Describe the mechanism of chip formation during metal cutting with the help of sketch.

Describe the mechanism of chip formation during metal cutting with the help of sketch.
by

1 Answer

Answer :

Mechanism of chip formation : In Fig. the tool is considered stationary, and the work piece moves to the right. The metal is severely compressed in the area in front of the cutting tool. This causes high temperature shear and plastic flow if the metal is ductile. When the stress in the work piece just ahead of the cutting tool reaches a value exceeding the ultimate strength of the metal, particles will shear to form a chip element which moves up along the face of the work. The outward or shearing movement of each successive element is arrested by work hardening and the movement transferred to the next element. The process is repetitive and a chip is formed. 

image

by

Related questions

Write type of chip formed with following factors. (i) High rake angle (ii) High cutting speed (iii) Small depth of cut (iv) Low cutting speed (v) Large depth of cut (vi) Low rake angle

Description : Write type of chip formed with following factors. (i) High rake angle (ii) High cutting speed (iii) Small depth of cut (iv) Low cutting speed (v) Large depth of cut (vi) Low rake angle

Last Answer : (i) High rake angle : Continuous chips (ii) High cutting speed : Continuous chips (iii) Small depth of cut : Continuous chips (iv) Low cutting speed :Continuous chips with built up edge (v) ... cut : Continuous chips with built up edge (vi) Low rake angle :Continuous chips with built up edge

Define cutting speed and feed in metal cutting process.

Description : Define cutting speed and feed in metal cutting process.

Last Answer : Cutting Speed: Cutting speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute).  Feed : Feed is defined as the distance the tool travels during one revolution of the part. 

Describe the single point cutting tool with nomenclature.

Description : Describe the single point cutting tool with nomenclature. 

Last Answer : Terminology used in Single Point Cutting Tool: Size: It is determined by the width of shank, height of shank and overall length. Shank: Shank is main body of a tool. It is held in a holder. Flank : ... If the slope is away from the cutting edge, it is positive side rake angle. OR

Describe with neat sketch specification of lathe machine.

Description : Describe with neat sketch specification of lathe machine.

Last Answer : 1. The height of the centers measured from the lathe bed. 2. The swing diameter over bed. This is the largest diameter of work that will revolve without touching the bed and is twice the height of ... 6. The length of bed. This indicates the approximate floor space occupied by the lathe. 

Write the suitable cutter for carrying following operations on milling machine (i) Gear Tooth (ii) Parting off (iii) Keyway (iv) V-grooves (v) Rounding of corner (vi) Cutting of narrow slot and groove

Description : Write the suitable cutter for carrying following operations on milling machine (i) Gear Tooth (ii) Parting off (iii) Keyway (iv) V-grooves (v) Rounding of corner (vi) Cutting of narrow slot and groove

Last Answer : (i) Gear Tooth : Form milling cutter, Cylindrical type or End mill type, Gear cutter. (ii) Parting off: Slitting Cutter (iii) Keyway : Staggered teeth side milling cutter, End mill cutter, key ... milling cutter. Selection of a cutter depends upon type and size of slot or groove to be produced. 

Explain the nomenclature of a single point cutting tool.

Description : Explain the nomenclature of a single point cutting tool.

Last Answer : 1. Back Rake Angle: Back rake angle is the angle between the face of the single point cutting tool and a line parallel with base of the tool measured in a perpendicular plane through the side cutting ... the side of the shank. It is responsible for turning the chip away from the finished surface. 

State any four properties of cutting fluid.

Description : State any four properties of cutting fluid.

Last Answer : Properties of cutting fluid:  1. High heat absorption 2. Good lubricating qualities to produce low coefficient of friction 3. Low viscosity to permit free flow of liquid 4. Non-corrosive to the ... to the skin of operator 8. Transparency so that the cutting action of the tool may be observed

Explain hot chamber die casting process with neat sketch.

Description : Explain hot chamber die casting process with neat sketch.

Last Answer : Hot chamber die casting : In a hot chamber submerged plunger-type machine, the plunger operates in one end of a gooseneck casting which is submerged in the molten metal. With the plunger in ... . Heating is continued throughout the operation to keep the molten metal sufficiently liquid.

Explain sweep mounding with sketch

Description : Explain sweep mounding with sketch

Last Answer : Sweep mounding : Sweep mouldings are employed for moulding parts whose shape is that of a surface of revolution. A base 1 and spindle 2 is well placed in the foundry floor. The sand is filled in and rammed until ... . The gate is then cut and the mould is ready for pouring as shown in fig(c)

Describe thermoplastic with its properties.

Description : Describe thermoplastic with its properties.

Last Answer : Thermoplastic: These are composed of linear and long chain straight or slightly branched molecules. They can be resoftened and remelted by application of heat and pressure. The materials which can be ... temperature as they tend to soft under heat 7) Usually soluble in some organic solvents.

