Which of the following introduces an error of about 1 in 1000 if 20 m chain is used? (A) Length of chain 20 mm wrong (B) One end of the chain 0.9 m off the line (C) One end of chain 0.9 m higher than the other (D) All the above

Which of the following introduces an error of about 1 in 1000 if 20 m chain is used?
(A) Length of chain 20 mm wrong
(B) One end of the chain 0.9 m off the line
(C) One end of chain 0.9 m higher than the other
(D) All the above
by

1 Answer

Answer :

(D) All the above
by

Related questions

Measuring with a 30 m chain, 0.01 m too short, introduces (A) Positive compensating error (B) Negative compensating error (C) Positive cumulative error (D) Negative cumulative error

Description : Measuring with a 30 m chain, 0.01 m too short, introduces (A) Positive compensating error (B) Negative compensating error (C) Positive cumulative error (D) Negative cumulative error

Last Answer : (C) Positive cumulative error

If a 30 m chain diverges through a perpendicular distance d from its correct alignment, the error in length, is (A) (d²/60) m (B) (d²/30) m (C) (d²/40) m (D) (d/30) m

Description : If a 30 m chain diverges through a perpendicular distance d from its correct alignment, the error in length, is (A) (d²/60) m (B) (d²/30) m (C) (d²/40) m (D) (d/30) m

Last Answer : (A) (d²/60) m

The 10 mm markings on a levelling staff placed at 20 m are separated by (A) 1/1000 radian (B) 1/1500 radian (C) 1/2000 radian (D) 1/2500 radian

Description : The 10 mm markings on a levelling staff placed at 20 m are separated by (A) 1/1000 radian (B) 1/1500 radian (C) 1/2000 radian (D) 1/2500 radian

Last Answer : (C) 1/2000 radian

Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in temperature causes a tape to increase in length and the measured distance is too large (C) The straight distance between end points of a suspended tape is reduced by an amount called the sag correction (D) A 100 m tape of cross section 10 mm × 0.25 mm stretches about 10 mm under 5 kg pull

Description : Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in ... ) A 100 m tape of cross section 10 mm 0.25 mm stretches about 10 mm under 5 kg pull

Last Answer : (B) An increase in temperature causes a tape to increase in length and the measured distance is too large

While setting a plane table at a station it was found that the error in centering was 30 cm away from the ray of length 40 m drawn from the station. If the scale of the plan is 1 cm = 2 cm, the displacement of the end of the ray in plan from the true position will be (A) 0.02 cm (B) 0.15 cm (C) 0.2 cm (D) 0.1 cm

Description : While setting a plane table at a station it was found that the error in centering was 30 cm away from the ray of length 40 m drawn from the station. If the scale of the plan is 1 cm = 2 cm, the displacement of the end of ... true position will be (A) 0.02 cm (B) 0.15 cm (C) 0.2 cm (D) 0.1 cm

Last Answer : (B) 0.15 cm

The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg

Description : The tensile force required to cause an elongation of 0.045 mm in a steel rod of 1000 mm length and 12 mm diameter, is (where E = 2 × 106 kg/cm2 ) (A) 166 kg (B) 102 kg (C) 204 kg (D) 74 kg

Last Answer : (B) 102 kg

If 50 m point of a 100 m tape is 50 cm off line, and 50 m sections are straight, an error is generated equal to (A) 1/10,000 (B) 1/15,000 (C) 1/20,000 (D) 1/25,000

Description : If 50 m point of a 100 m tape is 50 cm off line, and 50 m sections are straight, an error is generated equal to (A) 1/10,000 (B) 1/15,000 (C) 1/20,000 (D) 1/25,000

Last Answer : (C) 1/20,000

Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of offset should be limited to (A) 14.14 m (B) 28.28 m (C) 200 m (D) None of these

Description : Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of ... should be limited to (A) 14.14 m (B) 28.28 m (C) 200 m (D) None of these

Last Answer : (B) 28.28 m

A standard steel tape of length 30 m and cross-section 15 × 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of steel tape is 2.2 × 106 kg/cm2 , the correction to be applied is (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these

Description : A standard steel tape of length 30 m and cross-section 15 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of ... (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these

Last Answer : (A) - 0.000909 m

Zero error of an instrument introduces.

Description : Zero error of an instrument introduces.

