Suppose transmission rate of a channel is 32 kbps. If there are ‘8’ routes from source to destination and each packet p contains 8000 bits. Total end to end delay in sending packet P is _____. a. 2 sec b. 3 sec c. 4 sec d. 1 sec

Suppose transmission rate of a channel is
32 kbps. If there are ‘8’ routes from source
to destination and each packet p contains
8000 bits. Total end to end delay in sending
packet P is _____.
a. 2 sec
b. 3 sec
c. 4 sec
d. 1 sec
by

1 Answer

Answer :

a. 2 sec
by

Related questions

Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it is assumed that each sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Description : Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it ... sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Last Answer : (C) 128 kbps

A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of an acknowledgement is 100 bytes and the transmission rate at the receiver is 8 Kbps. The one-way propagation delay is 100 milliseconds. Assuming no frame is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Description : A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of ... is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Last Answer : a. 2500

If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ______. a. 64 Kbps b. 32 Mbps c. 32 Kbps d. 64 MbpS

Description : If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ______. a. 64 Kbps b. 32 Mbps c. 32 Kbps d. 64 MbpS

Last Answer : c. 32 Kbps

Which of the following assertions is FALSE about the Internet Protocol (IP)? a. It is possible for a computer to have multiple IP addresses b. IP packets from the same source to the same destination can take different routes in the network c. IP ensures that a packet is discarded if it is unable to reach its destination within a given number of hops d. The packet source cannot set the route of an outgoing packets; the route is determined only by the routing tables in the routers on the way

Description : Which of the following assertions is FALSE about the Internet Protocol (IP)? a. It is possible for a computer to have multiple IP addresses b. IP packets from the same source to the same ... outgoing packets; the route is determined only by the routing tables in the routers on the way

Last Answer : d. The packet source cannot set the route of an outgoing packets; the route is determined only by the routing tables in the routers on the way

If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ............... (A) 64 Kbps (B) 32 Mbps (C) 32 Kbps (D) 64 Mbps

Description : If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ............... (A) 64 Kbps (B) 32 Mbps (C) 32 Kbps (D) 64 Mbps

Last Answer : (C) 32 Kbps

Consider a CSMA/CD network that transmits data at a rate of 100 Mbps (108 bits per second) over a 1 km (kilometre) cable with no repeaters. If the minimum frame size required for this network is 1250 bytes, what is the signal speed (km/sec) in the cable? a. 8000 b. 10000 c. 16000 d. 20000

Description : Consider a CSMA/CD network that transmits data at a rate of 100 Mbps (108 bits per second) over a 1 km (kilometre) cable with no repeaters. If the minimum frame size required for this network is 1250 bytes, what is the signal speed (km/sec) in the cable? a. 8000 b. 10000 c. 16000 d. 20000

Last Answer : d. 20000

A noiseless 3 KHz Channel transmits bits with binary level signals. What is the maximum data rate? A. 3 Kbps B. 6 Kbps C. 12 Kbps D. 24 Kbps

Description : A noiseless 3 KHz Channel transmits bits with binary level signals. What is the maximum data rate? A. 3 Kbps B. 6 Kbps C. 12 Kbps D. 24 Kbps

Last Answer : 6 Kbps

In virtual circuit network each packet contains ___________ a. full source and destination address b. a short VC number c. only source address d. only destination address

Description : In virtual circuit network each packet contains ___________ a. full source and destination address b. a short VC number c. only source address d. only destination address

Last Answer : b. a short VC number

In virtual circuit network each packet contains ___________ A. full source and destination address B. a short VC number C. only source address D. only destination address

Description : In virtual circuit network each packet contains ___________ A. full source and destination address B. a short VC number C. only source address D. only destination address

Last Answer : B. a short VC number

Station A uses 32 byte packets to transmit messages to Station B using a sliding window protocol. The round trip delay between A and B is 80 milliseconds and the bottleneck bandwidth on the path between A and B is 128 kbps. What is the optimal window size that A should use? a. 20 b. 40 c. 160 d. 320

Description : Station A uses 32 byte packets to transmit messages to Station B using a sliding window protocol. The round trip delay between A and B is 80 milliseconds and the bottleneck bandwidth on the path between A and B ... What is the optimal window size that A should use? a. 20 b. 40 c. 160 d. 320

Last Answer : b. 40

Assume that we need to download text documents at the rate of 100 pages per minute. A page is an average of 24 lines with 80 characters in each line and each character requires 8 bits. Then the required bit rate of the channel is ................ (A) 1.636 Kbps (B) 1.636 Mbps (C) 2.272 Mbps (D) 3.272 Kbps

