Which of the following in an application of D.C. motors? (a) Traction (b) Drives for process industry (c) Battery driven vehicles (d) Automatic control (e) All of the above

Which of the following in an application of D.C. motors?
(a) Traction
(b) Drives for process industry
(c) Battery driven vehicles
(d) Automatic control
(e) All of the above
by

1 Answer

Answer :

(e) All of the above
by

Related questions

By which of the following methods motor rating for variable load drives can be determined ? (a) Method of average losses (b) Equivalent current method (c) Equivalent torque method (d) Equivalent power method (e) All of the above.

Description : By which of the following methods motor rating for variable load drives can be determined ? (a) Method of average losses (b) Equivalent current method (c) Equivalent torque method (d) Equivalent power method (e) All of the above.

Last Answer : (e) All of the above.

Which of the following problem arises in D.C. motors which are fed from thyristor bridge circuits ? (a) Increased I R losses (b) Increased core losses (c) Poor commutation (d) Change in motor parameters (e) All of the above

Description : Which of the following problem arises in D.C. motors which are fed from thyristor bridge circuits ? (a) Increased I R losses (b) Increased core losses (c) Poor commutation (d) Change in motor parameters (e) All of the above

Last Answer : (e) All of the above

In self cooled motors the cooling time constant is about ______ than the heating time constant because cooling conditions are worse at standstill. (a) 2 to 3 times greater (b) 3 to 4 times greater (c) 4 to 5 times greater (d) none of the above

Description : In self cooled motors the cooling time constant is about ______ than the heating time constant because cooling conditions are worse at standstill. (a) 2 to 3 times greater (b) 3 to 4 times greater (c) 4 to 5 times greater (d) none of the above

Last Answer : (a) 2 to 3 times greater

Which ofthe following materials is used in the manufacture of resistance grids to be used in the starters of large motors ? (a) Copper (b) Aluminium (c) Steel (d) Cast-iron

Description : Which ofthe following materials is used in the manufacture of resistance grids to be used in the starters of large motors ? (a) Copper (b) Aluminium (c) Steel (d) Cast-iron

Last Answer : (d) Cast-iron

In induction motors, the length of air gap in kept as small as mechanically possible is order to have (a) low power factor (b) high power factor (c) high over load capacity (d) any of the above

Description : In induction motors, the length of air gap in kept as small as mechanically possible is order to have (a) low power factor (b) high power factor (c) high over load capacity (d) any of the above

Last Answer : (b) high power factor

D.C. servomotors are used in (a) purely D.C. control systems (6) purely AC. control systems (c) both D.C. and AC. control systems (d) none of the above

Description : D.C. servomotors are used in (a) purely D.C. control systems (6) purely AC. control systems (c) both D.C. and AC. control systems (d) none of the above

Last Answer : (a) purely D.C. control systems

The voltage control in electric supply networks in required on account of which of the following reasons ? (a) Adjustment of voltage at consumers premises within statutory limits (b) Control of active and reactive power (c) Adjustment of short period daily and seasonal voltage variations in accordance with variations of load (d) All of the above

Description : The voltage control in electric supply networks in required on account of which of the following reasons ? (a) Adjustment of voltage at consumers premises within statutory limits (b) Control of ... daily and seasonal voltage variations in accordance with variations of load (d) All of the above

Last Answer : (d) All of the above

cooling is the process of dissipating the armature and field winding losses to a cooling medium circulating within the winding insulation wall (a) Direct (b) Indirect (c) Conventional (d) Any ofthe above

Description : cooling is the process of dissipating the armature and field winding losses to a cooling medium circulating within the winding insulation wall (a) Direct (b) Indirect (c) Conventional (d) Any ofthe above

Last Answer : (a) Direct

Which of the following methods may be adopted to reduce the effects of armature reaction ? (a) Increase in length of air gap at pole tips (b) Increasing reluctance of pole tips (c) Compensating windings (d) Interpoles (e) All of the above

Description : Which of the following methods may be adopted to reduce the effects of armature reaction ? (a) Increase in length of air gap at pole tips (b) Increasing reluctance of pole tips (c) Compensating windings (d) Interpoles (e) All of the above