Describe the normalizing process with its purpose.

Description : Describe the normalizing process with its purpose. 

Last Answer : Normalizing: Normalizing is the heat treatment which involves heating of the given steel to austenite temperature range holding it and there after cooling to room temperature at slow rate of cooling, ... To obtain required mechanical properties. To relieve internal stresses in some cases. 

Describe plain carbon steel with its application.

Description : Describe plain carbon steel with its application.

Last Answer : Plain carbon Steel: Plain-carbon steel or Carbon steel is a metal alloy. It is a combination of two elements, iron and carbon. Other elements are present in quantities too small to affect its ... ball bearings, mandrels, cutters, files, wire drawing dies, reamers, and metal cutting saws, etc. 

Describe full annealing process with its significance.

Description : Describe full annealing process with its significance.

Last Answer : Full annealing Process: In full annealing process the steel workpiece is heated to about 30 to 500 above the critical temperature AC3, is held there until the temperature of the workpiece is ... structure, soften the metal and relieves the internal stresses previously set up in the metal.

Describe the steps in sand casting process.

Description : Describe the steps in sand casting process.

Last Answer : Following steps are used in the casting process; 1. Pattern Making: Patterns are the replica of casting. Patterns are manufactured using wood, metals, wax, plaster of Paris etc. For preparation of ... appears at parting line of mould. 5. Testing of Casting: Test the casting for various defects.

Describe Shell Molding Process with applications.

Description : Describe Shell Molding Process with applications.

Last Answer : Shell Moulding: It is a process in which the sand mixed with a thermosetting resin is allowed to come into contact with a heated metallic pattern plate, so that a thin and a strong shell of mould is ... 6. Gear blanks 7. Small crank shafts 8. Refrigerator valve plate 9. Chain seat bracket

Enlist different types of chips formed during machining

Description : Enlist different types of chips formed during machining

Last Answer : Different types of chips: 1. Discontinuous or segmental chips 2. Continuous chips 3. Continuous chips with built-up edge (BUE) 4. Non homogeneous chip

Use suitable pattern allowance to compensate the shrinkage problem during casting process.

Description : Use suitable pattern allowance to compensate the shrinkage problem during casting process.

Last Answer : Shrinkage Allowance: As metal solidifies and cools, it shrinks and contracts in size. To compensate for this, a pattern is made larger than the finished casting by means of a shrinkage or ... are reduced by gates & risers Solid contraction can be reduced by providing more allowance on pattern 

Choose proper machine tool and explain operation method for the following: (i) Producing a hole (ii) Finishing previously drilled hole

Description : Choose proper machine tool and explain operation method for the following: (i) Producing a hole (ii) Finishing previously drilled hole

Last Answer : MACHINE TOOL : Drilling Machine (i) Producing a hole: Drilling operation (Fig 1 mark ,explanation 2 mark) : It is an operation of producing a circular hole in a work piece by forcing a drill against ... is held in the tailstock and it is fed into the hole in the similar way as for drilling.  

Use suitable pattern for producing circular part in foundry.

Description : Use suitable pattern for producing circular part in foundry.

Last Answer : Sweep pattern: Sweep patterns are used for forming large circular moulds of symmetric kind by revolving a sweep attached to a spindle as shown in Fig. Actually a sweep is a template of wood or metal and is ... use of a central pivot. A segment pattern for a wheel rim is shown in fig. 

Identify the causes of generating blow holes and misrun in casting and also suggest remedies to avoid them.

Description : Identify the causes of generating blow holes and misrun in casting and also suggest remedies to avoid them.

Last Answer : Answer: 1) Blowholes: Causess: Excessive moisture in the sand, or when permeability of sand is low, sand grains are too fine, sand is rammed too hard, or when venting is insufficient. ... gating Remedies : Adjust proper pouring temperature Modify design Modify gating system. 

Apply proper heat treatment process for manufacturing connecting rod of an engine.

Description : Apply proper heat treatment process for manufacturing connecting rod of an engine. 

Last Answer : Answer: The connecting rod may either be cast or forged when created and may also include allowable secondary alloy elements.  The normalizing step includes heating a rough connecting rod to ... , not throughout the entire rod, but instead only where high hardness is required functionally.

Identify the properties of material used for connecting rod with justification

Description : Identify the properties of material used for connecting rod with justification

Last Answer : Answer:  1. There are some materials that are commonly used in connecting rods such as alloys of steel, aluminum and titanium. Mostly connecting rods are made by forged steel. It is widely use ... times lighter than carbon steel. It is because density of Al360 is very less compared to carbon steel 

Explain the taper turning method by swiveling the compound rest method.

Description : Explain the taper turning method by swiveling the compound rest method. 

