Describe with schematic sketch working of Vacuum operating clutch mechanism

Describe with schematic sketch working of Vacuum operating clutch mechanism
by

1 Answer

Answer :

image

Fig:- Vacuum Operated Clutch linkage


-Vacuum operated clutch linkage operated by engine Vacuum created during suction stroke

-It consists of vacuum reservoir tank connected to engine inlet manifold through non return valve.

-Reservoir connected to solenoid valve which operated by battery and switch in the gear lever.

-Control valve attached to vacuum cylinder consist of piston & plunger which further connected to release fork & release bearing as shown in fig

by

Related questions

Describe the working of motorcycle clutch with neat sketch.

Description : Describe the working of motorcycle clutch with neat sketch.

Last Answer : Working : While the flywheel is rotating the pressure plates rotate and press against the friction plate. This causes the friction plates and thus the clutch shaft to rotate as well. When the pedal is ... they are not fully pressed by pressure plates. Thus the shaft also stops rotation. 

Describe with neat sketch construction details of clutch plate.

Description : Describe with neat sketch construction details of clutch plate.

Last Answer : Fig:- Single Plate Clutch Constructional details : It consist of steel plate with a splined central hub. Annular friction facing are attached to the steel plates by rivets. Special resins are ... are similar type of slots in each of the two plates situated on either side of the hub flang 

Describe with schematic diagram working of constant mesh gearbox

Description : Describe with schematic diagram working of constant mesh gearbox

Last Answer : -In constantmesh gearbox all the gears on the mainshaft are constantly mesh with layshaft gear & freely rotate on mainshaft. -When the clutch is in engaed position & gears ... than direction of mainshaft becomes reverse & reverse gear ratio obtained which is near about 3:1

Describe with neat sketch working of full floating type.

Description : Describe with neat sketch working of full floating type.

Last Answer : Fig:- full floating Rear axle Explanation: The figure shows the full floating axle. The wheel is on the axle casing. Two roller bearings are between the wheel and axle casing. ... supported by the wheel and the axle casing. Fully floating rear axle is used in heavy commercial vehicles 

Describe working of continuously variable transmission with suitable sketch

Description : Describe working of continuously variable transmission with suitable sketch

Last Answer : A Vario-drive consists of two set of split pulleys - drive and driven pulley and drive belt between the pulleys. The drive pulley is fitted to the crankshaft and driven to rear wheel ... driven pulley gets decreased thus a reduced drive ratio between the driven and drive pulleys is obtained.

What are the different materials used for clutch lining? State its necessity.

Description : What are the different materials used for clutch lining? State its necessity.

Last Answer : Material:- 1. Leather 2. Cork 3. Fabric 4. Asbestos 5. Reybestos and Ferodo 6. Non- asbestos clutch lining material Necessity:- 1. It should have good anti fading characteristic 2. It should have longer life. 3. It should be nonpolluting. 4. It should have lesser cost

Compare dry clutch & wet clutch on basis of

Description : Compare dry clutch & wet clutch on basis of

Last Answer : Parameter Dry Clutch Wet Clutch Construction When the clutch is operated dry i.e. without oil, it is called as a dry clutch. When the clutch is operated in an oil bath, it is ... , Bus, Truck etc. Multi-plate clutch is used in motor cycles, racing cars, heavy duty vehicles.

Write a function of Automobile Clutch

Description : Write a function of Automobile Clutch

Last Answer : To engage and disengage the engine power from transmission as required when the vehicle is to stop by applying brakes. To facilitate the easy gear shifting from 1st to 2nd or from ... in transmission by providing suitable means. To reduce the vibrations during high speed power transmission

Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Description : Describe with sketch construction of tubeless tyre & state its two advantages over Tube type

Last Answer : This type of tyre does not need separate tube, instead the air under pressure is filled in the tyre for which purpose a non return valve is fitted to the rim. The tyre is directly mounted on the ... safety:- in case of puncture air defuses slowly which provide safety to driver as well as other.

Describe with sketch the method of lubrication of synchromesh gearbox

Description : Describe with sketch the method of lubrication of synchromesh gearbox

Last Answer : Splash lubrication system : The splash lubricating system is simple to manufacture and implement in synchromesh gearbox. Lay shaft gear revolutions splash up lubricant from the sump to provide adequate ... the gear box 3. Selector mechanism is lubricated by thin machine oil/engine oil

Illustrate with the sketch functional relationship of major components of power transmission system

Description : Illustrate with the sketch functional relationship of major components of power transmission system

Last Answer : Fig:- major assembly & There location on chassis frame 1. Chassis Frame: - it is backbone of vehicle. all sub systems mounted on chassis frame 2. Engine:-it is heart of vehicle ... 7. Wheels & Tyres:-it carry weight of vehicle , transmit driving thrust, absorb road shocks

Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Description : Sketch a layout of Front Engine Rear Wheel Drive vehicle & label the major parts

Last Answer : Fig:- Front EngineRear Wheel Drive Vehicle Layout

Explain construction of Hotchkiss drive with suitable sketch

Description : Explain construction of Hotchkiss drive with suitable sketch

Last Answer : Hotchkiss drive: Explanation: Construction:- This drive is invented by Albert Hotchkiss. In the Hotchkiss drive two universal joints are used one at front and second at rear end of propeller shaft ... torque reaction leaf spring deflects. It is used in heavy duty vehicles like bus and trucks.