Description : Assume that we need to download text documents at the rate of 100 pages per minute. A page is an average of 24 lines with 80 characters in each line and each character requires 8 bits. Then the required bit rate of the channel is ... ...... (A) 1.636 Kbps (B) 1.636 Mbps (C) 2.272 Mbps (D) 3.272 Kbps

Last Answer : Answer: Marks given to all

Which of the following use routes with packet filtering rules to allow or deny access based on source address, destination address, or port number? 1) Application layer Firewall 2) Packet Filtering Firewall 3) Router enhanced firewall 4) IP enabled firewall

Description : Which of the following use routes with packet filtering rules to allow or deny access based on source address, destination address, or port number? 1) Application layer Firewall 2) Packet Filtering Firewall 3) Router enhanced firewall 4) IP enabled firewall

Last Answer : 2) Packet Filtering Firewall

Which of the following use routes with packet filtering rules to allow or deny access based on source address, destination address, or port number? 1 Application layer Firewall 2 Packet Filtering Firewall 3 Router enhanced firewall 4 IP enabled firewall

Description : Which of the following use routes with packet filtering rules to allow or deny access based on source address, destination address, or port number? 1 Application layer Firewall 2 Packet Filtering Firewall 3 Router enhanced firewall 4 IP enabled firewall

Last Answer : 2 Packet Filtering Firewall

Suppose that the one-way propagation delay for a 100 Mbps Ethernet having 48-bit jamming signal is 1.04 micro-seconds. The minimum frame size in bits is: a. 112 b. 160 c. 208 d. 256

Description : Suppose that the one-way propagation delay for a 100 Mbps Ethernet having 48-bit jamming signal is 1.04 micro-seconds. The minimum frame size in bits is: a. 112 b. 160 c. 208 d. 256

Last Answer : d. 256

12 voice channels are sampled at 8000 sampling rate and encoded into 8 bit PCM word. Determine the rate of the data stream. a. 354 kbps b. 750 kbps c. 768 kbps d. 640 kbps

Description : 12 voice channels are sampled at 8000 sampling rate and encoded into 8 bit PCM word. Determine the rate of the data stream. a. 354 kbps b. 750 kbps c. 768 kbps d. 640 kbps

Last Answer : c. 768 kbps

The _______ address in theheader ofa packet in adatagram network normally remains thesame during the entire journeyof the packet. A) source B) destination C) local D) none of the above

Description : The _______ address in theheader ofa packet in adatagram network normally remains thesame during the entire journeyof the packet. A) source B) destination C) local D) none of the above

Last Answer : destination

A 8-Mbps tokenring has atoken holding timer value of 10 msec. What is the longest frame (assumeheader bits are negligible) that canbe sent on this ring? A. 8000 B frame B. 80,000 B frame C. 8 x 105 bit frame D. 10,000 B frame

Description : A 8-Mbps tokenring has atoken holding timer value of 10 msec. What is the longest frame (assumeheader bits are negligible) that canbe sent on this ring? A. 8000 B frame B. 80,000 B frame C. 8 x 105 bit frame D. 10,000 B frame

Last Answer : 10,000 B frame

Station A uses 32 byte packets to transmit messages to station B using sliding window protocol. The round trip delay between A and B is 40 milli seconds and the bottleneck bandwidth on the path between A and B is 64 kbps. The optimal window size of A is (1) 20 (2) 10 (3) 30 (4) 40

Description : Station A uses 32 byte packets to transmit messages to station B using sliding window protocol. The round trip delay between A and B is 40 milli seconds and the bottleneck bandwidth on the path between A and B is 64 kbps. The optimal window size of A is (1) 20 (2) 10 (3) 30 (4) 40

Last Answer : (2) 10

In ISDN, what is the basic access B channel data rate? A. 32 kbps B. 64 kbps C. 144 kbps D. 16 kbps

Description : In ISDN, what is the basic access B channel data rate? A. 32 kbps B. 64 kbps C. 144 kbps D. 16 kbps

Last Answer : B. 64 kbps

What is the data rate of the ISDN Basic access B channel? A. 192 kbps B. 32 kbps C. 64 kbps D. 144 kbps

Description : What is the data rate of the ISDN Basic access B channel? A. 192 kbps B. 32 kbps C. 64 kbps D. 144 kbps

