Determine the transformer tap ratios when the receiving end voltage is equal to the sending end voltage,...

Determine the transformer tap ratios when the receiving end voltage is equal to the sending end voltage, the high voltage line operates at 220 kV and transmit 80 MW at 0.8 pf and the impedance of the line is (40+j140)ohm. Assume tstr=1.0 

(A) 0.8 (B) 0.9 (C) 0.7 (D) 0.6 
by

1 Answer

Answer :

0.9 explanation given vs=vr convert in to phase voltage because impedence is always in phase line 220/root 3 then divided by reactive part that is 140 127.01/140=0.9 ans
by

Related questions

For a short line if the receiving end voltage is equal to the sending end voltage under loaded conditions...

Description : For a short line if the receiving end voltage is equal to the sending end voltage under loaded conditions: a) the sending end power factor is unity b) the receiving -end power factor is unity c) the sending-end power factor is leading d) the receiving end power factor is leading

Last Answer : For a short line if the receiving end voltage is equal to the sending end voltage under loaded conditions: the receiving end power factor is leading

If sending end voltage is Vs at no-load in a transmission line then receiving end voltage is if ABCD parameters of line is given a) Vs b) Vs/A c) 0 d) Infinity

Description : If sending end voltage is Vs at no-load in a transmission line then receiving end voltage is if ABCD parameters of line is given a) Vs b) Vs/A c) 0 d) Infinity

Last Answer : Ans: Vs/A

The power transmitted will be maximum when (a) corona losses are minimum (b) reactance is high (c) sending end voltage is more (d) receiving end voltage is more

Description : The power transmitted will be maximum when (a) corona losses are minimum (b) reactance is high (c) sending end voltage is more (d) receiving end voltage is more

Last Answer : (c) sending end voltage is more

An autotransformer is equipped with a 50% tap, a 65% tap, and an 80% tap. Which of the following statements is true concerning a load connected to the 50% tap? A. The load is receiving minimum voltage and minimum current. B. The load is receiving minimum voltage and maximum current. C. The load is receiving maximum voltage and minimum current. D. The load is receiving maximum voltage and maximum current.

Description : An autotransformer is equipped with a 50% tap, a 65% tap, and an 80% tap. Which of the following statements is true concerning a load connected to the 50% tap? A. The load is ... is receiving maximum voltage and minimum current. D. The load is receiving maximum voltage and maximum current.

Last Answer : Answer: B

The sending end and receiving end voltages of a three-phase transmission line are 10 kV/ph and 9.5 kV/ph,

Description : The sending end and receiving end voltages of a three-phase transmission line are 10 kV/ph and 9.5 kV/ph, respectively. If the resistance drop is 150 V/ph and receiving end power factor is 0.8, the sending end power factor is (A) 0.745 lagging (B) 0.775 lagging (C) 0.8 lagging (D) 0.85 lagging

Last Answer : Vscos¢s-Vrcos¢r=IR

Two transformers A and B having equal outputs and voltage ratios but unequal percentage

Description : Two transformers A and B having equal outputs and voltage ratios but unequal percentage impedances of 4 and 2 are operating in parallel. The transformer A will be overloaded by 

Last Answer : Two transformers A and B having equal outputs and voltage ratios but unequal percentage impedances of 4 and 2 are operating in parallel. The transformer A will be overloaded by 33%

In a tap changing transformer, the tappings are provided on (a) primary winding (b) secondary winding (c) high voltage winding (d) any of the above

Description : In a tap changing transformer, the tappings are provided on (a) primary winding (b) secondary winding (c) high voltage winding (d) any of the above

Last Answer : (b) secondary winding

Which of the following equipment, for regulating the voltage in distribution feeder, will be most economical ? (a) Static condenser (b) Synchronous condenser (c) Tap changing transformer (d) Booster transformer

Description : Which of the following equipment, for regulating the voltage in distribution feeder, will be most economical ? (a) Static condenser (b) Synchronous condenser (c) Tap changing transformer (d) Booster transformer

Last Answer : (d) Booster transformer

Have you ever said something to someone if they were sending and receiving texts while you were trying to have a conversation with them?

Description : Have you ever said something to someone if they were sending and receiving texts while you were trying to have a conversation with them?

Last Answer : I tell them when they’re done we can resume our conversation and walk away. They got miffed, but didn’t do it again.

What is the etiquette on sending thank you cards for receiving sympathy cards for the death of a loved one?

