A transformer core is laminated to?

A transformer core is laminated to?
by

1 Answer

Answer :

A transformer core is laminated to reduce eddy current losses.

by

Related questions

8 The transformer core is laminated to A. Reduce the copper losses B. Reduce the core losses C. Reduce the eddy current losses D. None of the above

Description : 8 The transformer core is laminated to A. Reduce the copper losses B. Reduce the core losses C. Reduce the eddy current losses D. None of the above

Last Answer : C. Reduce the eddy current losses

Why does the core of a transformer need to be laminated?

Description : Why does the core of a transformer need to be laminated?

Last Answer : Transformer cores are laminated to reduce eddy current loss.

why the Transformer core is laminated?

Last Answer : Transformer core is laminated to reduce Eddy current losses.

State any four characteristics of core type transformer.

Description : State any four characteristics of core type transformer.

Last Answer : Characteristics of core type transformer: i) It has one window. ii) It has one magnetic circuit. iii) Core surrounds the winding. iv) Average length of core is more. v) Area of cross ... Better cooling for winding. vii) Mechnical strength is comparatively less. viii) Repair and maintenance is easy.

The voltage applied to the H.V. side of a transformer during S.C. test is 2% of the rated voltage. The core loss

Description : The voltage applied to the H.V. side of a transformer during S.C. test is 2% of the rated voltage. The core loss as the fraction of its rated core loss is (a) 4% (b) 0.4% (c) 0.25% (d) 0.04%

Last Answer : 0.04%

The core flux of a practical transformer with a resistive load

Description : The core flux of a practical transformer with a resistive load  A) Is strictly constant with load changes B) Increases linearly with load C) Increases as the square root of the load D) Decrease with increased load

Last Answer : The core flux of a practical transformer with a resistive load Is strictly constant with load changes

For a pulse transformer, the material used for its core and the possible turn ration from primary to secondary

Description : For a pulse transformer, the material used for its core and the possible turn ration from primary to secondary are respectively   (A) ferrite : 20 : 1 (B) laminated iron : 1 :1 (C) ferrite : 1 : 1 (D) powered iron : 1: 1

Last Answer : For a pulse transformer, the material used for its core and the possible turn ration from primary to secondary are respectively ferrite : 1 : 1

In a transformer, low voltage winding is placed near the core in case of concentric windings so

Description : In a transformer, low voltage winding is placed near the core in case of concentric windings so as to  1. Reduce the leakage flux 2. Reduce the insulation requirement 3. Reduce the risk of voltage shock in case of insulation breakdown 4. Reduce the ... a) 1, 2, 3 (b) 2, 3, 4 (c) 1, 2, 3, 4 (d) 2, 3

Last Answer : In a transformer, low voltage winding is placed near the core in case of concentric windings so as to  1. Reduce the leakage flux 2. Reduce the insulation requirement 3. Reduce the risk of voltage shock in case of insulation breakdown 4. Reduce ... ) 1, 2, 3 (b) 2, 3, 4 (c) 1, 2, 3, 4 (d) 2, 3

The purpose of providing an iron core in a transformer is to?

Last Answer : The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

The purpose of providing iron core in a step-up transformer is?

Last Answer : The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

Material used for construction of transformer core is usually?

Last Answer : Material used for construction of transformer core is usually silicon steel.

The core used in high frequency transformer is usually?

Last Answer : The core used in high frequency transformer is usually air core .

When secondary of a current transformer is open-circuited its iron core will be?

Description : When secondary of a current transformer is open-circuited its iron core will be?

Last Answer : When secondary of a current transformer is open-circuited its iron core will be hot because of heavy iron losses taking place in it due to high flux density.

The size of a transformer core will depend on?

Description : The size of a transformer core will depend on?

Last Answer : The size of a transformer core will depend on frequency and area of the core.

Reduction in core losses and increase in permeability are obtained with transformer employing?

Description : Reduction in core losses and increase in permeability are obtained with transformer employing?

Last Answer : Reduction in core losses and increase in permeability are obtained with transformer employing core built-up of laminations of cold rolled grain oriented steel.

In a three-phase, squirrel-cage type, induction motor the rotating magnetic field is established by the _____________. A. current induced in the rotor windings B. application of a three-phase voltage supply to the stator windings C. laminated steel core and aluminum conductors in the rotor D. interaction of the magnetic field caused by the induced current in the squirrel-cage bars with the magnetic field of the stator

Description : In a three-phase, squirrel-cage type, induction motor the rotating magnetic field is established by the _____________. A. current induced in the rotor windings B. application of a three-phase voltage ... caused by the induced current in the squirrel-cage bars with the magnetic field of the stator

Last Answer : Answer: B

Why is the stator core of Alternator laminated?

Description : Why is the stator core of Alternator laminated?

Last Answer : The stator core of Alternator is laminated to reduce eddy current loss.