Last Answer : C. 64 kbps

State weather the following statement is true or false for IPV6 Addressing 1). IPV6 is a routable protocol that addresses, routes, fragments, and reassembles packets 2).IPV6 is a connectionless, unreliable datagram protocol. 3). An IPV6 packet consists of an IPV6 header and an IPV6 payload. A. 1. True, 2. true, 3. true B. 1. true, 2. false, 3. false C. 1. false, 2. false, 3. false D. 1.false, 2. true, 3. true

Description : State weather the following statement is true or false for IPV6 Addressing 1). IPV6 is a routable protocol that addresses, routes, fragments, and reassembles packets 2).IPV6 is a connectionless, unreliable datagram protocol. 3). ... C. 1. false, 2. false, 3. false D. 1.false, 2. true, 3. true

Last Answer : A. 1. True, 2. true, 3. true

Determine from the following the basic mode of transmission system in the public data network in which data are transferred from the source to the network and from the network to the destination in the frame format. A. Voice mode B. Asynchronous mode C. Synchronous mode D. Packet mode

Description : Determine from the following the basic mode of transmission system in the public data network in which data are transferred from the source to the network and from the network to the destination in the frame format. A. Voice mode B. Asynchronous mode C. Synchronous mode D. Packet mode

Last Answer : D. Packet mode

A pure ALOHA Network transmits 200 bit frames using a shared channel with 200 Kbps bandwidth. If the system (all stations put together) produces 500 frames per second, then the throughput of the system is ______. a. 0.384 b. 0.184 c. 0.286 d. 0.58

Description : A pure ALOHA Network transmits 200 bit frames using a shared channel with 200 Kbps bandwidth. If the system (all stations put together) produces 500 frames per second, then the throughput of the system is ______. a. 0.384 b. 0.184 c. 0.286 d. 0.58

Last Answer : b. 0.184

In______ transmission, wesend1 start bit (0) at thebeginningand 1 or more stop bits (1s) at the end of each byte. A) synchronous B) asynchronous C) isochronous D) none of the above

Description : In______ transmission, wesend1 start bit (0) at thebeginningand 1 or more stop bits (1s) at the end of each byte. A) synchronous B) asynchronous C) isochronous D) none of the above

Last Answer : asynchronous

Which one of the following statements is FALSE? a. Packet switching leads to better utilization of bandwidth resources than circuit switching. b. Packet switching results in less variation in delay than circuit switching. c. Packet switching requires more per packet processing than circuit switching d. Packet switching can lead to reordering unlike in circuit switching

Description : Which one of the following statements is FALSE? a. Packet switching leads to better utilization of bandwidth resources than circuit switching. b. Packet switching results in less variation ... than circuit switching d. Packet switching can lead to reordering unlike in circuit switching

Last Answer : Packet switching results in less variation in delay than circuit switching.

In computer networks _________ is a characteristic that a flow needs where Lack of it means losing a packet or acknowledgment, which entails retransmission. A. Reliability B. Delay C. Jitter D. Bandwidth

Description : In computer networks _________ is a characteristic that a flow needs where Lack of it means losing a packet or acknowledgment, which entails retransmission. A. Reliability B. Delay C. Jitter D. Bandwidth

Last Answer : A. Reliability

The program used to determine the round trip delay between a workstation and a destination address is a. Tracert b. Traceroute c. Ping d. Pop

Description : The program used to determine the round trip delay between a workstation and a destination address is a. Tracert b. Traceroute c. Ping d. Pop

Last Answer : b. Traceroute

In _______delivery, the deliverer of theIP packet and the destination are on different networks. A) aconnection-oriented B) a direct C) an indirect D) none of the above

Description : In _______delivery, the deliverer of theIP packet and the destination are on different networks. A) aconnection-oriented B) a direct C) an indirect D) none of the above

Last Answer : an indirect

In _______delivery, both thedeliverer of the IP packet and the destination are on the same network. A) aconnectionless B) a direct C) an indirect D) none of the above

Description : In _______delivery, both thedeliverer of the IP packet and the destination are on the same network. A) aconnectionless B) a direct C) an indirect D) none of the above

Last Answer : a direct

For which one of the following reasons does Internet Protocol (IP) use the time-to- live (TTL) field in the IP datagram header? a. Ensure packets reach destination within that time b. Discard packets that reach later than that time c. Prevent packets from looping indefinitely d. Limit the time for which a packet gets queued in intermediate routers.

Description : For which one of the following reasons does Internet Protocol (IP) use the time-to- live (TTL) field in the IP datagram header? a. Ensure packets reach destination within that time b. ... packets from looping indefinitely d. Limit the time for which a packet gets queued in intermediate routers.