Last Answer : Zero error of an instrument introduces. (A) systematic error (B) random error (C) personal error (D) decimal error

The length of line measured with a chain was found to be 250m. Calculate the true length of line if i) The length was measured with 30 m chain and the chain was 10cm too long and ii) The length of chain was 30 m in the beginning and 30.10 m at the end of the work.

Description : The length of line measured with a chain was found to be 250m. Calculate the true length of line if i) The length was measured with 30 m chain and the chain was 10cm too long and ii) The length of chain was 30 m in the beginning and 30.10 m at the end of the work. 

Last Answer : Given Data: L = 30 m Measured Length = 250 m Solution: Case i) The length was measured with 30 m chain and the chain was 10cm too long L' = 30 + 0.1 = 30.1 m Correct Distance = (L'/L) x Measured Length ... = 30.05 m Correct Distance = (L'/L) x Measured Length  = (30.05/30) x 250  = 250.42 m

The length of line measured by 20 m chain was found to be 751 m. The chain was tested before start of measurement and was found correct. The chain was again tested after measurement and was found 6 cm too short. What shall be the correct length of line ?

Description : The length of line measured by 20 m chain was found to be 751 m. The chain was tested before start of measurement and was found correct. The chain was again tested after measurement and was found 6 cm too short. What shall be the correct length of line ?

Last Answer : Given Data: Standard length of chain (L)= 20m Measured Length (M.L.) = 751 m Error before start of measurement = 0.0 Error after measurement = 6 cm = 0.06 m To Find: Actual length or Correct length Solution: ... (L'/L)  = (751) x (19.97/20)  = 749.87 Correct length of line is 749.87 m

While measuring the distance between two points along upgrade with the help of a 20 m chain, the forward end of the chain is shifted forward through a distance (A) 20 (sin - 1) (B) 20 (cos - 1) (C) 20 (sec - 1) (D) 20 (cosec - 1)

Description : While measuring the distance between two points along upgrade with the help of a 20 m chain, the forward end of the chain is shifted forward through a distance (A) 20 (sin - 1) (B) 20 (cos - 1) (C) 20 (sec - 1) (D) 20 (cosec - 1)

Last Answer : (C) 20 (sec - 1)

To prevent movement of moisture from sub-grade to road pavement on embankments about 0.6 m to 1 m higher than water table, the thickness of cut off layer of coarse sand used, is (A) 15 cm (B) 20 cm (C) 30 cm (D) None of these

Description : To prevent movement of moisture from sub-grade to road pavement on embankments about 0.6 m to 1 m higher than water table, the thickness of cut off layer of coarse sand used, is (A) 15 cm (B) 20 cm (C) 30 cm (D) None of these

Last Answer : Answer: Option D

A portion of an embankment having a uniform up-gradient 1 in 500 is circular with radius 1000 m of the centre line. It subtends 180° at the centre. If the height of the bank is 1 m at the lower end, and side slopes 2:1, the earth work involved. (A) 26,000 m3 (B) 26,500 m3 (C) 27,000 m3 (D) 27,500 m

Description : A portion of an embankment having a uniform up-gradient 1 in 500 is circular with radius 1000 m of the centre line. It subtends 180° at the centre. If the height of the bank is 1 m at the lower end, and side slopes 2 ... earth work involved. (A) 26,000 m3 (B) 26,500 m3 (C) 27,000 m3 (D) 27,500 m

Last Answer : (D) 27,500 m3

A 20 m chain was found to be 10 cm too short after chaining 1000 m It was found to be 20 cm too short after chaining 1800 m. If the chain was correct before commencement of the work find the true distance.

Description : A 20 m chain was found to be 10 cm too short after chaining 1000 m It was found to be 20 cm too short after chaining 1800 m. If the chain was correct before commencement of the work find the true distance.  

Last Answer : Average error in chain for 1000 m length = (0 + 10) / 2 = 5 cm = 0.05 m too short True length up to 1000 m = (20 - 0.05) x 1000 / 20 = 997.5 m. Average error in chain from 1000 m to 1800 m length = (10 ... 1800 m length = (20 - 0.15) x 800 / 20 = 794.0 m. True distance = 997.5 + 794 = 1791.5 m.