Last Answer : Taper turning by swiveling compound rest: Figure below shows the arrangement made for the taper turning by swiveling the compound rest. This method employs the principle of turning taper by rotating the ... is controlled by hand. Following formula is used for calculation of taper turning.  

State four operations performed by the lathe.

Description : State four operations performed by the lathe.

Last Answer : Operations performed on lathe machine  1. Facing, 2. Plain turning, 3. Step turning, 4. Taper turning, 5. Drilling, 6. Reaming, 7. Boring, 8. Undercutting, 9. Threading, 10. Knurling

List the main four parts of a lathe

Description : List the main four parts of a lathe 

Last Answer : Parts of Lathe Machines are as follows :  1. Bed 2. Head stock 3. Carriage 4. Main spindle 5. Tailstock 6. Tool post 7. Compound Rest 8. Cross slide 9. Saddle.

Define the term casting.

Description : Define the term casting.

Last Answer : Casting means pouring molten metal poured into a refractory mold cavity and allows it to solidify. The solidified object is taken out from the mold either by breaking or taking the mold apart. The solidified object is called casting. The technique followed in method is known as casting process. 

State two purposes of heat treatment.

Description : State two purposes of heat treatment.

Last Answer : Purposes of Heat treatment:  Improve machinability Relieve the internal stresses Improve mechanical properties such as ductility, strength, hardness, toughness, etc. Change in grain ... corrosion Modify electrical and magnetic properties. Change in chemical composition Remove gases

List four types of cast iron.

Description : List four types of cast iron.

Last Answer : Types of Cast Iron:  1. Gray Cast Iron 2. White Cast Iron 3. Malleable Cast Iron 4. Ductile Cast Iron 5. Nodular cast iron 6. Meehanite cast iron

Explain properties and applications of GRP/CRP and CRP composites.

Description : Explain properties and applications of GRP/CRP and CRP composites.

Last Answer : Properties of GRP( Glass Reinforced Plastic)/CRP ( Carbon Reinforced Plastic):  1.High corrosion resistance: Offering exceptional corrosion resistance, GRP/CRP is highly tolerant of the most aggressive of ... drone 8. Lightweight poles such as tripod legs etc 9. Denstistry

Explain the significance of gating system in casting process with the sketches.

Description : Explain the significance of gating system in casting process with the sketches.

Last Answer : Significance of Gating system in casting process: The term gating system refers to all passageways through which the molten metal passes to enter the mold cavity. It provides continuous, uniform feed of ... walls. It prevents slag, sand and other foreign particles from entering the mould.

Explain match plate pattern with its significance.

Description : Explain match plate pattern with its significance.

Last Answer : Match plate pattern with significance: In Match plate pattern the cope and drag patterns along with the gating and the risering are mounted on a single matching metal or wooden plate on either side ... . They are expensive but since they increase productivity, the additional cost is justified.  

State the effects of alloying elements on properties of steel.

Description : State the effects of alloying elements on properties of steel.

Last Answer : Effects of Alloying Element on steel:(Any 04 - 01 Mark each) 1) Nickel: i) It improves Toughness ii) It improves Tensile Strength iii) It improves Ductility iv) It improves Corrosion Resistance ... Impact Strength iii) It improves Fine Grain Growth iv) It is also called as Columbium

Discuss the properties and applications of Ti-6Al-4V titanium alloy.

Description : Discuss the properties and applications of Ti-6Al-4V titanium alloy.

Last Answer : Properties of Ti-6Al-4V 1. The high strength 2. Low weight ratio 3. Outstanding corrosion resistance 4. Good machinability 5. Excellent mechanical properties Applications: Ti6Al4V is ... as implants and prosthesis 3. Marine applications 4. Chemical industry 5. Gas turbines Powder

Explain the lathe specification or size of lathe.

Description : Explain the lathe specification or size of lathe.

Last Answer : The size of a lathe is expressed or specified by the following items and illustrated in Fig. The height of the centers measured from the lathe bed. The swing diameter over bed. This is the ... is the maximum diameter of bar stock that will pass through hole of the headstock spindle. 

State any four objectives of heat treatment.

Description : State any four objectives of heat treatment.

Last Answer : Following are the objectives of Heat Treatment: 1. To improve machinability 2. To improve mechanical properties e.g. tensile strength, ductility, hardness, shock resistance, resistance to corrosion ... metal. 9. Homogenize the structure. 10. Change the chemical composition of metal components

List any four drilling machine used in industrial sector.

Description : List any four drilling machine used in industrial sector.

Last Answer : Classification of drilling machine: 1. Portable drilling machine 2. Bench drilling machine 3. Sensitive drilling machine 4. Upright or column drilling machine 5. Radial drilling machine 6. ... machine 8. Vertical drilling machine 9. Automatic drilling machine 10. Deep hole drilling machine

Define machine tool.