Last Answer : c. Prevent packets from looping indefinitely

How much packet data rate per user is supported by W-CDMA if the user is stationary? a) 2.048 Kbps b) 100 Mbps c) 2.048 Mbps d) 1 Gbps

Description : How much packet data rate per user is supported by W-CDMA if the user is stationary? a) 2.048 Kbps b) 100 Mbps c) 2.048 Mbps d) 1 Gbps

Last Answer : c) 2.048 Mbps

When 2 or more bits in a data unit has been changed during the transmission, the error is called _____ a. random error b. burst error c. inverted error d. double error

Description : When 2 or more bits in a data unit has been changed during the transmission, the error is called _____ a. random error b. burst error c. inverted error d. double error

Last Answer : b. burst error

Suppose the round trip propagation delay for a 10 Mbps Ethernet having 48-bit jamming signal is 46.4 ms. The minimum frame size is a. 94 b. 416 c. 464

Description : Suppose the round trip propagation delay for a 10 Mbps Ethernet having 48-bit jamming signal is 46.4 ms. The minimum frame size is a. 94 b. 416 c. 464

Last Answer : c. 464

The distance between two stations M and N is L kilometers. All frames are K bits long. The propagation delay per kilometer is t seconds. Let R bits/second be the channelcapacity. Assuming that processing delay is negligible, the minimum number of bits for the sequence number field in a frame for maximum utilization, when the sliding window protocol used is: a. A b. B c. C d. D

Description : The distance between two stations M and N is L kilometers. All frames are K bits long. The propagation delay per kilometer is t seconds. Let R bits/second be the channel capacity. Assuming that processing ... maximum utilization, when the sliding window protocol used is: a. A b. B c. C d. D

Last Answer : c. C

What is the channel symbol rate in Bluetooth for each user? a) 270.833 Kbps b) 1 Gbps c) 100 Mbps d) 1 Mbps

Description : What is the channel symbol rate in Bluetooth for each user? a) 270.833 Kbps b) 1 Gbps c) 100 Mbps d) 1 Mbps

Last Answer : d) 1 Mbps

A multiplexer combines four 100-Kbps channels using a time slot of 2 bits. What is the bit rate? (A) 100 Kbps (B) 200 Kbps (C) 400 kbps (D) 1000 Kbps

Description : A multiplexer combines four 100-Kbps channels using a time slot of 2 bits. What is the bit rate? (A) 100 Kbps (B) 200 Kbps (C) 400 kbps (D) 1000 Kbps

Last Answer : (C) 400 kbps

Maximum data transfer rate of the optical fiber is……….? a. 50 kbps b. 1000 kbps c. 1000 Mbps d. None of the these

Description : Maximum data transfer rate of the optical fiber is……….? a. 50 kbps b. 1000 kbps c. 1000 Mbps d. None of the these

Last Answer : c. 1000 Mbps

An IPv4 address consistsof _______ bits. A) 4 B) 8 C) 32 D) 64

Description : An IPv4 address consistsof _______ bits. A) 4 B) 8 C) 32 D) 64

Last Answer : 32

Which processes does TCP, but not UDP, use? Source Port - 16 bits, Destination Port - 16 bits, Length - 16 Bits, Checksum - 16 bits, Data * Destination Port - 16 bits, Source Port - 16 bits, Length - 16 Bits, Checksum - 16bits, Data * Source Port - 16 bits, Destination Port - 16 bits, Checksum - 16 Bits, Length - 16 bits, Data * Source Port - 8 bits, Destination Port - 8 bits, Length -8 Bits, Checksum - 8 bits, Data

Description : Which processes does TCP, but not UDP, use?Source Port - 16 bits, Destination Port - 16 bits, Length - 16 Bits, Checksum - 16 bits, Data * Destination Port - 16 bits, Source Port - 16 bits, Length - ... * Source Port - 8 bits, Destination Port - 8 bits, Length -8 Bits, Checksum - 8 bits, Data

Last Answer : Correct answer: A The UDP format for a segment is as follows: Source Port 16 bits Destination Port 16 bits Length 16 bits Checksum 16 bits Data xx bits

There are 10 users plugged into a hub running 10Mbps half-duplex.and a serverconnected to the switch running 10Mbps half- duplex as well. Find the bandwidth does each host have to the server? a. 100 kbps b. 1 Mbps c. 2 Mbps d. 10 Mbps