A cantilever shaft having 50 mm diameter and a length of 300mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the static deflection of shaft in mm. A 0.144 B 0.244 C 0.344 D 0.444

Description : A cantilever shaft having 50 mm diameter and a length of 300mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the static deflection of shaft in mm. A 0.144 B 0.244 C 0.344 D 0.444

Last Answer : A 0.144

A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 3 . Determine the static deflection of the shaft in mm. a) 0.147 b) 0.213 c) 0.132 d) 0.112

Description : A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 3 . Determine the static deflection of the shaft in mm. a) 0.147 b) 0.213 c) 0.132 d) 0.112

Last Answer : a) 0.147

A cantilever of length 3 m carries a uniformly distributed load over the entire length.If the deflection at the free end is 40 mm,find the slope at the free end. a.0.0115 rad b.0.01777 rad c.0.001566 rad d.0.00144 rad

Description : A cantilever of length 3 m carries a uniformly distributed load over the entire length.If the deflection at the free end is 40 mm,find the slope at the free end. a.0.0115 rad b.0.01777 rad c.0.001566 rad d.0.00144 rad

Last Answer : b.0.01777 rad

A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2 , the deflection of the free end, is (A) 2 mm (B) 3 mm (C) 4 mm (D) 5 mm

Description : A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free  end. If the modulus of elasticity of the material is 0.2 × 106  N/mm2 , the deflection of the free end,  is  (A) 2 mm  (B) 3 mm  (C) 4 mm  (D) 5 mm

Last Answer : (D) 5 mm

A rolled steel joist is simply supported at its ends and carries a uniformly distributed load which causes a maximum deflection of 10 mm and slope at the ends of 0.002 radian. The length of the joist will be, (A) 10 m (B) 12 m (C) 14 m (D) 16 m

Description : A rolled steel joist is simply supported at its ends and carries a uniformly distributed load which  causes a maximum deflection of 10 mm and slope at the ends of 0.002 radian. The length of the  joist will be,  (A) 10 m  (B) 12 m  (C) 14 m  (D) 16 m 

Last Answer : (D) 16 m 

A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2 , the stresses developed are: (A) b = 10 N/mm2s = 20 N/mm2(B) b = 8 N/mm2s = 16 N/mm2(C) b = 6 N/mm2s = 12 N/mm2(D) b = 5 N/mm2s = 10 N/mm

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

A dumpy level was set up at the midpoint between two pegs A and B, 50 m apart and the staff readings at and were 1.22 and 1.06. With the level set up at , the readings at and were 1.55 and 1.37. The collimation error per 100 m length of sight is (A) 0.02 m inclined upwards (B) 0.04 m inclined downwards (C) 0.04 m inclined upward (D) None of these

Description : A dumpy level was set up at the midpoint between two pegs A and B, 50 m apart and the staff  readings at and were 1.22 and 1.06. With the level set up at , the readings at  and were 1.55 and ... upwards  (B) 0.04 m inclined downwards  (C) 0.04 m inclined upward  (D) None of these

Last Answer : (B) 0.04 m inclined downwards 

The enzyme DNA ligase (A) Introduces superhelical twists (B) Connects the end of two DNA chains (C) Unwinds the double helix (D) Synthesises RNA primers

Description : The enzyme DNA ligase (A) Introduces superhelical twists (B) Connects the end of two DNA chains (C) Unwinds the double helix (D) Synthesises RNA primers

Last Answer : Answer : B

Which statement is true about a cloud computing environment? A. It cannot be used to host location based applications. B. It enables users to access systems regardless of their location. C. It introduces latency as the servers are geographically dispersed. D. It can improve a web server response time by having servers closer to the end user.

Description : Which statement is true about a cloud computing environment? A. It cannot be used to host location based applications. B. It enables users to access systems regardless of their location. C. It introduces ... D. It can improve a web server response time by having servers closer to the end user.

Last Answer : It enables users to access systems regardless of their location.