Description : Define machine tool.

Last Answer : A machine tool is a power driven machine form making articles of a given shape , size and accuracy( according to blueprints) by removing metal from workpieces in the form of chips. Most machine tools perform the ... one or both of these( 1 and 2) 4. Provide a feeding motion to one of these.

State the need of advanced material in making of automobile components.

Description : State the need of advanced material in making of automobile components.

Last Answer : The general finding highlights the need for developing material systems methodology and for approaching research issues in terms of material life cycles.  Improved materials and material ... Modeling of material system. Materials system research, Lightweight material for body structure.

Write two need of advanced material in Automobile Sector.

Description : Write two need of advanced material in Automobile Sector.

Last Answer : Answer:  The general finding highlights the need for developing material systems methodology and for approaching research issues in terms of material life cycles.  Improved materials and material ... material system. Materials system research, Lightweight material for body structure.

Describe push rod overhead valve operating mechanism with neat sketch.

Description : Describe push rod overhead valve operating mechanism with neat sketch.

Last Answer : Push rod Overhead valve operating mechanism (OHV 4 -S engine): An overhead valve engine (OHV engine) is an engine in which the valves are placed over the cylinder head. The camshaft drive-chain ... . Overhead valve arrangement makes the engine slightly shorter than overhead camshaft.   OR  

Describe with schematic sketch working of Vacuum operating clutch mechanism

Description : Describe with schematic sketch working of Vacuum operating clutch mechanism

Last Answer : Fig:- Vacuum Operated Clutch linkage -Vacuum operated clutch linkage operated by engine Vacuum created during suction stroke -It consists of vacuum reservoir tank connected to engine ... piston & plunger which further connected to release fork & release bearing as shown in fig

Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a ... explanation of A (c) A is true but R is false (d) A is false but R is true

Last Answer : (c) A is true but R is false

If you saw the potato chip sketch on Saturday Night Live this weekend, what did you think of it?

Description : If you saw the potato chip sketch on Saturday Night Live this weekend, what did you think of it?

Last Answer : I thought that entire episode was horrible. I expected more from Blake Lively.

Describe with sketch the surface treatment process used to built-up worn out metal components of automotive engines.

Description : Describe with sketch the surface treatment process used to built-up worn out metal components of automotive engines.

Last Answer : Metal spraying is to build-up worn out metal components of automotive engines.   Metal Spraying of metalizing literally means to treat with or coat with a metal or metallic compound. Metalizing as ... being coated, by compressed air. A sectional view of metal spraying gun is shown in fig.  

General mechanism of size reduction in intermediate and fine grinder is by (A) Cutting action (B) Compression (C) Compression and tearing (D) Impact and attrition

Description : General mechanism of size reduction in intermediate and fine grinder is by (A) Cutting action (B) Compression (C) Compression and tearing (D) Impact and attrition

Last Answer : (D) Impact and attrition

Draw a sketch of rack and pinion steering gear mechanism. Explain its working.

Description : Draw a sketch of rack and pinion steering gear mechanism. Explain its working.

Last Answer : Working: The rotary motion of the steering wheel is transmitted to the pinion of the steering gear through universal joints. The pinion is mesh with a rack. The circular motion of the pinion is ... relayed through the ball joints and the rods to the stub axles for the wheels to be steered.  

Explain the working of Ackerman steering gear mechanism with neat sketch.

Description : Explain the working of Ackerman steering gear mechanism with neat sketch.

Last Answer : Working: The whole mechanism of Ackerman Steering gear is on the back of the front wheels. The Ackerman steering gear consists of turning pairs The slotted links AM and BH are attached ... each end. The steering is affected by moving CD to the right or left of its nominal position. 

Draw the neat sketch of overhead valve operating mechanism and explain its working.

Description : Draw the neat sketch of overhead valve operating mechanism and explain its working.

Last Answer : Overhead valve mechanism: Figure shows the valve mechanism to operate the valve when it is in the cylinder head (in I and F head design). This type of mechanism requires two additional moving parts the push ... close. A spring (attached to the valve) returns the valve to its seated position.   

Explain working of over head valve mechanism with neat sketch.

Description : Explain working of over head valve mechanism with neat sketch.

Last Answer : Overhead valve mechanism: Figure shows the valve mechanism to operate the valve when it is in the cylinder head (in I and F head design). This type of mechanism requires two additional moving parts the ... to close. A spring (attached to the valve) returns the valve to its seated position.  

Explain slotted time quick return mechanism with neat sketch.

Description : Explain slotted time quick return mechanism with neat sketch. 

Last Answer : The slotted lever quick return mechanism is illustrated in Figs. a and b The crank AB (of adjustable length R) rotates with a uniform angular speed. The crank pin B is in the shape of a die block ... Fig. (b)) and the return stroke is completed in less time which is proportional to angle β.