Transformer cores are laminated to reduce _____________. A. eddy currents B. secondary flux C. leakage flux D. all of the above

Description : Transformer cores are laminated to reduce _____________. A. eddy currents B. secondary flux C. leakage flux D. all of the above

Last Answer : Answer: A

24 Transformer cores are laminated in order to A. simplify its construction B. minimise eddy current loss C. reduce cost D. reduce hysteresis loss

Description : 24 Transformer cores are laminated in order to A. simplify its construction B. minimise eddy current loss C. reduce cost D. reduce hysteresis loss

Last Answer : B. Minimise eddy current loss

Transformer cores are laminated with (A) Low carbon steel. (B) Silicon sheet steel. (C) Nickel alloy steel. (D) Chromium sheet steel.

Description : Transformer cores are laminated with (A) Low carbon steel. (B) Silicon sheet steel. (C) Nickel alloy steel. (D) Chromium sheet steel.

Last Answer : (B) Silicon sheet steel.

Why do transformer coils laminated

Last Answer : Transformer core is laminated to reduce eddy current. Eddy current cause energy to lose from transformer 

Eddy current losses in transformer cores can be reduced by the use of 1. Solid cores 2. Laminated cores ...

Description : Eddy current losses in transformer cores can be reduced by the use of  1. Solid cores  2. Laminated cores  3. Ferrites  Select the correct answer using the codes given below : (a) 2 and 3 only (b). 1 and 2 only (c) 1 and 3 only (d) 1, 2 and 3

Last Answer : Eddy current losses in transformer cores can be reduced by the use of  1. Solid cores  2. Laminated cores  3. Ferrites  Select the correct answer using the codes given below : (a) 2 and 3 only (b). 1 and 2 only (c) 1 and 3 only (d) 1, 2 and 3

Explain direct loading test on single phase transformer with neat circuit diagram.

Description : Explain direct loading test on single phase transformer with neat circuit diagram. 

Last Answer : Direct loading test on single phase transformer with neat circuit diagram:   Direct loading test on transformer is carried out to calculate the losses, efficiency and voltage regulation of the ... voltage.  Efficiency and regulation can be calculated by using following formulae:   

Explain the effect of Harmonics on the Transformer.

Description : Explain the effect of Harmonics on the Transformer.

Last Answer : Effect of Harmonics on the Transformer:  1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations.  5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

List two special feature of welding transformer.

Description : List two special feature of welding transformer.

Last Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

State two applications of isolation transformer

Description : State two applications of isolation transformer

Last Answer : Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.

State why a transformer always have an efficiency of more than 90%.

Description : State why a transformer always have an efficiency of more than 90%.

Last Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.

Equivalent circuit of transformer

Description : Equivalent circuit of transformer

Last Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

Single phase transformer

Description : Single phase transformer

Last Answer : Single phase Transformer Transformer

What is the use of transformer?

Description : What is the use of transformer?

Last Answer : The use of transformer  is to do lower or raise  the voltage or currents in an electrical  circuit.  That's quite so simple. 

Transformer on DC

Description : Write about transformer on DC.

Last Answer : Transformer on DC : Transformer cannot work on DC. Transformer works on electromagnetic induction principle. Electromagnetic induction principle means when flux linking with coil changes and EMF induced in it ... winding insulation will burn. https://youtu.be/TVp_0fIfxqY

Why phasing out and polarity test is carried out on three phase transformer?

Description : Why phasing out and polarity test is carried out on three phase transformer?

Last Answer : The phasing out test is carried out to identify the windings (primary and secondary) of corresponding phase of the three phase transformer. The polarity test is carried out to identify the ... identical polarity of the primary and secondary windings of each phase of the three phase transformer.

State and justify which of the following two transformers is better: Transformer A = 4% voltage regulation Transformer B = 6% voltage regulation

Description : State and justify which of the following two transformers is better:  Transformer A = 4% voltage regulation  Transformer B = 6% voltage regulation

Last Answer : Transformer A with 4% voltage regulation is better.  Justification: Voltage regulation refers to the percentage change in secondary voltage when load is changed from no-load to full-load with primary voltage ... 4% voltage regulation, which is less as compared to 6% of transformer B, it is better.

Explain construction and working of single phase Auto transformer.

Description : Explain construction and working of single phase Auto transformer.