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

. A 0.5 m high bed made up of a 1 mm dia glass sphere (density 2500 kg/m3 ) is to be fluidised by water (density 1000 kg/m3 ). If at the point of incipient fluidisation, the bed voidage is 40%, the pressure drop across the bed is (A) 4.4 KPa (B) 2.94 KPa (C) 3.7 KPa (D) None of these

Description : . A 0.5 m high bed made up of a 1 mm dia glass sphere (density 2500 kg/m3 ) is to be fluidised by water (density 1000 kg/m3 ). If at the point of incipient fluidisation, the bed voidage is 40%, the pressure drop across the bed is (A) 4.4 KPa (B) 2.94 KPa (C) 3.7 KPa (D) None of these

Last Answer : (A) 4.4 KPa

The lower water cement ratio in concrete, introduces (A) Smaller creep and shrinkage (B) Greater density and smaller permeability (C) Improved frost resistance (D) All the above

Description : The lower water cement ratio in concrete, introduces (A) Smaller creep and shrinkage (B) Greater density and smaller permeability (C) Improved frost resistance (D) All the above

Last Answer : Answer: Option D

Probable accidental error in precise levelling as recommended by International Geodetic Association should not exceed (where k is in kilometers.) (A) ± 0.1 k mm (B) ± 0.5 k mm (C) ± 1 k mm (D) ± 5 k mm

Description : Probable accidental error in precise levelling as recommended by International Geodetic Association should not exceed (where k is in kilometers.) (A) ± 0.1 k mm (B) ± 0.5 k mm (C) ± 1 k mm (D) ± 5 k mm

Last Answer : (C) ± 1 k mm

Probable systematic error in precise levelling as recommended by International Geodetic Association should not exceed (where is in kilometers.) (A) ± 0.1 k mm (B) ± 0.2 k mm (C) ± 0.1 k (D) 0.2 k mm

Description : Probable systematic error in precise levelling as recommended by International Geodetic Association should not exceed (where is in kilometers.) (A) ± 0.1 k mm (B) ± 0.2 k mm (C) ± 0.1 k (D) 0.2 k mm

Last Answer : (D) 0.2 k mm

Pick up the correct statement from the following: (A) With both handles in his left hand, the chain man throws out the chain with his right hand and the second chain man assists him to free it from knots (B) The follower of the chaining operation should be more experienced than the leader (C) At the end of the tenth chain length, the two chain men meet and the ten arrows are handed over to the leader (D) All the above

Description : Pick up the correct statement from the following: (A) With both handles in his left hand, the chain man throws out the chain with his right hand and the second chain man assists him to free it from ... the two chain men meet and the ten arrows are handed over to the leader (D) All the above

Last Answer : (D) All the above

A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free enD. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. A. 575B. 625 C. 525 D. 550

Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free enD. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. A. 575B. 625 C. 525 D. 550

Last Answer : A. 575

A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Determine the frequency of transverse vibrations of the shaft. a) 31 b) 35 c) 37 d) 41

Description : A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Determine the frequency of transverse vibrations of the shaft. a) 31 b) 35 c) 37 d) 41

Last Answer : d) 41

A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. a) 575 b) 625 c) 525 d) 550

Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. a) 575 b) 625 c) 525 d) 550

Last Answer : a) 575

A cantilever of length 3 m carries two point loads of 2 KN at the free end and 4KN at a distance of 1m from the free end .What is the deflection at the free end? Take E= 2×105 N/mm2and I= 108 mm4. a.2.56 mm b.3.84 mm c.1.84 mm d.5.26mm

Description : A cantilever of length 3 m carries two point loads of 2 KN at the free end and 4KN at a distance of 1m from the free end .What is the deflection at the free end? Take E= 2×105 N/mm2and I= 108 mm4. a.2.56 mm b.3.84 mm c.1.84 mm d.5.26mm

Last Answer : c.1.84 mm

Tommy Hilfiger introduces a new line of men's ties targeted at men who are very statu s - conscious. In keeping with this assessment, department stores selling the ties should A)charge a price based mostly on their cost. B)charge prices consistent with their existing ties. C)discount the ties to move them rapidly. D)use the price variable symbolically.

Description : Tommy Hilfiger introduces a new line of men's ties targeted at men who are very statu s - conscious. In keeping with this assessment, department stores selling the ties should A)charge a price ... their existing ties. C)discount the ties to move them rapidly. D)use the price variable symbolically.

Last Answer : D)use the price variable symbolically.