Explain any one type of Frame section with neat sketch

Description : Explain any one type of Frame section with neat sketch

Last Answer : four section of chassis frame with their merits Channel Section: The channel section is used for making the long members of the frame. It provides a good resistance to bending. It is poor ... to torsional loading (twisting) and they shall not use in the cases where torsion is dominant. 

Describe a method of lubrication for rear axle assembly of the truck.

Description : Describe a method of lubrication for rear axle assembly of the truck.

Last Answer : The combined lubrication system is very important in the final drive axle, where load and or speed transferred are high, the combination of splash and force feed of lubricant is delivered to ... trickles down due to gravity into the sump, where it is collected again and the cycle repeats  

Describe advantages of torque converter over manual transmission system

Description : Describe advantages of torque converter over manual transmission system

Last Answer : Advantages of torque converter : 1. Torque converter varies gear ratio in the range of 3:1 to 1:1 in infinite no. of stages which gives uniform acceleration 2. No need of operating ... avoiding manual interference of gear changing. 4. It allows starting & stopping vehicle without any difficulty.

Distinguish among radial ply, cross ply & belted bias types tyres

Description : Distinguish among radial ply, cross ply & belted bias types tyres

Last Answer : Sr. No. Radial ply tyre Cross ply tyre Belted bias Type  1 Plies are running radially straight from bead to bead Piles are running diagonally opposite from bead to bead. The basic construction is ... tyre. Costlier than radial ply & cross ply tyre 8

In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Description : In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Last Answer : Reason of synchromesh gear box preferred over constant mesh gearbox  1) No need of double declutching as in case of constant mesh gearbox.  2) Smooth engagement of higher gears due to synchromesh ... lay shaft gears to main shaft gear and then to the main shaft through synchronizer device 

Explain the concept of Aspect Ratio.

Description : Explain the concept of Aspect Ratio.

Last Answer : Aspect Ratio: The aspect ratio of a tyre is the height of the tyre sidewall expressed as a percentage of the tyre’s width. For example, a tyre with a profile/aspect ratio of 65, is a tyre whose height is equal to 65% of its width. 

State the function of Slip joint & universal Joint

Description : State the function of Slip joint & universal Joint

Last Answer : 1)Slip joint Functions: When the rear wheel comes across a bump, the spring compresses or expands as the differential with the rear axle housing and the wheel moves up and down. This ... drive changes continuously and universal joint allows transmission of power and rotary motion at a varied angle

State the purpose of Transfer case

Description : State the purpose of Transfer case

Last Answer : 1. Transfer case is used in four wheel drive vehicle along with main gearbox to transmit torque and power to the rear axle. 2. It enables the driver to drive the vehicle in two wheel drives on ... applications.  3. It also enables to drive the vehicle in high gear or low gear whenever required.

Enlist different material used in Frames

Description : Enlist different material used in Frames

Last Answer : 1) Mild steel 2) Carbon steel 3) Nickel alloy steel 4) Aluminum alloy. 02 

State the necessity of Frame in Automobile.

Description : State the necessity of Frame in Automobile.

Last Answer : 1. To support the body and chassis components such as engine, gear box, axles, suspension system, braking system etc. 2. To withstand different types of loads acting on it

Describe working of centrifugal clutch with neat sketch.

Description : Describe working of centrifugal clutch with neat sketch.

Last Answer : Centrifugal clutch-  Working of Centrifugal Clutch: Centrifugal clutch works on the principle of centrifugal force. When the engine is started, the speed of the driving shaft is less, so the centrifugal force ... disengaged at low speed. The stop H limits the amount of centrifugal force.

Draw the sketch of multiplate clutch and describe its construction and working.

Description : Draw the sketch of multiplate clutch and describe its construction and working. 

Last Answer : Multi - Plate clutch consists of a number of clutch plates instead of only one clutch plate like in the Single plate clutch. Friction surface also increased because of a number of clutch plates. Because of number of friction ... T = n.μ.W.R where R = Mean radius of the friction surfaces

Draw the neat sketch of overhead valve operating mechanism and explain its working.

Description : Draw the neat sketch of overhead valve operating mechanism and explain its working.

