -according to the Engineering News formula, is (A) 100 tonnes (B) 50 tonnes (C) 20 tonnes (D) 10 tonnes
Last Answer : (D) 10 tonnes
Description : A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm
Last Answer : (C) 50 mm
Description : In the plate loading test for determining the bearing capacity of soil, the size of square bearing plate should be (A) Less than 300 mm (B) Between 300 mm and 750 mm (C) Between 750 mm and 1 m (D) Greater than 1 m
Last Answer : (B) Between 300 mm and 750 mm
Description : A 600 mm square bearing plate settles by 15 mm in plate load test on a cohesion-less soil under an intensity of loading of 0.2 N/ram². The settlement of a prototype shallow footing 1 m square under the same intensity of ... (A) 15 mm (B) Between 15 mm and 25 mm (C) 25 mm (D) Greater than 25 mm
Last Answer : Answer: Option B
Description : Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30
Last Answer : (B) 25
Description : If the viscosity of ground water is 1.00, the Slitcher's constant is 400, the effective size of soil particles in aquifer is 0.5 mm and hydraulic gradient is 1 in 80, the velocity of flow is (A) 0.25 m/day (B) 0.50 m/day (C) 1.00 m/day (D) 1.25 m/day
Last Answer : Answer: Option D
Description : The atmospheric pressure at sea level is (A) 103 kN/m2 (B) 10.3 m of water (C) 760 mm of mercury (D) All of these
Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm
Last Answer : Answer: Option C
Description : For 12 mm thick cement plastering 1 : 6 on 100 sq.m new brick work, the quantity of cement required, is (A) 0.200 m3 (B) 0.247 m3 (C) 0.274 m3 (D) 0.295 m
Last Answer : (C) 0.274 m3
Description : The expected out turn of 12 mm plastering with cement mortar is (A) 2.5 sq m (B) 4.0 sq m (C) 6.0 sq m (D) 8.0 sq m
Last Answer : (D) 8.0 sq m