A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm

Description : A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm

Last Answer : a. 5.4 mm

The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

If is the difference in height between end points of a chain of length , the required slope correction is (A) h²/2l (B) h/2l (C) h²/l (D) 2h²/2l

Description : If is the difference in height between end points of a chain of length , the required slope correction is (A) h²/2l (B) h/2l (C) h²/l (D) 2h²/2l

Last Answer : (A) h²/2l

Pick up the correct statement from the following: (A) The length of the brass handle is included in the length of chain (B) The handles are on swivel joints to prevent twisting of the chain (C) The fifth tag from either end of the chain is numbered 5 (D) All the above

Description : Pick up the correct statement from the following: (A) The length of the brass handle is included in the length of chain (B) The handles are on swivel joints to prevent twisting of the chain (C) The fifth tag from either end of the chain is numbered 5 (D) All the above

Last Answer : (D) All the above

The diameter of the Vicat plunger is 10 mm and its length varies from (A) 20 mm to 30 mm (B) 30 mm to 40 mm (C) 40 mm to 50 mm (D) 50 mm to 60 mm

Description : The diameter of the Vicat plunger is 10 mm and its length varies from (A) 20 mm to 30 mm (B) 30 mm to 40 mm (C) 40 mm to 50 mm (D) 50 mm to 60 mm

Last Answer : Answer: Option C

The length of Seconds Pendulum is a.992 mm b.999 mm c.994 mm d.995 mm e.1000 mm

Description : The length of Seconds Pendulum is a.992 mm b.999 mm c.994 mm d.995 mm e.1000 mm

Last Answer : c. 994 mm

The inductance of a long solenoid of length 1000 mm wound uniformly with 3000 turns on a cylindrical paper

Description : The inductance of a long solenoid of length 1000 mm wound uniformly with 3000 turns on a cylindrical paper tube of 60 mm diameter is  (A) 3.2 µH (B) 3.2 mH (C) 32.0 mH (D) 3.2 H

Last Answer : The inductance of a long solenoid of length 1000 mm wound uniformly with 3000 turns on a cylindrical paper tube of 60 mm diameter is 32.0 mH

An aggregate which passes through 25 mm I.S. sieve and is retained on 20 mm sieve, is said to be flaky if its least dimension is less than (A) 22.5 mm (B) 18.5 mm (C) 16.5 mm (D) 13.5 m

Description : An aggregate which passes through 25 mm I.S. sieve and is retained on 20 mm sieve, is said to be flaky if its least dimension is less than (A) 22.5 mm (B) 18.5 mm (C) 16.5 mm (D) 13.5 mm

Last Answer : Answer: Option D

A shaft 9 m long is subjected to a torque 30 t-m at a point 3 m distant from either end. The reactive torque at the nearer end will be (A) 5 tonnes metre (B) 10 tonnes metre (C) 15 tonnes metre (D) 20 tonnes metre

Description : A shaft 9 m long is subjected to a torque 30 t-m at a point 3 m distant from either end. The reactive torque at the nearer end will be (A) 5 tonnes metre (B) 10 tonnes metre (C) 15 tonnes metre (D) 20 tonnes metre

Last Answer : (D) 20 tonnes metre

If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an axial pull of 3000 kg, the stress developed, is (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Description : If a steel rod of 20 mm diameter and 5 metres long elongates by 2.275 mm when subjected to an  axial pull of 3000 kg, the stress developed, is  (A) 9.5541 kg/cm2 (B) 95.541 kg/cm2 (C) 955.41 kg/cm2 (D) 9554.1 kg/cm

Last Answer : (C) 955.41 kg/cm2

Referring of given figure, pick up the correct statement from the following: (A) The total length of centre line of four walls is 20 m (B) Length of long wall out-to-out is 6.80 m (C) Length of short walls in-to-in is 3.20 m (D) All the above

Description : Referring of given figure, pick up the correct statement from the following: (A) The total length of centre line of four walls is 20 m (B) Length of long wall out-to-out is 6.80 m (C) Length of short walls in-to-in is 3.20 m (D) All the above

Last Answer : (D) All the above

A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the force exerted by the jet on the plate would be in the range a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Description : A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the ... a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Last Answer : a. 15 - 20 kg

The minimum range for sliding the focusing lens in the internal focusing telescope for focusing at all distances beyond 4 m is (A) 5 mm (B) 10 mm (C) 15 mm (D) 20 mm

Description : The minimum range for sliding the focusing lens in the internal focusing telescope for focusing at all distances beyond 4 m is (A) 5 mm (B) 10 mm (C) 15 mm (D) 20 mm 

Last Answer : (D) 20 mm