Last Answer : Overhead valve mechanism: Figure shows the valve mechanism to operate the valve when it is in the cylinder head (in I and F head design). This type of mechanism requires two additional moving parts the push ... close. A spring (attached to the valve) returns the valve to its seated position.   

Describe push rod overhead valve operating mechanism with neat sketch.

Description : Describe push rod overhead valve operating mechanism with neat sketch.

Last Answer : Push rod Overhead valve operating mechanism (OHV 4 -S engine): An overhead valve engine (OHV engine) is an engine in which the valves are placed over the cylinder head. The camshaft drive-chain ... . Overhead valve arrangement makes the engine slightly shorter than overhead camshaft.   OR  

What is the function of the friction clutch mechanism used in purifiers?

Description : What is the function of the friction clutch mechanism used in purifiers?

Last Answer : Ask 4/E or 2/E. It is a mechanical question.

Describe the working of pressure regulation in PFI system with the help of schematic diagram.

Description : Describe the working of pressure regulation in PFI system with the help of schematic diagram.

Last Answer : Working of Pressure Regulator in PFI System: The fuel pump provides more fuel than the maximum required by the engine. Fuel not used by the engine is returned to the fuel tank. The fuel rail supplies all injectors. ... between 2.0 and 3.5 bar and allows excess fuel to return to the fuel tank.

Draw a neat sketch of hydraulically operated clutch and label all parts.

Description : Draw a neat sketch of hydraulically operated clutch and label all parts.

Last Answer : hydraulically operated clutch

Draw a sketch of rack and pinion steering gear mechanism. Explain its working.

Description : Draw a sketch of rack and pinion steering gear mechanism. Explain its working.

Last Answer : Working: The rotary motion of the steering wheel is transmitted to the pinion of the steering gear through universal joints. The pinion is mesh with a rack. The circular motion of the pinion is ... relayed through the ball joints and the rods to the stub axles for the wheels to be steered.  

Explain the working of Ackerman steering gear mechanism with neat sketch.

Description : Explain the working of Ackerman steering gear mechanism with neat sketch.

Last Answer : Working: The whole mechanism of Ackerman Steering gear is on the back of the front wheels. The Ackerman steering gear consists of turning pairs The slotted links AM and BH are attached ... each end. The steering is affected by moving CD to the right or left of its nominal position. 

Explain working of over head valve mechanism with neat sketch.

Description : Explain working of over head valve mechanism with neat sketch.

Last Answer : Overhead valve mechanism: Figure shows the valve mechanism to operate the valve when it is in the cylinder head (in I and F head design). This type of mechanism requires two additional moving parts the ... to close. A spring (attached to the valve) returns the valve to its seated position.  

Explain the working of Scotch Yoke mechanism with neat sketch.

Description : Explain the working of Scotch Yoke mechanism with neat sketch.

Last Answer : Scotch yoke mechanism. This mechanism is used for converting rotary motion into a reciprocating motion. The inversion is obtained by fixing either the link 1 or link 3. In Fig. link 1 is fixed. In this ... link 4 (which corresponds to a frame) reciprocates. The fixed link 1 guides the frame

Draw a neat sketch of ‘Locomotive coupler’ mechanism. Explain its working in brief.

Description : Draw a neat sketch of ‘Locomotive coupler’ mechanism. Explain its working in brief.

Last Answer : Figure: Coupler Rod of Locomotive  (Link AD = Link BC = Crank Link CD = Coupling Rod Link AB = Fixed Link = Frame) Working of Coupler Rod of Locomotive: It is an ... center distance between them. This mechanism is meant for transmitting rotary motion from one wheel to the other wheel.

Describe the mechanism of chip formation during metal cutting with the help of sketch.

Description : Describe the mechanism of chip formation during metal cutting with the help of sketch.

Last Answer : Mechanism of chip formation : In Fig. the tool is considered stationary, and the work piece moves to the right. The metal is severely compressed in the area in front of the cutting tool. This causes ... movement transferred to the next element. The process is repetitive and a chip is formed. 

In a hundred-line exchange 24 two-motion selectors are used. Draw the schematic you suggest for this exchange and explain its working. How many simultaneous calls can be made during peak hour in this exchange?

Description : In a hundred-line exchange 24 two-motion selectors are used. Draw the schematic you suggest for this exchange and explain its working. How many simultaneous calls can be made during peak hour in this exchange?

Last Answer : The desired schematic for 100 lines exchange with 24 two motion selectors is shown in Fig.   In the case, 24 simultaneous calls can be put through the switch . Typically, a 24- ... selector. At the next step, the two-motion selector responds to the dial pulses for appropriate connection.

Using a combination of uniselectors and two motion selectors, draw a schematic of thousand line exchange and explain its working.

Description : Using a combination of uniselectors and two motion selectors, draw a schematic of thousand line exchange and explain its working.