Last Answer : Construction of single phase auto transformer: (i) It has only one winding wound on a laminated circular magnetic core. (ii) The core is made of silicon steel stampings. (iii) The two terminals of the ... help of handle. 5) The same transformer can be used as step-up or step down auto-transformer

If the frequency of input voltage of a transformer is increased keeping the magnitude of voltage unchanged,

Description :  If the frequency of input voltage of a transformer is increased keeping the magnitude of voltage unchanged, then: A) both hysteresis loss and eddy current loss in the core will increase B) ... current loss will increase D) hysteresis loss will decrease but eddy current loss will remain unchanged

Last Answer :  If the frequency of input voltage of a transformer is increased keeping the magnitude of voltage unchanged, then: hysteresis loss will decrease but eddy current loss will remain unchanged

Full load copper loss in a transformer is 1600 watts. At half load the copper loss will be:

Description : Full load copper loss in a transformer is 1600 watts. At half load the copper loss will be: A) 6400 watt B) 1600 watt C) 800 watt D) 400 watt

Last Answer :  Full load cupper loss in a transformer is 1600 watts. At half load the cupper loss will be: 400 watt

The current transformer that is used to measure a 100 A current by 5 A ammeter is a_____.

Description : The current transformer that is used to measure a 100 A current by 5 A ammeter is a_____.

Last Answer : The current transformer that is used to measure a 100 A current by 5 A ammeter is a step up transformer

Three phase step-up transformer installed at power house, just before commencement of transmission line, have:

Description : Three phase step-up transformer installed at power house, just before commencement of transmission line, have:

Last Answer : Three phase step-up transformer installed at power house, just before commencement of transmission line, have: star delta connections

When two transformer of different kVA rating are connected in parallel they share the load in proportion to

Description : When two transformer of different kVA rating are connected in parallel they share the load in proportion to their respective kVA rating only when their:

Last Answer : When two transformer of different kVA rating are connected in parallel they share the load in proportion to their respective kVA rating only when their: P u impedance are equal

In a transformer the voltage regulation will be zero when it operates at

Description : In a transformer the voltage regulation will be zero when it operates at (A) unity p.f. (B) leading p.f. (C) lagging p.f. D) zero p.f. leading.

Last Answer : In a transformer the voltage regulation will be zero when it operates at leading p.f.

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Last Answer : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be 3.0 V.

The function of oil in a transformer is to provide

Description : The function of oil in a transformer is to provide  A) Insulation and cooling B) Protection against Lightning C) Protection against short circuit D) Lubrication

Last Answer : The function of oil in a transformer is to provide Insulation and cooling

A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the

Description : A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and ... reactances are neglected, the primary current is  A)1.41A B)2A C) 2.24A D)3A

Last Answer : A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and leakage reactances are neglected, the primary current is 2.24A

A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at

Description : A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at half load at the same power factor is  (A) 86.7% (B) 88.26% (C) 88.9% (D) 87.8%

Last Answer : A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at half load at the same power factor is 87.8%

A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage

Description : A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage load at which the transformer is expected to have maximum efficiency is  (A) 50.0% (B) 70.7% (C) 141.4% (D) 200.0%

Last Answer : A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage load at which the transformer is expected to have maximum efficiency is 70.7%

Which three-phase connection can be used in a transformer to introduce a phase difference of

Description : Which three-phase connection can be used in a transformer to introduce a phase difference of 30o between its output and corresponding input line voltages  (A) Star-Star (B) Star-Delta (C) Delta-Delta (D) Delta-Zigzag

Last Answer : Which three-phase connection can be used in a transformer to introduce a phase difference of 30o between its output and corresponding input line voltages  (A) Star-Star (B) Star-Delta (C) Delta-Delta (D) Delta-Zigzag

A single-phase, 50 kVA, 250 V/500 V two winding transformer has an efficiency of 95% at full load, unity

Description : A single-phase, 50 kVA, 250 V/500 V two winding transformer has an efficiency of 95% at full load, unity power factor. If it is re-configured as a 500 V/750 V auto-transformer, its efficiency at its new rated load at unity power factor will be  (A) 95.752% (B) 97.851% (C) 98.276% (D) 99.241%

Last Answer : A

A single-phase transformer has no-load loss of 64 W, as obtained from an open circuit test. When a short-circuit

Description : A single-phase transformer has no-load loss of 64 W, as obtained from an open circuit test. When a short-circuit test is performed on it with 90% of the rated currents flowing in its both LV and HV windings, ... .0% of the rated current (C) 80.0% of the rated current (D) 88.8% of the rated current

Last Answer : A single-phase transformer has no-load loss of 64 W, as obtained from an open circuit test. When a short-circuit test is performed on it with 90% of the rated currents flowing in its both ... measured loss is 81 W. The transformer has maximum efficiency when operated at 80.0% of the rated current

Which losses in a transformer varies significantly with load

Description : Which losses in a transformer varies significantly with load  a. Hysteresis losses b. Eddy current losses c. Copper losses d. Core losses 

Last Answer : Which losses in a transformer varies significantly with load Copper losses

The transformer utilization factor of full wave bridge rectifier is

Description : The transformer utilization factor of full wave bridge rectifier is   (A) 0.812 (B) 0.286 (C) 0.693 (D) 0.782

Last Answer : The transformer utilization factor of full wave bridge rectifier is 0.286