Description : What is the etiquette on sending thank you cards for receiving sympathy cards for the death of a loved one?

Last Answer : You can usually get away with none, maybe a thanks at the funeral. Most people send mass cards, and in all cases the recipients know that you know that their thoughts are with you. Am really sorry for your loss.

Identify the software that helps you in sending and receiving an E_mail: (a) MS_Office (b) Internet Explorer -Technology

Description : Identify the software that helps you in sending and receiving an E_mail: (a) MS_Office (b) Internet Explorer -Technology

Last Answer : (c) MS-Outlook is preferred E-mail client which is used for sending or receiving an E-mail.

E_mail is the process of sending and receiving messages ………… . -Technology

Description : E_mail is the process of sending and receiving messages ………… . -Technology

Last Answer : E-mail is the process of sending and receiving messageselectronically.

ADSL gives: a) Faster downloading speeds (receiving) than uploading speeds (sending) b) Slower downloading speeds (receiving) than uploading speeds (sending) c) Same downloading speeds (receiving) as uploading speeds (sending) d) None of These

Description : ADSL gives: a) Faster downloading speeds (receiving) than uploading speeds (sending) b) Slower downloading speeds (receiving) than uploading speeds (sending) c) Same downloading speeds (receiving) as uploading speeds (sending) d) None of These

Last Answer : a) Faster downloading speeds (receiving) than uploading speeds (sending)

MQTT is better than HTTP for sending and receiving data. A. True B. False

Description : MQTT is better than HTTP for sending and receiving data. A. True B. False

Last Answer : A. True

MQTT is better than HTTP for sending and receiving data. a) True b) False 4. MQTT is _________ protocol. a) Machine to Machine b) Internet of Things c) Machine to Machine and Internet of Things d) Machine things

Description : MQTT is _________ protocol. a) Machine to Machine b) Internet of Things c) Machine to Machine and Internet of Things d) Machine things

Last Answer : c) Machine to Machine and Internet of Things

MQTT is better than HTTP for sending and receiving data. A. True B. False

Description : MQTT is better than HTTP for sending and receiving data. A. True B. False

Last Answer : A. True 

The phenomenon qf rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the (a) Seeback effect (b) Ferranti effect (c) Raman effect (d) none of the above

Description : The phenomenon qf rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the (a) Seeback effect (b) Ferranti effect (c) Raman effect (d) none of the above

Last Answer : (b) Ferranti effect

The phenomenon qf rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the (a) Seeback effect (b) Ferranti effect (c) Raman effect (d) none of the above

Description : The phenomenon qf rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the (a) Seeback effect (b) Ferranti effect (c) Raman effect (d) none of the above

Last Answer : (b) Ferranti effect

A voltage of 1000 kV is applied to an overhead line with its receiving end...

Description : A voltage of 1000 kV is applied to an overhead line with its receiving end open. If the surge impedance of the line is 500 ohm, then the total surge power in the line ill

Last Answer : A voltage of 1000 kV is applied to an overhead line with its receiving end open. If the surge impedance of the line is 500 ohm, then the total surge power in the line ill 2000 MW .

A 60 Hz, 320 km lossless line has Bending end voltage 1.0 p.u, The receiving end voltage on no load is

Description : A 60 Hz, 320 km lossless line has Bending end voltage 1.0 p.u, The receiving end voltage on no load is?

Last Answer : A 60 Hz, 320 km lossless line has Bending end voltage 1.0 p.u, The receiving end voltage on no load is 1.088 p.u.

What are the necessary tests to determine the efficiency, voltage regulation, and temperature rise of winding & insulation of transformer?

Description : What are the necessary tests to determine the efficiency, voltage regulation, and temperature rise of winding & insulation of transformer?

Last Answer : 1.Direct loading test 2.Open circuit test 3. Short circuit test 4. Sumpner's or back to back test

In a Tap changing transformer on which side is the tap connected, primary side or secondary side?

Description : In a Tap changing transformer on which side is the tap connected, primary side or secondary side?

Last Answer : A. Tapings are always connected to high voltage winding side, because of low current. If we connect tapings to low voltage side, sparks will produce while tap changing operation due to high current.

Why the tap changers are always connected to HV side of the transformer?

Description : Why the tap changers are always connected to HV side of the transformer? 

Last Answer : During tap changing action the load current has to be shifted from one tap to another tap. In case HV wining the load current will be less. Hence lesser arcing will take place. 

Why there is no mixing of oil of tap changer and transformer?