Last Answer : (e) All of the above

In a D.C. machine the current per brush arm should not be more than (a) 100 A (6) 200 A (e) 300 A (d) 400 A

Description : In a D.C. machine the current per brush arm should not be more than (a) 100 A (6) 200 A (e) 300 A (d) 400 A

Last Answer : (d) 400 A

For 275 kV transformers, using cold rolled grain oriented steel, which of the following values of flux density may be used? (a) 1.0 Wb/m2 (b) 1.1 Wb/m2 (c) 1.3 Wb/m2 (d) 1.6 Wb/m2 (e) None of the above

Description : For 275 kV transformers, using cold rolled grain oriented steel, which of the following values of flux density may be used? (a) 1.0 Wb/m2 (b) 1.1 Wb/m2 (c) 1.3 Wb/m2 (d) 1.6 Wb/m2 (e) None of the above

Last Answer : (d) 1.6 Wb/m2

The heat dissipating capability of transformers of ratings higher than 30 kVA in increased by providing which of the following ? (a) Corrugations (b) Fins (c) Tubes (d) Radiator tanks (e) All of the above

Description : The heat dissipating capability of transformers of ratings higher than 30 kVA in increased by providing which of the following ? (a) Corrugations (b) Fins (c) Tubes (d) Radiator tanks (e) All of the above

Last Answer : (e) All of the above

In transformers using hot rolled steel, the cross-section of the yoke is made about _____ greater than that of the core (a) 5 percent (b) 10 percent (c) 15 percent (d) 30 percent (e) none of the above

Description : In transformers using hot rolled steel, the cross-section of the yoke is made about _____ greater than that of the core (a) 5 percent (b) 10 percent (c) 15 percent (d) 30 percent (e) none of the above

Last Answer : (c) 15 percent

The design of electromagnets is based upon which of the following fundamental equations ? (a) Force equation (b) Magnetic circuit equation (c) Heating equation (d) Voltage equation (e) All of the above

Description : The design of electromagnets is based upon which of the following fundamental equations ? (a) Force equation (b) Magnetic circuit equation (c) Heating equation (d) Voltage equation (e) All of the above

Last Answer : (e) All of the above

Which ofthe following is an advantage of hydrogen cooling ? (a) Increase in efficiency (b) Increase in ratings (c) Increase in life (d) Smaller size of coolers (e) All ofthe above

Description : Which ofthe following is an advantage of hydrogen cooling ? (a) Increase in efficiency (b) Increase in ratings (c) Increase in life (d) Smaller size of coolers (e) All ofthe above

Last Answer : (e) All ofthe above

On which of the following variables heat convected depends ? (a) Power density (b) Temperature difference between heated surface and coolant (c) Thermal resistivity, density, specific heat (d) Gravitational constant (e) All ofthe above

Description : On which of the following variables heat convected depends ? (a) Power density (b) Temperature difference between heated surface and coolant (c) Thermal resistivity, density, specific heat (d) Gravitational constant (e) All ofthe above

Last Answer : (e) All ofthe above

The mcrease in heat dissipation by air blasts is due to increase in (a) conduction (b) convection (e) radiation (d) any ofthe above

Description : The mcrease in heat dissipation by air blasts is due to increase in (a) conduction (b) convection (e) radiation (d) any ofthe above

Last Answer : (b) convection

The change in flux linkages can be caused in which ofthe following ways ? (a) The flux is constant with respect to time and is stationary and the coil moves through it (b) The coil is stationary with respect to flux and the flux varies in magnitude with respect to time (c) Both the changes mentioned above occure together, i.e., the coil moves through a time varying field (d) All ofthe above

Description : The change in flux linkages can be caused in which ofthe following ways ? (a) The flux is constant with respect to time and is stationary and the coil moves through it (b) The coil is stationary with ... above occure together, i.e., the coil moves through a time varying field (d) All ofthe above

Last Answer : (d) All ofthe above

impose limitation on design. (a) Saturation (b) Temperature rise (c) Efficiency (d) Power factor (e) All above