Description : There are 10 users plugged into a hub running 10Mbps half-duplex.and a server connected to the switch running 10Mbps half- duplex as well. Find the bandwidth does each host have to the server? a. 100 kbps b. 1 Mbps c. 2 Mbps d. 10 Mbps

Last Answer : d. 10 Mbps

Each IP address can identify the ………... or ………... of IP packets. A. source, destination B. length, size C. source, length D. Size , destination

Description : Each IP address can identify the ………... or ………... of IP packets. A. source, destination B. length, size C. source, length D. Size , destination

Last Answer : A. source, destination

What is the usualnumber of bits transmitted simultaneously inparalleldata transmission used by microcomputers? A. 16 B. 9 C. 8 D. 4 E. None of the above

Description : What is the usualnumber of bits transmitted simultaneously inparalleldata transmission used by microcomputers? A. 16 B. 9 C. 8 D. 4 E. None of the above

Last Answer : 9

How many 8-bit characters can be transmitted per second over a 9600 baud serial communication link using asynchronous mode of transmission with one start bit, eight data bits, two stop bits, and one parity bit ? a. 600 b. 800 c. 876 d. 1200

Description : How many 8-bit characters can be transmitted per second over a 9600 baud serial communication link using asynchronous mode of transmission with one start bit, eight data bits, two stop bits, and one parity bit ? a. 600 b. 800 c. 876 d. 1200

Last Answer : b. 800

Which of the following statement is False about the efficiency of the given channel? a. If we want to send big packets on the channel, then Stop and Wait is good choice. b. If length of packet increases, efficiency of channel also increases. c. Distance between sender and receiver is directly proportional to efficiency of channel. d. Efficient might be less if capacity of channel is high

Description : Which of the following statement is False about the efficiency of the given channel? a. If we want to send big packets on the channel, then Stop and Wait is good choice. b. If length ... is directly proportional to efficiency of channel. d. Efficient might be less if capacity of channel is high

Last Answer : Distance between sender and receiver is directly proportional to efficiency of channel.

In an Ethernet local area network, which one of the following statements is TRUE ? a. A station stops to sense the channel once it starts transmitting a frame. b. The purpose of the jamming signal is to pad the frames that are smaller than the minimum frame size. c. A station continues to transmit the packet even after the collision is detected. d. The exponential backoff mechanism reduces the probability of collision on retransmissions

Description : In an Ethernet local area network, which one of the following statements is TRUE ? a. A station stops to sense the channel once it starts transmitting a frame. b. The purpose ... collision is detected. d. The exponential backoff mechanism reduces the probability of collision on retransmissions

Last Answer : The exponential backoff mechanism reduces the probability of collision on retransmissions

what is full form of EDSAC: a. Electronic delay source accumulator calculator b. Electronic delay storage automatic code c. Electronic destination source automatic calculator d. Electronic delay storage automatic calculator

Description : what is full form of EDSAC: a. Electronic delay source accumulator calculator b. Electronic delay storage automatic code c. Electronic destination source automatic calculator d. Electronic delay storage automatic calculator

Last Answer : d. Electronic delay storage automatic calculator

Which of the following couldnot be an Ethernet multicast destination? A) B7:7B:6C:DE:10:00 B) 7B:AA:C1:23:45:32 C) 7C:56:21:1A:DE:F4 D) 83:32:21:21:4D:34

Description : Which of the following couldnot be an Ethernet multicast destination? A) B7:7B:6C:DE:10:00 B) 7B:AA:C1:23:45:32 C) 7C:56:21:1A:DE:F4 D) 83:32:21:21:4D:34

Last Answer : 7C:56:21:1A:DE:F4

Which of the following couldnot be an Ethernet unicast destination? A) 43:7B:6C:DE:10:00 B) 44:AA:C1:23:45:32 C) 46:56:21:1A:DE:F4 D) 48:32:21:21:4D:34

Description : Which of the following couldnot be an Ethernet unicast destination? A) 43:7B:6C:DE:10:00 B) 44:AA:C1:23:45:32 C) 46:56:21:1A:DE:F4 D) 48:32:21:21:4D:34

Last Answer : 43:7B:6C:DE:10:0

When using access lists, what does a Cisco router check first? * To see if the packet is routable or bridgeable * The destination address * The source address * The packet contents

Description : When using access lists, what does a Cisco router check first? * To see if the packet is routable or bridgeable * The destination address * The source address * The packet contents

Last Answer : Correct answer: A The first thing checked is to see if the packet is routable or bridgeable. If it is not, the packet will be dropped.