Last Answer : The schematic diagram for such an exchange is given in Fig. Each subscriber is connected to a single rotary pre-selector switch at the exchange, the outputs from  this switch being ... further digits, connection is established, providing the called subscriber's to answer his telephone.  

Explain the working of Hydro power station with schematic layout.

Description : Explain the working of Hydro power station with schematic layout. 

Last Answer : Working of Hydro- Electric Power Plant: Water stored at high level by constructing dam across river. This stored water has potential energy. This stored water is passed to run the water ... energy and Alternator is coupled to water turbine which converts mechanical energy into electrical energy. 

Draw schematic diagram of welding transformer showing constructional features of a welding transformer. Also explain its working.

Description : Draw schematic diagram of welding transformer showing constructional features of a welding transformer. Also explain its working.

Last Answer : Constructional features of welding transformer: Working of welding transformer: i) It is a step down transformer that reduces the voltage from the source voltage to a voltage desired according to the demands of ... 230 V, 415 V Secondary voltage - 40 to 60 V Secondary current - 200 to 600 A

Draw the constructional details diagram of Centrifugal clutch. Explain its working principle.

Description : Draw the constructional details diagram of Centrifugal clutch. Explain its working principle.

Last Answer : Working Principle of Centrifugal Clutch: The centrifugal clutch uses centrifugal force, instead of spring force for keeping it in engaged position. Also, it does not require clutch pedal for ... increase of speed causes the shoe to press harder and enables more torque to be transmitted. 

Describe with neat sketch operation of PCV valve under different engine operating condition to control/ emission

Description : Describe with neat sketch operation of PCV valve under different engine operating condition to control/ emission

Last Answer : PCV Valve: It consists of a spring loaded tapered valve for flow control. The crankcase pressure and manifold vacuum act together to close the valve whereas the spring pressure tends to keep it open.( ... at idle and low speed (c)High speed/Load operation (d)Preventing backfire during cranking  

Describe the operating principle of PIN diode with neat sketch.

Description : Describe the operating principle of PIN diode with neat sketch.

Last Answer : Consider the structure of a PIN diode as shown in fig  A PIN diode operates under what is known as high-level injection.In other words,the intrinsic i region is flooded with charge ... results in faster operation of the diode,making it a suitable device for high frequency operations.

Describe the operating principle of photodiode with sketch

Description : Describe the operating principle of photodiode with sketch

Last Answer : Operating principle of photodiode: A photodiode is a PN junction or PIN structure. When a photon of sufficient energy strikes the diode, it excites an electron, thereby creating a mobile electron ... ) along its direction while the photocurrent remains virtually the same. Diagram optional:  

Describe re-entrant procedure with the help of schematic diagram.

Description : Describe re-entrant procedure with the help of schematic diagram.

Last Answer : Re-entrant Procedures: A procedure is said to be re-entrant, if it can be interrupted, used and re-entered without losing or writing over anything. To be a re-entrant, Procedure ... program execution flow reenters in the procedure1. These types of procedures are called reentrant procedures.

Explain slotted time quick return mechanism with neat sketch.

Description : Explain slotted time quick return mechanism with neat sketch. 

Last Answer : The slotted lever quick return mechanism is illustrated in Figs. a and b The crank AB (of adjustable length R) rotates with a uniform angular speed. The crank pin B is in the shape of a die block ... Fig. (b)) and the return stroke is completed in less time which is proportional to angle β.

Recommend & explain with neat sketch a suitable braking mechanism for the large WPP.

Description : Recommend & explain with neat sketch a suitable braking mechanism for the large WPP.

Last Answer : Braking Mechanism For The Large WPP: 1. Furling Mechanism: Furling allows the whole set of blades to change its position and blades turned away from wind, if wind speed is beyond safety limit. It ... 1.To harness optimum power from wind 2.To protect turbine in case of high wind speed.

Describe working of two wheeler charging system with labeled sketch

Description : Describe working of two wheeler charging system with labeled sketch

Last Answer : Working of charging system of two wheeler: The main components of two wheeler charging system are- 1.Battery 2.Regulator cum rectifier unit (Regulator and rectifier are assemble in one unit) 3. ... case of failure of fuse it disconnects the supply from regulator cum rectifier to battery.  

Describe working of constant mesh gear box with neat sketch.

Description : Describe working of constant mesh gear box with neat sketch.

Last Answer : Working of constant mesh gear box: A simplified diagram of constant mesh box has been shown in Figure. In this gear box, all gears on the main transmission shaft are constantly connected to corresponding ... In this way by sliding the second dog clutch, second and first gears are obtained.

Describe the working of collapsible steering column with sketch.

Description : Describe the working of collapsible steering column with sketch.

Last Answer : Collapsible steering column: Working: The design of these columns is such that they collapse due to impact forces caused during head-on collision of the vehicle. The collapsing columns ... Arrangement of a ball type collapsible steering column in normal mode and in collapsed condition.