Description : impose limitation on design. (a) Saturation (b) Temperature rise (c) Efficiency (d) Power factor (e) All above

Last Answer : (e) All above

In D.C. machines the number of slots per pole usually lies (a) between 2 to 4 (b) between 6 to 8 (c) between 9 to 16 (d) between 20 to 30

Description : In D.C. machines the number of slots per pole usually lies (a) between 2 to 4 (b) between 6 to 8 (c) between 9 to 16 (d) between 20 to 30

Last Answer : (c) between 9 to 16

In D.C. machines the usual limit of slot pitch is (a) between 5 to 10 mm (b) between 10 to 15 mm (c) between 15 to 20 mm (d) between 25 to 35 mm

Description : In D.C. machines the usual limit of slot pitch is (a) between 5 to 10 mm (b) between 10 to 15 mm (c) between 15 to 20 mm (d) between 25 to 35 mm

Last Answer : (d) between 25 to 35 mm

The operation of a D.C. machine with large air gap lengths is comparatively (a) quiet (b) noisy (c) either of the above (d) none of the above

Description : The operation of a D.C. machine with large air gap lengths is comparatively (a) quiet (b) noisy (c) either of the above (d) none of the above

Last Answer : (a) quiet

In D.C. machines, the ____ in field mmf results in increase in size and cost of machines. (a) increase (b) decrease (c) either of the above (d) none of the above

Description : In D.C. machines, the ____ in field mmf results in increase in size and cost of machines. (a) increase (b) decrease (c) either of the above (d) none of the above

Last Answer : (a) increase

In D.C. machines, ir order to prevent excessive distortion of field form by the armature reaction, the field mmf must be made (a) equal to that of armature mmf (b) less in comparison with the arma¬ture mmf (c) large in comparison with the arma-ture mmf (d) none of the above

Description : In D.C. machines, ir order to prevent excessive distortion of field form by the armature reaction, the field mmf must be made (a) equal to that of armature mmf (b) less in comparison with the arma¬ture mmf (c) large in comparison with the arma-ture mmf (d) none of the above

Last Answer : (c) large in comparison with the arma-ture mmf

D.C. machines designed with a large value of air gap length have (a) worst, ventilation (b) poor ventilation (c) better ventilation (d) none of the above

Description : D.C. machines designed with a large value of air gap length have (a) worst, ventilation (b) poor ventilation (c) better ventilation (d) none of the above

Last Answer : (c) better ventilation

In D.C. machines the width of the duct is usually (a) 4 mm (b) 6 mm (c) 8 mm (d) 10 mm

Description : In D.C. machines the width of the duct is usually (a) 4 mm (b) 6 mm (c) 8 mm (d) 10 mm

Last Answer : (d) 10 mm

In a D.C. machine, the value of peripheral speed should not, normally, exceed (a) 10 m/s (b) 20 m/s (c) 30 m/s (d) 40 m/s

Description : In a D.C. machine, the value of peripheral speed should not, normally, exceed (a) 10 m/s (b) 20 m/s (c) 30 m/s (d) 40 m/s

Last Answer : (c) 30 m/s

In a D.C. machine the number of brush arms is _____ the number of poles. (a) less than (b) equal to (c) greater than (d) none of the above

Description : In a D.C. machine the number of brush arms is _____ the number of poles. (a) less than (b) equal to (c) greater than (d) none of the above

Last Answer : (b) equal to

The weight of copper of both armature and field windings decreases with _____ in number of poles. (a) increase (b) decrease (c) either of the above (d) none of the above

Description : The weight of copper of both armature and field windings decreases with _____ in number of poles. (a) increase (b) decrease (c) either of the above (d) none of the above

Last Answer : (a) increase

________ is the common method of applying brushes to the commntator. (a) Radial (b) Trailing (c) Reaction (d) All of the above

Description : ________ is the common method of applying brushes to the commntator. (a) Radial (b) Trailing (c) Reaction (d) All of the above