Description : Why there is no mixing of oil of tap changer and transformer?

Last Answer : When the tap changing takes place arc is struck between the contacts. Due to this the oil inside the tap changer will be highly carbonised. If both oil get mixed up the quality of transformer tank oil will come down. This is not advisable. Hence both oils are kept separately. 

For what is the center tap on a transformer used?

Description : For what is the center tap on a transformer used?

Last Answer : Provides capability of developing two high-voltage outputs

a single phase full wave midpoint thyristor converter uses a 230/200V transformer with centre tap on the

Description : a single phase full wave midpoint thyristor converter uses a 230/200V transformer with centre tap on the secondary side. The P.I.V per thyristor is   (A) 100V (B)141.4V (C)200V (D)282.8V

Last Answer : d

How can I determine if my tap water is safe?

Description : How can I determine if my tap water is safe?

Last Answer : I would trust your senses. If it tastes funky, abandon ship! Britta filters aren’t that expensive if you have to resort to something else.

Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Description : Determine the dB gain of a receiving antenna which delivers a microvolt signal to a transmission line over that of an antenna that delivers a 20 microvolt signal under identical circumstances. A. 10 dB B. 6 dB C. 3 dB D. 8 dB

Last Answer : B. 6 dB

If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Description : If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Last Answer : B. critical phased array

The ratio that highlight the end result of business activities are known as ---------------- ratios a) Liquidity b) Leverage c) Activity d) Profitability

Description : The ratio that highlight the end result of business activities are known as ---------------- ratios a) Liquidity b) Leverage c) Activity d) Profitability

Last Answer : d) Profitability

a ____ is a pair of equal ratios. -General Knowledge

Description : a ____ is a pair of equal ratios. -General Knowledge

Last Answer : A proportion is a pair of equal ratios.

The length, breadth and height of a rectangular parallelopiped are in the ratios 6 : 3 : 1. If the surface area of a cube is equal -Maths 9th

Description : The length, breadth and height of a rectangular parallelopiped are in the ratios 6 : 3 : 1. If the surface area of a cube is equal -Maths 9th

Last Answer : answer:

For similarity, in addition to models being geometrically similar to prototype, the following in both cases should also be equal (A) Ratio of inertial force to force due to viscosity (B) Ratio of inertial force to force due to gravitation (C) Ratio of inertial force to force due to surface tension (D) All the four ratios of inertial force to force due to viscosity, gravitation, surface tension, and elasticity

Description : For similarity, in addition to models being geometrically similar to prototype, the following in both cases should also be equal (A) Ratio of inertial force to force due to viscosity (B) ... the four ratios of inertial force to force due to viscosity, gravitation, surface tension, and elasticity

Last Answer : Answer: Option D

What states that for any two bodies in thermal equilibrium, the ratios of emissive power to the absorptivity are equal?

Description : What states that for any two bodies in thermal equilibrium, the ratios of emissive power to the absorptivity are equal?  A. Kirchhoff’s radiation law  B. Newton’s law of cooling  C. Stefan-Boltzmann law  D. Hess’s law

Last Answer : Kirchhoff’s radiation law

In the mass spectrograph, two positively charged ions having the same velocity pass through a slit and enter a uniform magnetic field at right angles to their initial velocities. The ions will NOT be separated if: w) they have the same masses but different charges x) they have the same charges but different masses y) the products of their charges and their masses are equal z) the ratios of their charges to their masses are equal

Description : In the mass spectrograph, two positively charged ions having the same velocity pass through a slit and enter a uniform magnetic field at right angles to their initial velocities. The ions will NOT be ... charges and their masses are equal z) the ratios of their charges to their masses are equal  

Last Answer : ANSWER: Z -- THE RATIOS OF THEIR CHARGES TO THEIR MASSES ARE EQUAL 

If coil 'R1-R2' on the transmitter in figure 'A' shown in the illustration is turned 30 degrees clockwise, corresponding coil 'R1-R2' on the receiver should ____________. EL-0092 A. make coils 'S1-S2-S3' turn faster because of induced currents B. ring at the receiving station until the turning stops C. receive a higher voltage depending on the turns ratio D. align itself to the same position if free to move

Description : If coil 'R1-R2' on the transmitter in figure 'A' shown in the illustration is turned 30 degrees clockwise, corresponding coil 'R1-R2' on the receiver should ____________. EL-0092 A. make coils 'S1 ... a higher voltage depending on the turns ratio D. align itself to the same position if free to move

Last Answer : Answer: D

For a fixed value of complex power flow in a transmission line having a sending and voltage V, the real

Description : For a fixed value of complex power flow in a transmission line having a sending and voltage V, the real power loss will be proportional to  A) V B) v2 C) 1/V2 D)1/V

Last Answer : For a fixed value of complex power flow in a transmission line having a sending and voltage V, the real power loss will be proportional to 1/V2

Why tap changer is kept at neutral end?