Last Answer : (d) All of the above

Which of the following brushes can be used for high values of current density ? (a) Metal graphite brushes (b) Hard carbon brushes (c) Electro-graphitic brushes (d) Natural graphite brushes

Description : Which of the following brushes can be used for high values of current density ? (a) Metal graphite brushes (b) Hard carbon brushes (c) Electro-graphitic brushes (d) Natural graphite brushes

Last Answer : (a) Metal graphite brushes

_____ brushes are fragile and cause excessive wear of commutator, (a) Natural graphite (b) Hard carbon (c) Electro graphitic (d) Metal graphite

Description : _____ brushes are fragile and cause excessive wear of commutator, (a) Natural graphite (b) Hard carbon (c) Electro graphitic (d) Metal graphite

Last Answer : (a) Natural graphite

is usually used for brush rockers (a) Mild steel (b) Copper (c) Aluminium (d) Cast-iron

Description : is usually used for brush rockers (a) Mild steel (b) Copper (c) Aluminium (d) Cast-iron

Last Answer : (d) Cast-iron

The laminations of the armature of a D.C. machine are usually _____ thick. (a) 0.1 to 0.2 mm (b) 0.2 to 0.3 mm (c) 0.3 to 0.4 mm (d) 0.4 to 0.5 mm

Description : The laminations of the armature of a D.C. machine are usually _____ thick. (a) 0.1 to 0.2 mm (b) 0.2 to 0.3 mm (c) 0.3 to 0.4 mm (d) 0.4 to 0.5 mm

Last Answer : (d) 0.4 to 0.5 mm

The stator of a D.C. machine comprises of (a) main poles (6) interpoles (c) frame (d) all of the above

Description : The stator of a D.C. machine comprises of (a) main poles (6) interpoles (c) frame (d) all of the above

Last Answer : (d) all of the above

The surge phenomenon is particularly important in case of (a) low voltage transformers (b) medium voltage transformers (c) high voltage transformers (d) any of the above

Description : The surge phenomenon is particularly important in case of (a) low voltage transformers (b) medium voltage transformers (c) high voltage transformers (d) any of the above

Last Answer : (c) high voltage transformers

The cylindrical windings using circular conductors are used for current rating of (a) upto 20 A (b) upto 40 A (c) upto 60 A (d) upto 80 A

Description : The cylindrical windings using circular conductors are used for current rating of (a) upto 20 A (b) upto 40 A (c) upto 60 A (d) upto 80 A

Last Answer : (d) upto 80 A

The insulation between windings and grounded core and the insulation between the windings of the same phase is called (a) minor insulation (b) major insulation (c) either of the above (d) none of the above

Description : The insulation between windings and grounded core and the insulation between the windings of the same phase is called (a) minor insulation (b) major insulation (c) either of the above (d) none of the above

Last Answer : (b) major insulation

A practical formula for determining the thickness of insulation between low voltage and high voltage windings is (a) 1 + 0.2 kVmm (6) 2 + 0.5 kVmm (c) 4 + 0.7 kV mm (d) 5 + 0.9 kV mm

Description : A practical formula for determining the thickness of insulation between low voltage and high voltage windings is (a) 1 + 0.2 kVmm (6) 2 + 0.5 kVmm (c) 4 + 0.7 kV mm (d) 5 + 0.9 kV mm

Last Answer : (d) 5 + 0.9 kV mm

Which of the following is the basic consideration in the design of insulation ? (a) Electrical considerations (b) Mechanical considerations (c) Thermal considerations (d) All of the above

Description : Which of the following is the basic consideration in the design of insulation ? (a) Electrical considerations (b) Mechanical considerations (c) Thermal considerations (d) All of the above

Last Answer : (d) All of the above

The high voltage winding is usually which of the following type ? (a) Cylindrical winding with circular conductors (b) Cross-over winding with either circular or small rectangular conductors (c) Continuous disc type winding with rectangular conductors (d) All of the above types

Description : The high voltage winding is usually which of the following type ? (a) Cylindrical winding with circular conductors (b) Cross-over winding with either circular or small rectangular conductors (c) Continuous disc type winding with rectangular conductors (d) All of the above types