Description : Why tap changer is kept at neutral end? 

Last Answer : a) To reduce insulation cost of tap changer. b) But reactance changeover the tap range increases. 

The frequency of the secondary voltage of a transformer will be..... A. less than frequency of the primary voltage B. equal to the primary voltage C. greater than the frequency of the primary voltage D. much greater than the frequency of the primary voltage

Description : The frequency of the secondary voltage of a transformer will be..... A. less than frequency of the primary voltage B. equal to the primary voltage C. greater than the frequency of the primary voltage D. much greater than the frequency of the primary voltage

Last Answer : B. Equal to the primary voltage

The voltage transformation ratio of a transformer is equal to the ratio of?

Description : The voltage transformation ratio of a transformer is equal to the ratio of?

Last Answer : The voltage transformation ratio of a transformer is equal to the ratio of secondary induced e.m.f. to primary induced e.m.f.

Do you think that being on the receiving end of discrimination and oppression makes you less likely to oppress others?

Description : Do you think that being on the receiving end of discrimination and oppression makes you less likely to oppress others?

Last Answer : That’s a tough question. It goes both ways. Some people are more likely to become oppressive of others (especially their oppressors), while others are equally likely to forgive their oppressors and live a joyful life with the creator.

What is the funniest thing. that was on the receiving end of your bad temper?

Description : What is the funniest thing. that was on the receiving end of your bad temper?

Last Answer : The only thing I don’t take my bad temper out on is my dogs!!!

Why are shunt reactors connected at the receiving end of long transmission line system:

Description : Why are shunt reactors connected at the receiving end of long transmission line system: (1) To increase the terminal voltage (2) To compensate voltage rise caused by capacitive charging at light load (3) To improve power factor (4) None of these

Last Answer : Why are shunt reactors connected at the receiving end of long transmission line system: To compensate voltage rise caused by capacitive charging at light load

Suppose transmission rate of a channel is 32 kbps. If there are ‘8’ routes from source to destination and each packet p contains 8000 bits. Total end to end delay in sending packet P is _____. a. 2 sec b. 3 sec c. 4 sec d. 1 sec

Description : Suppose transmission rate of a channel is 32 kbps. If there are ‘8’ routes from source to destination and each packet p contains 8000 bits. Total end to end delay in sending packet P is _____. a. 2 sec b. 3 sec c. 4 sec d. 1 sec

Last Answer : a. 2 sec

When a wave propagates on a transmission line, it suffers reflection several times at (a) tapping (b) load end (c) sending end (d) sending and other end (e) all of the above

Description : When a wave propagates on a transmission line, it suffers reflection several times at (a) tapping (b) load end (c) sending end (d) sending and other end (e) all of the above

Last Answer : (d) sending and other end

Why transformer have high and low voltage windings

Last Answer : According to our application, we need low voltage and high voltage transformer.  High voltage tsansformer also called step up transformer. Low voltage transformer also called step down transformer ... tranformer used in consumer side or substation or special application like battery,etc...

Give the classification of transformer based on: i) Construction ii) Voltage level iii) Number of phases iv) Applications

Description : Give the classification of transformer based on: i) Construction ii) Voltage level iii) Number of phases iv) Applications

Last Answer : Classification of transformer based on: i) Construction: Shell type, Core type, Berry type ii) Voltage level: Step-Up, Step-Down, iii) Number of phases: Single phase, Three phase iv) Applications: Power T/F, Distribution T/F

A d.c. voltage of 230 V is imposed on an unloaded 230 V, 50 Hz transformer, it will

Description : A d.c. voltage of 230 V is imposed on an unloaded 230 V, 50 Hz transformer, it will (A) give high secondary voltage (B) burn out (C) give secondary voltage as per k (D) None of these

Last Answer : A d.c. voltage of 230 V is imposed on an unloaded 230 V, 50 Hz transformer, it will burn out

Step-down transformer converts high voltage and low current into:

Description : Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

Last Answer : Step-down transformer converts high voltage and low current into: Low voltage and high current