Last Answer : (d) All of the above types

A current density of _____ is ilsed for large power transformers with forced circulation of oil or with water cooling coils (a) 1.5 to 2.5 A/mm2 (b) 3.5 to 4.5 A/mm2 (c) 4.0 to 5.0 A/mm2 (d) 5.4 to 6.2 A/mm2

Description : A current density of _____ is ilsed for large power transformers with forced circulation of oil or with water cooling coils (a) 1.5 to 2.5 A/mm2 (b) 3.5 to 4.5 A/mm2 (c) 4.0 to 5.0 A/mm2 (d) 5.4 to 6.2 A/mm2

Last Answer : (d) 5.4 to 6.2 A/mm2

For large power transformers, self oil cooled type or air blast type which of the following values of current density may be used ? (a) 1.0 to 1.2 A/mm2 (b) 1.5 to 2.0 A/mm2 (c) 2.2 to 3.2 A/mm2 (d) 3.2 to 4.2 A/mm2

Description : For large power transformers, self oil cooled type or air blast type which of the following values of current density may be used ? (a) 1.0 to 1.2 A/mm2 (b) 1.5 to 2.0 A/mm2 (c) 2.2 to 3.2 A/mm2 (d) 3.2 to 4.2 A/mm2

Last Answer : (c) 2.2 to 3.2 A/mm2

The usual values of maximum flux densities for distribution transformers using hot rolled silicon steel are (a) 0.5 to 0.8 Wb/m2 (b) 0.8 to 1.0 Wb/m2 (c) 1.1 to 1.35 Wb/m2 (d) 1.4 to 1.8 Wb/m2

Description : The usual values of maximum flux densities for distribution transformers using hot rolled silicon steel are (a) 0.5 to 0.8 Wb/m2 (b) 0.8 to 1.0 Wb/m2 (c) 1.1 to 1.35 Wb/m2 (d) 1.4 to 1.8 Wb/m2

Last Answer : (c) 1.1 to 1.35 Wb/m2

D.C. windings are (a) sometimes 2-layer type (b) never 2-layer type (c) always 2-layer type (d) none of the above

Description : D.C. windings are (a) sometimes 2-layer type (b) never 2-layer type (c) always 2-layer type (d) none of the above

Last Answer : (c) always 2-layer type

The flash point of transformer oil should be higher than (a) 40°C (b) 60°C (c) 80°C (d) 104°C

Description : The flash point of transformer oil should be higher than (a) 40°C (b) 60°C (c) 80°C (d) 104°C

Last Answer : (d) 104°C

The forced oil and air circulation method is usual one for transformers of capacities (a) upto 5 MVA (b) upto 10 MVA (c) upto 20 MVA (d) 30 MVA upwards

Description : The forced oil and air circulation method is usual one for transformers of capacities (a) upto 5 MVA (b) upto 10 MVA (c) upto 20 MVA (d) 30 MVA upwards

Last Answer : (d) 30 MVA upwards

Transformers with a capacity of upto _____ have a cooling radiator system with natural cooling (a) 2 MVA (b) 5 MVA (c) 7.5 MVA (d) 10 MVA

Description : Transformers with a capacity of upto _____ have a cooling radiator system with natural cooling (a) 2 MVA (b) 5 MVA (c) 7.5 MVA (d) 10 MVA

Last Answer : (d) 10 MVA

Disc windings are primarily used in (a) short capacity transformers (b) medium capacity transformers (c) high capacity transformers (d) any of the above

Description : Disc windings are primarily used in (a) short capacity transformers (b) medium capacity transformers (c) high capacity transformers (d) any of the above

Last Answer : (c) high capacity transformers

Multi-layer helical windings are commonly used in the transformers as high voltage windings (a) upto 20 kV (b) upto 50 kV (c) upto 80 kV (d) for 110 kV and above

Description : Multi-layer helical windings are commonly used in the transformers as high voltage windings (a) upto 20 kV (b) upto 50 kV (c) upto 80 kV (d) for 110 kV and above

Last Answer : (d) for 110 kV and above